ID |
Date |
Author |
Project |
Subject |
Run Number |
Events |
XYPosition |
Cooling |
Data |
3
|
Wed Jun 3 17:23:07 2015 |
Thomas Bergauer | Belle II FADC (H6A) | XY stage positions | | | | | Unknown |
x-Achse: positiv Richtung Saleve (counting room)
y-Achse: positiv Richtung UNTEN!!
position of laddertestbox xy stages:
Rev. Pos (BWD Sensor, BWD, Oben) x= 82.3, y=110.6
Mitte Sensor:
Pos 1: (mitte BWD sensor): x=144.74, y=80.8
Pos 2: (mitte Origami -z): x=269.62, y=80.8
Pos 3: (mitte Origami ce): x=394.42, y=80.8
Pos 4 (mitte FWD Micron Sensor): x=517, y=80.8
Ecke:
Pos 5 (Ecke BWD sensor): x=92.3, y=105.6
Pos 6 (Ecke Origami -z): x=217.18, y=105.6
Pos 7 (Ecke Origami ce): x=342.06, y=105.6
Pos 8 (Ecke FWD sensor): x=467,62, y=56,3
Pos 9 (Ecke FWD sensor): x=568,33 y=64,48 |
Attachment 1: L5_Class_B-.PNG
|
|
36
|
Sun Jun 7 14:44:29 2015 |
Thomas Bergauer | SVD3 (H6B) | XY Stage and DUT Positions | | | | | Unknown |
Coordinate system:
pos x-Direction = Jura side
pos y-Direction = Down
Zero-point is in the top right corner in Beam direction
absolute Position of PI Stages:
Pos 1: x=100 mm, y=79 mm (Hits in APV 3 und 8-9 in p-Seite und 14 und 17 in n-Seite )
Pos 2: x=69.3 mm, y=79 mm (Hits in APV 3-4 und 8-9 in p-Seite und 13 und 18 in n-Seite)
Pos 3: x=38.6 mm, y=84 mm
Pos 4: x=130.7 mm, y=84 mm
Pos 5: x=30.5 mm, y= 99.74 mm (wide side top)
Pos 6: x=136.08 mm, y= 91.49 mm (narrow side top)
Pos 7: x= 30.5 mm, y= 79 mm (wide side center)
Pos 8: x=136.08 mm, y= 79 mm (narrow side center)
Pos 9: x=30.5 mm, y= 60.67 mm (wide side down)
Pos 10: x= 136.08mm, y=68.9 mm (narrow side down) |
Attachment 1: FWD-BWD.PNG
|
|
Attachment 2: apv-numbering.jpg
|
|
Attachment 3: FWD-BWD_Bemaßung.PNG
|
|
37
|
Sun Jun 7 15:03:31 2015 |
Thomas Bergauer | SVD3 (H6B) | hardware run with TLU and Telescope | hw050 | 50000 | 2 | No | Good |
RUN WITH SVD3 plus telescope
EUDET Run 50
Mimosa Threshold 7
Pos 2: x=69.3 mm, y=79 mm (Hits in APV 3-4 und 8-9 in p-Seite und 13 und 18 in n-Seite) |
40
|
Sun Jun 7 20:03:09 2015 |
Thomas Bergauer | SVD3 (H6B) | hardware run with TLU and Telescope | hw051 | 50000 | 3 | No | Good |
RUN WITH SVD3 plus telescope
EUDET Run 51
Mimosa Threshold 7
Pos 3: x=38.6 mm, y=84 mm |
41
|
Sun Jun 7 20:03:31 2015 |
Thomas Bergauer | SVD3 (H6B) | hardware run with TLU and Telescope | hw052 | 50000 | 4 | No | Good |
RUN WITH SVD3 plus telescope
EUDET Run 52
Mimosa Threshold 7
Pos 4: x=130.7 mm, y=84 mm (hits auf APV 2 und (bisschen) 3, (bisschen) 8 und 9, 15 und 16 |
50
|
Mon Jun 8 11:33:24 2015 |
Thomas Bergauer | common | beam profile | | | | | Unknown |
120GeV hadrons, beam config H6A.BELLE.003 |
Attachment 1: Beamprofile.png
|
|
58
|
Mon Jun 8 18:08:49 2015 |
Thomas Bergauer | SVD3 (H6B) | Telescope online monitor | | | | | Unknown |
a working version of the EUDET online monitor (which works also with the FE-I4) is at the following location
~/BELLETEST/eudaq-neu/build/monitors/onlinemon$ ./OnlineMon.exe -sc 0 -f /home/telescope/eudaq/data/run000060.raw |
66
|
Tue Jun 9 10:01:03 2015 |
Lukas Bulla | SVD3 (H6B) | TLU setup info | | | | | Unknown |
Channels:
- Upstream vertical -> channel 0; (bitmask 1)
- Upstream horizontal -> channel 1; (bitmask 2)
- Downstream vertical -> channel 2; (bitmask 4)
- Downstream horizontal ->channel 3; (bitmask 8)
TLU DuT interface:
DUT Interface |
Bitmask |
DAQ |
1 |
1 |
Mimosa (EUDET Telescope) |
2 |
2 |
leer |
3 |
4 |
SVD3 |
4 |
8 |
FE-I4 |
|
Attachment 1: upstream.jpg
|
|
Attachment 2: downstream.jpg
|
|
4
|
Thu Jun 4 14:15:50 2015 |
Hao Yin | Belle II FADC (H6A) | FIR | 001 | | | | Good |
FIR filer and ADC delay with all sensor and telescope.
telescope n-side switched. |
5
|
Thu Jun 4 14:16:20 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 001 | 10000 | | | Good |
FirRun001, room temp
telescope n-side switched. |
6
|
Thu Jun 4 15:12:41 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 001 | 50000 | 1 | No | Good |
PedestalRun001, FIRRun001, room temp
telescope n-side switched.
