ID |
Date |
Author![up up](up.png) |
Project |
Subject |
Run Number |
Events |
StartTime |
EndTime |
Data |
2
|
Fri Oct 12 19:42:36 2012 |
Christian Irmler | MicronBaby | Configuration of normal stack | | | | | Unknown |
Micron baby stack with all strips connected to APV chips
n-side faces the beam, p-side not read out.
Channels counting from bottom to top
Modules as seen by the beam:
Module name z-position [mm] Sensor ID
COMM-1 0.0 B2Micron_2965_10_baby2
COMM-2 24.7 B2Micron_2965_14_baby2
SPRAY-1 49.4 B2Micron_2825_05_baby3
SPRAY-2 75.5 B2Micron_2825_05_baby4
COMB-1 100.9 B2Micron_2965_10_baby4
COMB-2 135.0 B2Micron_2965_14_baby4
ATOLL-1 159.0 B2Micron_2965_14_baby3
ATOLL-2 183.7 B2Micron_2965_17_baby3 |
Attachment 1: micronbaby_stack_geometry.jpg
|
![micronbaby_stack_geometry.jpg micronbaby_stack_geometry.jpg](../testbeam-SPS12/121012_194157/micronbaby_stack_geometry.jpg) |
3
|
Fri Oct 12 22:00:52 2012 |
Christian Irmler | MicronBaby | cal | cal001 | 83800 | 12.10.2012 21:16:33 | 12.10.2012 21:59:02 | Good |
12.10.2012 21:16:33 event=0 Disk space: Needed=0.00 GB, Available=206.59 GB, Total=931.51 GB
12.10.2012 21:16:33 event=0 DAQ start (mode: Calibration Scan)
12.10.2012 21:16:33 event=0 Init NECO... done
12.10.2012 21:16:34 event=0 Init APVs... done
12.10.2012 21:16:37 event=0 Send 10 dummy triggers to initialize APV pedestals... done
12.10.2012 21:16:37 event=0 Init FADCs... done
12.10.2012 21:16:37 event=0 Taking 600 pedestal events
12.10.2012 21:16:45 event=599 Pedestal and Noise evaluation done - switching to Calibration Scan
12.10.2012 21:17:39 event=2459 rate=8events/s temp/curr=32.7/097.5 32.7/-08.2 32.7/-08.3 32.8/-08.3 31.2/001.6 31.2/001.7 31.2/001.6 31.2/001.4
12.10.2012 21:18:43 event=4023 rate=8events/s temp/curr=32.6/097.3 32.7/-08.2 32.7/-08.5 32.7/-08.3 31.1/001.6 31.1/001.6 31.1/001.6 31.1/001.6
12.10.2012 21:19:49 event=5600 rate=50events/s temp/curr=32.7/097.5 32.6/-08.3 32.6/-08.3 32.6/-08.3 31.1/001.6 31.1/001.6 31.1/001.6 31.1/001.6
12.10.2012 21:20:53 event=7990 rate=7events/s temp/curr=32.6/097.5 32.6/-08.2 32.6/-08.5 32.6/-08.3 31.1/001.6 31.0/001.6 31.1/001.6 31.0/001.6
12.10.2012 21:21:59 event=8694 rate=6events/s temp/curr=32.5/097.3 32.6/-08.2 32.6/-08.5 32.6/-08.3 31.1/001.6 31.0/001.6 31.0/001.6 31.0/001.6
12.10.2012 21:23:02 event=11116 rate=66events/s temp/curr=32.5/097.3 32.6/-08.3 32.5/-08.3 32.5/-08.3 31.0/001.4 31.0/001.7 31.0/001.6 31.0/001.6
12.10.2012 21:24:06 event=13095 rate=7events/s temp/curr=32.5/097.3 32.5/-08.3 32.5/-08.3 32.5/-08.3 31.0/001.6 30.9/001.6 31.0/001.6 31.0/001.6
12.10.2012 21:25:08 event=15105 rate=5events/s temp/curr=32.4/097.5 32.5/-08.3 32.5/-08.3 32.5/-08.3 31.0/001.6 30.9/001.6 30.9/001.6 31.0/001.6
12.10.2012 21:26:13 event=16444 rate=7events/s temp/curr=32.5/097.3 32.4/-08.3 32.4/-08.3 32.5/-08.3 30.9/001.6 30.9/001.6 31.0/001.6 31.0/001.6
12.10.2012 21:27:22 event=18050 rate=6events/s temp/curr=32.4/097.5 32.4/-08.3 32.4/-08.5 32.4/-08.5 30.9/001.6 30.9/001.6 30.9/001.6 30.9/001.6
12.10.2012 21:28:25 event=19878 rate=8events/s temp/curr=32.4/097.3 32.4/-08.3 32.4/-08.3 32.4/-08.3 30.7/001.6 30.9/001.6 30.9/001.6 30.7/001.6
12.10.2012 21:29:26 event=21875 rate=7events/s temp/curr=32.3/097.3 32.3/-08.2 32.4/-08.3 32.3/-08.3 30.7/001.4 30.7/001.6 30.7/001.6 30.7/001.6
12.10.2012 21:30:28 event=24200 rate=50events/s temp/curr=32.3/097.3 32.3/-08.2 32.3/-08.3 32.3/-08.5 30.7/001.6 30.7/001.7 30.7/001.6 30.7/001.6
12.10.2012 21:31:33 event=26300 rate=50events/s temp/curr=32.4/097.5 32.3/-08.2 32.4/-08.3 32.3/-08.3 30.7/001.6 30.7/001.7 30.7/001.6 30.7/001.6
12.10.2012 21:32:41 event=28400 rate=9events/s temp/curr=32.3/097.3 32.3/-08.3 32.2/-08.3 32.3/-08.3 30.7/001.6 30.7/001.6 30.7/001.6 30.6/001.6
12.10.2012 21:33:43 event=30300 rate=50events/s temp/curr=32.3/097.5 32.3/-08.3 32.3/-08.3 32.3/-08.3 30.7/001.6 30.7/001.6 30.7/001.6 30.7/001.6
12.10.2012 21:34:46 event=32242 rate=42events/s temp/curr=32.2/097.5 32.3/-08.3 32.2/-08.5 32.3/-08.3 30.7/001.6 30.7/001.7 30.7/001.6 30.6/001.4
12.10.2012 21:35:50 event=34167 rate=67events/s temp/curr=32.2/097.3 32.3/-08.