In order to correct the position change the |
Attachment 1: BW_p-side_001Result.pdf
|
Attachment 2: BW_n-side_001Result.pdf
|
Attachment 3: L6_p-side_001ModProp.pdf
|
Attachment 4: L6_n-side_001ModProp.pdf
|
Attachment 5: L6_p-side_001Result.pdf
|
Attachment 6: L5_p-side_001ModProp.pdf
|
Attachment 7: L6_n-side_001Result.pdf
|
Attachment 8: L5_n-side_001ModProp.pdf
|
Attachment 9: L5_p-side_001Result.pdf
|
Attachment 10: L3_p-side_001ModProp.pdf
|
Attachment 11: L5_n-side_001Result.pdf
|
Attachment 12: L3_p-side_001Result.pdf
|
Attachment 13: L3_n-side_001ModProp.pdf
|
Attachment 14: L3_n-side_001Result.pdf
|
Attachment 15: L4_p-side_001ModProp.pdf
|
Attachment 16: L4_n-side_001ModProp.pdf
|
Attachment 17: L4_p-side_001Result.pdf
|
Attachment 18: L4_n-side_001Result.pdf
|
Attachment 19: BW_p-side_001ModProp.pdf
|
Attachment 20: BW_n-side_001ModProp.pdf
|
7
|
Thu Jun 4 18:44:50 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 002 | 50000 | 2 | No | Good |
room temp, FIRRun001, pedestal run 003 |
Attachment 1: -Z_p-side_002ModProp.pdf
|
Attachment 2: -Z_n-side_002ModProp.pdf
|
Attachment 3: -Z_p-side_002Result.pdf
|
Attachment 4: L6_p-side_002ModProp.pdf
|
Attachment 5: -Z_n-side_002Result.pdf
|
Attachment 6: L6_n-side_002ModProp.pdf
|
Attachment 7: L6_p-side_002Result.pdf
|
Attachment 8: L5_p-side_002ModProp.pdf
|
Attachment 9: L6_n-side_002Result.pdf
|
Attachment 10: L5_n-side_002ModProp.pdf
|
Attachment 11: L5_p-side_002Result.pdf
|
Attachment 12: L3_p-side_002ModProp.pdf
|
Attachment 13: L5_n-side_002Result.pdf
|
Attachment 14: L3_n-side_002ModProp.pdf
|
Attachment 15: L3_p-side_002Result.pdf
|
Attachment 16: L3_n-side_002Result.pdf
|
Attachment 17: L4_p-side_002ModProp.pdf
|
Attachment 18: L4_n-side_002ModProp.pdf
|
Attachment 19: L4_p-side_002Result.pdf
|
8
|
Thu Jun 4 18:45:42 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 003 | 10000 | | | Good |
firrun003, room temp
|
10
|
Thu Jun 4 22:07:16 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 003 | 189k | 3 | No | Good |
CE. pedestal run 003. Fir run 002. Room temp |
Attachment 1: CE_p-side_003ModProp.pdf
|
Attachment 2: L4_n-side_002Result.pdf
|
Attachment 3: CE_n-side_003ModProp.pdf
|
Attachment 4: CE_p-side_003Result.pdf
|
Attachment 5: CE_n-side_003Result.pdf
|
Attachment 6: L6_p-side_003ModProp.pdf
|
Attachment 7: L6_n-side_003ModProp.pdf
|
Attachment 8: L6_p-side_003Result.pdf
|
Attachment 9: L6_n-side_003Result.pdf
|
Attachment 10: L5_p-side_003ModProp.pdf
|
Attachment 11: L5_n-side_003ModProp.pdf
|
Attachment 12: L5_p-side_003Result.pdf
|
Attachment 13: L3_p-side_003ModProp.pdf
|
Attachment 14: L5_n-side_003Result.pdf
|
Attachment 15: L3_n-side_003ModProp.pdf
|
Attachment 16: L3_p-side_003Result.pdf
|
Attachment 17: L3_n-side_003Result.pdf
|
Attachment 18: L4_p-side_003ModProp.pdf
|
Attachment 19: L4_n-side_003ModProp.pdf
|
Attachment 20: L4_p-side_003Result.pdf
|
Attachment 21: L4_n-side_003Result.pdf
|
11
|
Fri Jun 5 08:20:27 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 004 | 50000 | 4 | No | Good |
room temp, FIRRun002, pedestalrun003, taget FW |
Attachment 1: L6_p-side_004ModProp.pdf
|
Attachment 2: -Z_n-side_004ModProp.pdf
|
Attachment 3: L6_p-side_004Result.pdf
|
Attachment 4: L6_n-side_004ModProp.pdf
|
Attachment 5: L5_p-side_004ModProp.pdf
|
Attachment 6: L6_n-side_004Result.pdf
|
Attachment 7: L5_n-side_004ModProp.pdf
|
Attachment 8: L5_p-side_004Result.pdf
|
Attachment 9: L3_p-side_004ModProp.pdf
|
Attachment 10: L5_n-side_004Result.pdf
|
Attachment 11: L3_n-side_004ModProp.pdf
|
Attachment 12: L3_p-side_004Result.pdf
|
Attachment 13: L3_n-side_004Result.pdf
|
Attachment 14: L4_p-side_004ModProp.pdf
|
Attachment 15: L4_n-side_004ModProp.pdf
|
Attachment 16: L4_p-side_004Result.pdf
|
12
|
Fri Jun 5 12:02:29 2015 |
Hao Yin | Belle II FADC (H6A) | Sixlet Calibration | 001 | | | | Good |
room temp max subevent at 2. with lat = 96 |
13
|
Fri Jun 5 12:03:34 2015 |
Hao Yin | Belle II FADC (H6A) | Sixlet Calibration | 002 | | | | Good |
lat = 97 to a greater range of lat scan |
14
|
Fri Jun 5 19:55:00 2015 |
Hao Yin | Belle II FADC (H6A) | Sixlet Calibration | 003 | | | | Unknown |
lat = 98
room temp
pedestalrun 003 |
15
|
Fri Jun 5 19:59:44 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 004 | 10000 | | | Good |
update pedestal values for room temp sixlet runs.
|
16
|
Fri Jun 5 23:38:51 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 005 | 10000 | | | Unknown |
Readjust after cooling box.
room temp, firrun002
|
17
|
Fri Jun 5 23:39:49 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 005 | ~200k | 5 | No | Good |
FIRRun002, pedestalrun005, room temp
Target BW: beam spot at ~ (0 p, 0 n) |
Attachment 1: BW_edge_p-side_005ModProp.pdf
|
Attachment 2: L4_n-side_004Result.pdf
|
Attachment 3: BW_edge_n-side_005ModProp.pdf
|
Attachment 4: BW_edge_p-side_005Result.pdf
|
Attachment 5: BW_edge_n-side_005Result.pdf
|
Attachment 6: L6_p-side_005ModProp.pdf
|
Attachment 7: L6_n-side_005ModProp.pdf
|
Attachment 8: L6_p-side_005Result.pdf
|
Attachment 9: L5_p-side_005ModProp.pdf
|
Attachment 10: L6_n-side_005Result.pdf
|
Attachment 11: L5_n-side_005ModProp.pdf
|
Attachment 12: L5_p-side_005Result.pdf
|
Attachment 13: L3_p-side_005ModProp.pdf
|
Attachment 14: L5_n-side_005Result.pdf
|
Attachment 15: L3_n-side_005ModProp.pdf
|
Attachment 16: L3_p-side_005Result.pdf
|
Attachment 17: L3_n-side_005Result.pdf
|
Attachment 18: L4_p-side_005ModProp.pdf
|
Attachment 19: L4_n-side_005ModProp.pdf
|
Attachment 20: L4_p-side_005Result.pdf
|
Attachment 21: L4_n-side_005Result.pdf
|
18
|
Sat Jun 6 12:43:55 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 006 | 50000 | 6 | No | Good |
FIRRun002, room temp, pedestalrun005,
layout: same as HW 005
target: -z, pos 6 (strip: p-0, n-0);
NOTE: results shown in the attachments has been evaluated with cmc containing 128 strip
|
Attachment 1: -Z_edge_p-side_006ModProp.pdf
|
Attachment 2: -Z_edge_n-side_006ModProp.pdf
|
Attachment 3: -Z_edge_p-side_006Result.pdf
|
Attachment 4: L6_p-side_006ModProp.pdf
|
Attachment 5: -Z_edge_n-side_006Result.pdf
|
Attachment 6: L6_n-side_006ModProp.pdf
|
Attachment 7: L6_p-side_006Result.pdf
|
Attachment 8: L5_p-side_006ModProp.pdf
|
Attachment 9: L6_n-side_006Result.pdf
|
Attachment 10: L5_n-side_006ModProp.pdf
|
Attachment 11: L5_p-side_006Result.pdf
|
Attachment 12: L3_p-side_006ModProp.pdf
|
Attachment 13: L5_n-side_006Result.pdf
|
Attachment 14: L3_n-side_006ModProp.pdf
|
Attachment 15: L3_p-side_006Result.pdf
|
Attachment 16: L3_n-side_006Result.pdf
|
Attachment 17: L4_p-side_006ModProp.pdf
|
Attachment 18: L4_n-side_006ModProp.pdf
|
Attachment 19: L4_p-side_006Result.pdf
|
Attachment 20: L4_n-side_006Result.pdf
|
19
|
Sat Jun 6 14:28:28 2015 |
Hao Yin | Belle II FADC (H6A) | Harware | 007 | 50000 | 7 | No | Good |
room temp, FIRRun002, PedestalRun005, room temp
target: CE, pos 7 (p-0, n-0) |
Attachment 1: CE_edge_p-side_007ModProp.pdf
|
Attachment 2: CE_edge_n-side_007ModProp.pdf
|
Attachment 3: CE_edge_p-side_007Result.pdf
|
Attachment 4: CE_edge_n-side_007Result.pdf
|
Attachment 5: L6_p-side_007ModProp.pdf
|
Attachment 6: L6_n-side_007ModProp.pdf
|
Attachment 7: L6_p-side_007Result.pdf
|
Attachment 8: L5_p-side_007ModProp.pdf
|
Attachment 9: L6_n-side_007Result.pdf
|
Attachment 10: L5_n-side_007ModProp.pdf
|
Attachment 11: L5_p-side_007Result.pdf
|
Attachment 12: L3_p-side_007ModProp.pdf
|
Attachment 13: L5_n-side_007Result.pdf
|
Attachment 14: L3_n-side_007ModProp.pdf
|
Attachment 15: L3_p-side_007Result.pdf
|
Attachment 16: L3_n-side_007Result.pdf
|
Attachment 17: L4_p-side_007ModProp.pdf
|
Attachment 18: L4_n-side_007ModProp.pdf
|
Attachment 19: L4_p-side_007Result.pdf
|
Attachment 20: L4_n-side_007Result.pdf
|
23
|
Sat Jun 6 16:48:41 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 008 | 50000 | 8 | No | Good |
room temp, FIRRun002, PedestalRun005, room temp
target: FW, pos 8 (p-0, n-0) |
Attachment 1: FW_edge_1_p-side_008ModProp.pdf
|
Attachment 2: FW_edge_1_n-side_008ModProp.pdf
|
Attachment 3: FW_edge_1_p-side_008Result.pdf
|
Attachment 4: FW_edge_1_n-side_008Result.pdf
|
Attachment 5: L6_p-side_008ModProp.pdf
|
Attachment 6: L6_n-side_008ModProp.pdf
|
Attachment 7: L6_p-side_008Result.pdf
|
Attachment 8: L5_p-side_008ModProp.pdf
|
Attachment 9: L6_n-side_008Result.pdf
|
Attachment 10: L5_n-side_008ModProp.pdf
|
Attachment 11: L5_p-side_008Result.pdf
|
Attachment 12: L3_p-side_008ModProp.pdf
|
Attachment 13: L5_n-side_008Result.pdf
|
Attachment 14: L3_n-side_008ModProp.pdf
|
Attachment 15: L3_p-side_008Result.pdf
|
Attachment 16: L3_n-side_008Result.pdf
|
Attachment 17: L4_p-side_008ModProp.pdf
|
Attachment 18: L4_n-side_008ModProp.pdf
|
Attachment 19: L4_p-side_008Result.pdf
|
Attachment 20: L4_n-side_008Result.pdf
|
27
|
Sun Jun 7 10:36:38 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 006 | 10000 | | | Unknown |
Cooled, Temp see attachment
FirRun002
|
Attachment 1: Pos1.PNG
|
|
28
|
Sun Jun 7 10:39:56 2015 |
Hao Yin | Belle II FADC (H6A) | Calibration | 002 | | | | Good |
Cooled!
FIRRun002, pedestalrun006; temp see attachment in pedestalrun006
|
34
|
Sun Jun 7 13:19:19 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 010 | | | | Good |
cooled
FIRRun002, PedestalRun006 (temp enty)
target: BW, pos 1 |
35
|
Sun Jun 7 13:21:15 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 011 | 50000 | | | Good |
cooled (see attachment)
FIRRun002, PedestalRun006
target: -Z, pos 2 |
Attachment 1: Pos2.PNG
|
|
38
|
Sun Jun 7 15:59:05 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 012 | 50000 | | | Unknown |
cooled (see attachment)
FIRRun002, PedestalRun006
target: CE, pos 2
cooling box emergency break ... ie about the last 1-10 k not useable. |
Attachment 1: Pos3.PNG
|
|
39
|
Sun Jun 7 20:02:40 2015 |
Hao Yin | Belle II FADC (H6A) | Cooling Box Emergency break | | | | | Unknown |
Something triggered a emergency break. HWRun012 only last 1-10k event has to be discarded. |
43
|
Sun Jun 7 23:04:06 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 013 | 50000 | | | Good |
cooled (see attachment)
FIRRun002, PedestalRun006
target: CE, pos 3
cooling box emergency break ... ie about the last 1-10 k not useable. |
44
|
Sun Jun 7 23:09:29 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 014 | 224k | | | Good |
cooled (see attachment) in - 20,5 out -7,8
FIRRun002, PedestalRun006
target: fw, pos 4 |
Attachment 1: Pos4.png
|
|
47
|
Mon Jun 8 09:21:01 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 015 | 70000 | 8 | Yes | Good |
cooled (see attachment) in - 21 out -18
FIRRun002, PedestalRun006
target: fw, pos 8 |
Attachment 1: Pos8.PNG
|
|
52
|
Mon Jun 8 14:48:27 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 016 | ~96k | 9 | Yes | Good |
cooled (see attachment) in --21.24 out -18-54
FIRRun002, PedestalRun006
target: fw, pos 9 |
59
|
Mon Jun 8 20:13:59 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 017 | | 5 | Yes | Good |
cooled (see attachment) in -21.24 out -18.54
cooling supply emty at ~24:00 ie first 30k is cooled.
FIRRun002, PedestalRun006
target: BW, pos 5 |
62
|
Tue Jun 9 09:32:41 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 007 | 10000 | | | Good |
Room temp, fir002 |
63
|
Tue Jun 9 09:33:33 2015 |
Hao Yin | Belle II FADC (H6A) | Calibration | 003 | | | | Good |
room temp
FIRRun002,
pedestalrun006;
pedestalrun007
|
65
|
Tue Jun 9 09:57:56 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 019 | 62k | 1 | No | Good |
room temp
FIRRun002, PedestalRun007, Calibrationrun003 |
72
|
Tue Jun 9 20:30:37 2015 |
Hao Yin | Belle II FADC (H6A) | FIR | 004 | | | | Good |
FIR filer and ADC delay with all sensor and telescope.
Telescope alignment |
73
|
Tue Jun 9 20:32:46 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 008 | 10000 | | No | Good |
Room temp, fir004 |
74
|
Tue Jun 9 20:36:39 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 020 | 62k | | No | Good |
room temp
FIRRun004, PedestalRun008
telescope alignment |
75
|
Wed Jun 10 10:40:24 2015 |
Hao Yin | Belle II FADC (H6A) | Sixlet Calibration | 004 | | | No | Good |
room temp
pedestalrun 008
FIRRun004
max frame pos = 0. frame
[six]
lvl = 20, 30
lat = 95
sam = 20
grp = 8 |
76
|
Wed Jun 10 11:19:33 2015 |
Hao Yin | Belle II FADC (H6A) | Sixlet Calibration | 005 | | | No | Good |
room temp
pedestalrun 008
FIRRun004
max frame pos = 0. frame
[six]
lvl = 20, 30
lat = 96
sam = 20
grp = 8 |
77
|
Wed Jun 10 12:03:53 2015 |
Hao Yin | Belle II FADC (H6A) | Sixlet Calibration | 006 | | | No | Good |
room temp
pedestalrun 008
FIRRun004
max frame pos = 1-2-3. frame n side still shifted
[six]
lvl = 20, 30
lat = 97
sam = 20
grp = 8 |
78
|
Wed Jun 10 12:04:27 2015 |
Hao Yin | Belle II FADC (H6A) | Sixlet Calibration | 007 | | | No | Good |
room temp
pedestalrun 008
FIRRun004
max frame pos = 1-2-3. frame n side still shifted
[six]
lvl = 20, 30
lat = 98
sam = 20
grp = 8 |
79
|
Wed Jun 10 13:12:33 2015 |
Hao Yin | Belle II FADC (H6A) | Sixlet Calibration | 010 | | | Yes | Good |
cooled
pedestalrun 008
FIRRun004
max frame pos = 1-2-3. frame n side still shifted
[six]
lvl = 15, 35
lat = 96
sam = 50
grp = 8 |
81
|
Wed Jun 10 18:52:34 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 009 | 10000 | | Yes | Good |
temp: in -22 out -18,
FIRRun004, |
Attachment 1: temperature.PNG
|
|
83
|
Wed Jun 10 19:07:42 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 021 | | 5 | Yes | Good |
temp: in -23 out -20
FIRRun002,
PedestalRun010,
Calibrationrun002
taget: BW |
86
|
Thu Jun 11 11:41:50 2015 |
Hao Yin | Belle II FADC (H6A) | Sixlet Calibration | 011 | | | Yes | Good |
cooled
pedestalrun 008
FIRRun004
max frame pos = 1-2-3. frame n side still shifted
[six]
lvl = 15, 35
lat = 96
sam = 50
grp = 8 |
87
|
Thu Jun 11 11:42:39 2015 |
Hao Yin | Belle II FADC (H6A) | Sixlet Calibration | 012 | | | Yes | Good |
cooled until about 400k after that room temp
pedestalrun 009
FIRRun005
sixlet calibration run with only ladders
[six]
lvl = 0, 255
lat = 97
sam = 50
grp = 8 |
89
|
Thu Jun 11 16:35:14 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 022 | | 5 | Yes | Good |
temp: in -23 out -20
FIRRun002,
PedestalRun010,
Calibrationrun002
taget: BW, pos 5 |
90
|
Thu Jun 11 16:38:17 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 023 | | 7 | Yes | Good |
temp: attachment (in 1st col, out 2nd col)
FIRRun002,
PedestalRun010,
Calibrationrun002
taget: CE, pos 7 |
Attachment 1: Pos7.PNG
|
|
92
|
Thu Jun 11 18:01:54 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 024 | | 6 | Yes | Good |
temp: attachment (in 1st col, out 2nd col)
FIRRun002,
PedestalRun010,
Calibrationrun002
taget: -z, pos 6 |
Attachment 1: Pos6.PNG
|
|
93
|
Thu Jun 11 18:37:11 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 025 | | 6 | Yes | Good |
temp: attachment (in 1st col, out 2nd col)
FIRRun002,
PedestalRun010,
Calibrationrun002
taget: ce, pos 3 |
Attachment 1: pos3.PNG
|
|
94
|
Fri Jun 12 09:31:58 2015 |
Hao Yin | Belle II FADC (H6A) | FIR | 005 | | | Yes | Good |
FIR filer and ADC delay for long sixlet cal run. |
96
|
Fri Jun 12 17:00:18 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 011 | 10000 | | No | Good |
cooled pedestal vaules for long sixlet cal |
97
|
Fri Jun 12 17:03:02 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 012 | 10000 | | No | Good |
room temp
FIRRun002
|
99
|
Fri Jun 12 17:11:45 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 026 | 50k | 1 | No | Good |
room temp
FIRRun002,
PedestalRun012,
CalibrationRun003
L3 rotated.
taget: bw, pos 1
|
100
|
Sat Jun 13 09:09:37 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 027 | ~200k | 2 | No | Good |
room temp
FIRRun002,
PedestalRun012,
CalibrationRun003
L3 rotated.
taget: CE, pos 1
|
101
|
Sat Jun 13 10:07:36 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 028 | 50k | 4 | No | Good |
room temp
FIRRun002,
PedestalRun012,
CalibrationRun003
L3 rotated.
taget: FW, pos 4
|
102
|
Sat Jun 13 13:01:39 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 029 | | 3 | No | Good |
room temp
FIRRun002,
PedestalRun012,
CalibrationRun003
L3 rotated.
taget: CE, pos 3
|
107
|
Sat Jun 13 19:26:26 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 030 | | 3 | No | Good |
room temp
FIRRun002,
PedestalRun012,
CalibrationRun003
wo L3 and L4
taget: CE, pos 3
|
108
|
Sat Jun 13 19:29:50 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 030 | | 1 | No | Good |
room temp
FIRRun002,
PedestalRun012,
CalibrationRun003
wo L3 and L4
taget: bw, pos 1
|
1
|
Tue May 12 10:27:39 2015 |
Benedikt Würkner | SVD3 (H6B) | Setup information | | | | | Unknown |
Information concerning the SVD3 setup during a beam test
In the beam area setup the whole crate and the power supply with the usual spider cable and the two Keithly 2410 high voltage supplies. Monitoring of the 2410 happens via a NI MAX interface that connects to the GPIB-Ethernet interface and needs to be configured there. The IP and password are noted on the device. The software can be found on heros in medialib/LONGTERM/longterm R3.1_doubleSided as a normal *.vi file.
Default adresses 16 and 17 as defined in labview, need to figure out on site which is which, if the voltage selected (e.g. 100V) is applied as +50/-50 or if it is applied as +100/-100 before connecting the cables.
Take a run without dut as well to check the telescope integrity. Without dut in beamline!!!!! |
Attachment 1: spider-config.jpg
|
|
2
|
Wed Jun 3 10:48:42 2015 |
Benedikt Würkner | common | Networking | | | | | Unknown |
WLAN Router:
SSID: Hephy
password: 20supersecret14
DHCP Range: 192.168.0.200 to 239
Netmask: /24
DNS Server: 192.168.0.254
Gateway: 192.168.0.254
external IP: 128.141.174.109 (für diverse Port Forwardings)
Manuell vergebene IP Adressen bitte unbedingt Benni mitteilen oder/und in der folgenden Tabelle eintragen!
IP/MAC Zuweisung:
IP |
Machine/Name |
intern |
Port Forwarding (aussen) |
192.168.0.124 |
SVD Kenwood |
VNC(5900) |
VNC(9000) |
192.168.0.11 |
SVD3 DAQ |
VNC(5900) |
VNC(9001) |
192.168.0.12 |
TUX DAQ |
VNC(5900), VNC(5901), SSH(22) |
VNC(9009), VNC(9002), SSH(9003), |
192.168.0.13 |
Belle XY Tisch |
|
|
192.168.0.14 |
TUXOA |
SSH(22), VNC(5900) |
SSH(9004), VNC(9012) |
192.168.0.20 |
JTAG Server |
|
|
192.168.0.148 |
alixcool |
|
|
192.168.0.16 |
slowcontrol |
VNC(5900) |
VNC(9005) |
192.168.0.144 |
CAEN Power supply |
|
|
192.168.0.17 |
zenpixelwiki |
SSH(22), VNC(5900) |
SSH(9006), VNC(9008) |
192.168.0.18 |
TLU (pcx25042, XY) |
VNC(5900) |
VNC(9007) |
192.168.0.19 |
Cooling control PC |
VNC(5900) |
VNC(9011) |
192.168.0.240 |
NI GPIB - ENET / 1000 |
|
|
192.168.0.150 |
Printserver |
VNC(5900) |
VNC(9010) |
|
|
|
|
137.138.113.254 |
Aida PC |
|
vnc(5900) |
Admin Zugang Wlan Router:
IP: 192.168.0.254
Username: admin
password: Hephy2014
|
9
|
Thu Jun 4 18:49:03 2015 |
Benedikt Würkner | SVD3 (H6B) | Setup | | | | | Unknown |
|
Attachment 1: IMG_20150604_184442.jpg
|
|
Attachment 2: IMG_20150604_184451.jpg
|
|
Attachment 3: IMG_20150604_184516.jpg
|
|
20
|
Sat Jun 6 16:14:36 2015 |
Benedikt Würkner | SVD3 (H6B) | calibration run and setup information | cal01 | | | | Unknown |
Calibration Run with +- 50V Bias with higher compliance since the p-side draws more current than expected (23muA by the MAMBO)
|
21
|
Sat Jun 6 16:17:52 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run | hw002 | 5000 | | | Good |
Table: 100:70
Bias: +-50V
Run to confirm trigger delay |
22
|
Sat Jun 6 16:18:48 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run | hw003 | 50000 | | | Unknown |
Table: 100:70
Bias: +-50V
Run to confirm trigger delay |
24
|
Sat Jun 6 21:00:15 2015 |
Benedikt Würkner | SVD3 (H6B) | first hardware run with TLU and Telescope | hw004 | 117171 | | | Unknown |
Table: 100:70
Bias: +-50V
600 pedestal
0 offset (at the beginning)
Started APVDAQ and waited till 600 were taken then started EUDAQ
EUDAQ Run 21
Mimosa Thresholds lvl 6 |
25
|
Sat Jun 6 23:30:29 2015 |
Benedikt Würkner | Belle II FADC (H6A) | Hardware | 009 | | | | Good |
room temp, FIRRun002, PedestalRun005, room temp
target: FW, pos 9 (p-0, n-128*4) |
26
|
Sun Jun 7 00:58:33 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run | hw006 | | | | Crap |
Table: 100:70
Bias: +-50V
600 pedestal
0 offset (at the beginning)
Started APVDAQ and waited till 600 were taken then started EUDAQ
EUDAQ Run 24
Mimosa Thresholds lvl 7 |
29
|
Sun Jun 7 11:38:04 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run with TLU and Telescope | hw007 | 15000 | | | Good |
TLU Run 46
Threshold 8b
Offset 601 |
30
|
Sun Jun 7 12:10:24 2015 |
Benedikt Würkner | SVD3 (H6B) | Telescope Threshold8b test run | 0046 | 14399 | | | Unknown |
Telescope in combination with SVD3 |
31
|
Sun Jun 7 12:11:42 2015 |
Benedikt Würkner | SVD3 (H6B) | Telescope Threshold7 test run | 0047 | 38175 | | | Unknown |
Telescope alone |
32
|
Sun Jun 7 12:12:00 2015 |
Benedikt Würkner | SVD3 (H6B) | Telescope Threshold7 test run | 0048 | 53356 | | | Unknown |
Telescope alone |
33
|
Sun Jun 7 13:18:20 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run with TLU and Telescope | hw008 | 53670 | 1 | No | Good |
FIRST GOOD RUN WITH SVD3 plus telescope
EUDET Run 49
Mimosa Threshold 7
Offset APVDAQ-TLU Event number: 601
Pos 1: x=100 mm, y=79 mm (Hits in APV 3 und 8-9 in p-Seite und 14 und 17 in n-Seite) |
42
|
Sun Jun 7 20:37:56 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run with TLU and Telescope | hw053 | 50000 | 5 | | Good |
RUN WITH SVD3 plus telescope
EUDET Run 53
Mimosa Threshold 6
Pos 5: x=30.5 mm, y= 99.74 mm (wide side top) |
45
|
Sun Jun 7 23:09:46 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run with TLU and Telescope | hw054 | 120000 | 6 | No | Good |
RUN WITH SVD3 plus telescope
EUDET Run 54
Mimosa Threshold 6
Pos 6: x=136.08 mm, y= 91.49 mm (narrow side top) |
46
|
Mon Jun 8 01:28:58 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run with TLU and Telescope | hw055 | 410000 | 7 | No | Good |
RUN WITH SVD3 plus telescope
EUDET Run 55
Mimosa Threshold 6
Pos 7: x= 30.5 mm, y= 79 mm (wide side center) |
48
|
Mon Jun 8 09:37:30 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run with TLU and Telescope | hw056 | 50000 | 8 | No | Good |
RUN WITH SVD3 plus telescope
EUDET Run 56
Mimosa Threshold 6
Pos 8: x=136.08 mm, y= 79 mm (narrow side center) |
Attachment 1: run000056-fitter-residuals.pdf
|
49
|
Mon Jun 8 10:47:44 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run with TLU and Telescope | hw057 | 50000 | 9 | No | Good |
RUN WITH SVD3 plus telescope
EUDET Run 57
Mimosa Threshold 6
Pos 9: x=30.5 mm, y= 60.67 mm (wide side down) |
Attachment 1: run000057-fitter-residuals.pdf
|
51
|
Mon Jun 8 11:57:14 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run with TLU and Telescope | hw058 | 50000 | 10 | No | Good |
RUN WITH SVD3 plus telescope
EUDET Run 58
Mimosa Threshold 6
Pos 10: x= 136.08mm, y=68.9 mm (narrow side down) |
53
|
Mon Jun 8 15:03:53 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run with TLU and FEI4 WORKING | 59 | 19000 | | | Unknown |
Testrun with the FEI4 working for the first time.
Lessons learned about the configuration:
EnableDUTVeto needs to be set for the FEI4 to allow it to work
HandShakeMode needs to be enabled for the FEI4 as well
"Enable RJ45 input during scans" needs to be enabled for the USB-controller |
54
|
Mon Jun 8 15:49:23 2015 |
Benedikt Würkner | SVD3 (H6B) | Hardware FEI4 | 60 | 50000 | 10 | No | Unknown |
Hardware run with FEI4, Telescope and FW&BW Modules
Pos 10: x= 136.08mm, y=68.9 mm (narrow side down)
Bilder: Hitmap FE-I4 und Correlation zw. Mimosa und FE-I4 |
Attachment 1: Screenshot_2015-06-08_17.59.50.png
|
|
Attachment 2: Screenshot_2015-06-08_17.41.03.png
|
|
56
|
Mon Jun 8 16:53:13 2015 |
Benedikt Würkner | SVD3 (H6B) | EUTelescope Fitter not working investigation | | | | | Unknown |
Apparently every problem can be attributed to a misalignment problem. The telescope has troubles with heavily misaligned DUTs. Was resolved by creating different gear-files for each run with pretty precise coordinates of the DUT position calculated for the telescope coordinate system.
Additionally one has to watch out for misaligned planes of the telescope itself. It was required to allow for more than 2mm offset for the telescope planes behind the DUTs. This can be easily checked by looking at the PreAligner plots in the -hitmaker-histo.root file.
It look something like this:
and not like this:
Run number |
offset value |
Comment |
49 |
-1 |
|
50 |
-1 |
Expected default value. EORE=49401 |
51 |
-1 |
Expected default value. EORE=49400 |
52 |
-1 |
Checked -1 EORE= 49401 |
53 |
-1 |
Checked -1 EORE= 49401 |
54 |
-1 |
Checked -1 EORE= 119401, |
55 |
-1 |
Checked -1 EORE= 409388 |
56 |
-1 |
Checked -1 EORE= 49392 |
57 |
-1 |
Checked -1 EORE= 49377 |
58 |
-1 |
Checked -1 EORE= 49397 |
Run |
Position |
x-Table |
x-telescope FW |
x-telescope BW |
49 |
1 |
100 |
-13,7 |
-16,7 |
50 |
2 |
69,3 |
17 |
14 |
51 |
3 |
38,6 |
47,7 |
44,7 |
52 |
4 |
130,7 |
-44,4 |
-47,4 |
53 |
5 |
30,5 |
55,8 |
52,8 |
54 |
6 |
136,8 |
-50,5 |
-53,5 |
55 |
7 |
30,5 |
55,8 |
52,8 |
56 |
8 |
136,8 |
-50,5 |
-53,5 |
57 |
9 |
30,5 |
55,8 |
52,8 |
58 |
10 |
136,8 |
-50,5 |
-53,5 |
|
Attachment 2: bad-alignment.png
|
|
57
|
Mon Jun 8 18:00:06 2015 |
Benedikt Würkner | SVD3 (H6B) | Hardware FEI4 | hw061 | 50000 | 2 | No | Unknown |
RUN WITH SVD3, telescope and FEI4
EUDET Run 61
Mimosa Threshold 6
Pos 2: x=69.3 mm, y=79 mm (Hits in APV 3-4 und 8-9 in p-Seite und 13 und 18 in n-Seite) |
60
|
Mon Jun 8 20:16:41 2015 |
Benedikt Würkner | SVD3 (H6B) | Hardware FEI4 | 62 | 50000 | 3 | No | Unknown |
RUN WITH SVD3, telescope and FEI4
EUDET Run 62
Mimosa Threshold 6
Pos 3: x=38.6 mm, y=84 mm |
61
|
Mon Jun 8 22:11:07 2015 |
Benedikt Würkner | SVD3 (H6B) | Hardware FEI4 | 63 | 490000 | 4 | No | Unknown |
RUN WITH SVD3, telescope and FEI4
EUDET Run 63
Mimosa Threshold 6
Pos 4: x=130.7 mm, y=84 mm |
64
|
Tue Jun 9 09:50:15 2015 |
Benedikt Würkner | SVD3 (H6B) | Hardware FEI4 | 64 | 50000 | 5 | No | Unknown |
RUN WITH SVD3, telescope and FEI4
EUDET Run 64
Mimosa Threshold 6
Pos 5: x=30.5 mm, y= 99.74 mm (wide side top) |
67
|
Tue Jun 9 11:20:25 2015 |
Benedikt Würkner | SVD3 (H6B) | Vertical Beam Profile Run | 65 | 50000 | 2 | No | Unknown |
Trying to get a nice plot of the beam profile by only using the vertical PMTs (number 0 and 2) see http://elog.hephy.at/testbeam-SPS2015/66 for details.
Pos 2: x=69.3 mm, y=79 mm (Hits in APV 3-4 und 8-9 in p-Seite und 13 und 18 in n-Seite)
Producer.TLU Config Change:
|
68
|
Tue Jun 9 12:34:16 2015 |
Benedikt Würkner | SVD3 (H6B) | Horizontal Beam Profile Run | 66 | 50000 | 2 | No | Unknown |
Trying to get a nice plot of the beam profile by only using the PMTs 1 and 3 (horizontal) see http://elog.hephy.at/testbeam-SPS2015/66 for details.
Pos 2: x=69.3 mm, y=79 mm (Hits in APV 3-4 und 8-9 in p-Seite und 13 und 18 in n-Seite)
Producer.TLU Config Change:
|
69
|
Tue Jun 9 14:33:50 2015 |
Benedikt Würkner | SVD3 (H6B) | Vertical Beam Profile Run | 67 | 50000 | 2 | No | Unknown |
Trying to get a nice plot of the beam profile by only using the vertical PMT 0 (upstream vertical, the long one) see http://elog.hephy.at/testbeam-SPS2015/66 for details.
Pos 2: x=69.3 mm, y=79 mm (Hits in APV 3-4 und 8-9 in p-Seite und 13 und 18 in n-Seite)
Producer.TLU Config Change:
|
70
|
Tue Jun 9 16:22:59 2015 |
Benedikt Würkner | SVD3 (H6B) | Beam Profile Results | 66 und 67 | | 2 | No | Good |
|
Attachment 1: HW_066_002_Result.pdf
|
Attachment 2: HW_066_003_Result.pdf
|
Attachment 3: HW_067_000_Result.pdf
|
Attachment 4: HW_067_001_Result.pdf
|
71
|
Tue Jun 9 20:27:55 2015 |
Benedikt Würkner | SVD3 (H6B) | Hardware FEI4 | 68 | 503505 | 8 | No | Unknown |
RUN WITH SVD3, telescope and FEI4
EUDET Run 68
Mimosa Threshold 6
Pos 8: x=136.08 mm, y= 79 mm (narrow side center) |
80
|
Wed Jun 10 18:05:03 2015 |
Benedikt Würkner | SVD3 (H6B) | FEI4 configuration | | | | No | Unknown |
There are two planes, one fixed upstream and one fixed downstream.
CIS3WII_6 upstream and CIS2WI_IBL2 downstream.
They are configured using the pc in H6B which can be accessed via microsoft remote desktop from the network 192.168.5.x using the ip 192.168.5.6.
The configuration files can be found in the folder "E:\ConfigurationCMS\" on the server and are named after the modules.
Only one of the FEI4 detectors can be used at a time since they are of different generations (FEI4A and FEI4B) which can't be used at the same time with the available USB board. vnc
The configuration for EUDAQ needs to be adapted for the used module by changing the name of the configuration file.
[Producer.USBpixI4]
SRAM_READOUT_AT = 5
SkipConfiguration = no
UseSingleBoardConfig = no
boards = 230
modules[230] = 1
#upstream
config_file = E:\ConfigurationCMS\CIS3_W11_06_thr1600_7to21ke_modified.cfg.root
#downstream:
#config_file = E:\ConfigurationCMS\CIS2_W02_IBL1_thr1600_7to14_modified.cfg.root
fpga_firmware = E:\icwiki_svn\USBPixI4\host\tags\release-5.3\config\usbpixi4.bit
lvl1_delay = 16
tlu_trigger_data_delay = 10
In my experience switching between the planes also requires a restart of the USBPix DAQ because apparently something is not working with the reload of a different config file afterwards. I had the phenomenon that the DAQ responded like it was working but the datastream was empty. Therefore always check the online monitor for hitmaps. |
82
|
Wed Jun 10 19:05:04 2015 |
Benedikt Würkner | SVD3 (H6B) | Hardware FEI4 | 71 | 50000 | 1 | No | Unknown |
RUN WITH SVD3, telescope and FEI4
EUDET Run 71
Mimosa Threshold 6
Pos 1: x=100 mm, y=79 mm (Hits in APV 3 und 8-9 in p-Seite und 14 und 17 in n-Seite )
Downstream FEI4 used |
84
|
Wed Jun 10 20:54:36 2015 |
Benedikt Würkner | SVD3 (H6B) | Residuals FE-I4 (Upstream) | 59 | | 10 | No | Good |
|
Attachment 1: run000059-fitter-residuals.pdf
|
85
|
Wed Jun 10 21:36:25 2015 |
Benedikt Würkner | SVD3 (H6B) | Horizontal Beam Profile Run | 72 | 50000 | 1 | No | Good |
Trying to get a nice plot of the beam profile by only using the and 3 (horizontal) see http://elog.hephy.at/testbeam-SPS2015/66 for details.
Pos 1: x=100 mm, y=79 mm (Hits in APV 3 und 8-9 in p-Seite und 14 und 17 in n-Seite )
Producer.TLU Config Change:
|
Attachment 1: HW_072_002_Result.pdf
|
Attachment 2: HW_072_003_Result.pdf
|
Attachment 3: HW_072_000_Result.pdf
|
Attachment 4: HW_072_001_Result.pdf
|
88
|
Thu Jun 11 15:56:32 2015 |
Benedikt Würkner | SVD3 (H6B) | Hardware FEI4 | 73 | 20000 | 7 | No | Unknown |
RUN WITH SVD3, telescope and FEI4
EUDET Run 73
Mimosa Threshold 6
Pos 7: x= 30.5 mm, y= 79 mm (wide side center)
Upstream FEI4 used, checking if alignment change helped |
91
|
Thu Jun 11 17:11:40 2015 |
Benedikt Würkner | SVD3 (H6B) | Hardware FEI4 | 74 | 20000 | 8 | No | Unknown |
RUN WITH SVD3, telescope and FEI4
EUDET Run 74
Mimosa Threshold 6
Pos 8: x=136.08 mm, y= 79 mm (narrow side center)
Upstream FEI4 used |
95
|
Fri Jun 12 16:52:52 2015 |
Benedikt Würkner | SVD3 (H6B) | Telescope without DUT | 76 | ~30k | | No | Good |
Threshold 6
Testrun to see how the telescope behaves without a DUT to test if there is an increased amount of multiple scattering after the aluminum planes of the FW and BW module.
|
Attachment 1: Telescope_without_DUT.png
|
|
98
|
Fri Jun 12 17:08:23 2015 |
Benedikt Würkner | SVD3 (H6B) | Telescope with FEI4 | 80 | ~30k | | No | Good |
Threshold 6
Testrun to see how the telescope behaves without a DUT to test if there is an increased amount of multiple scattering after the aluminum planes of the FW and BW module.
This time with the upstream FEI4 plane |
103
|
Sat Jun 13 16:47:28 2015 |
Benedikt Würkner | SVD3 (H6B) | Mimosa threshold with FEI4 | 82 | 12000 | | No | Good |
Set mimosa threshold to 5 and recorded with FEI4 upstream
L3 already in sensor but not yet configured.
Probably to noisy to help much |
104
|
Sat Jun 13 17:05:35 2015 |
Benedikt Würkner | SVD3 (H6B) | L3 with FEI4 | 84 | 30000 | 1 | No | Good |
L3 sensor at position x: 105, y: 47 hitting apvs: 2&3 on p-side and apv 3 on n-side |
Attachment 1: Telescope_with_L3.png
|
|
105
|
Sat Jun 13 18:02:04 2015 |
Benedikt Würkner | SVD3 (H6B) | L3 with FEI4 | 85 | 70000 | 2 | No | Good |
L3 sensor at position x: 115, y: 47 hitting apvs: 2&3 on p-side and apv 3&4 on n-side |
106
|
Sat Jun 13 19:14:41 2015 |
Benedikt Würkner | SVD3 (H6B) | L3 with FEI4 | 86 | 732000 | 3 | No | Good |
L3 sensor at position x: 115, y: 57 hitting apvs: 1&2 on p-side and apv 3&4 on n-side |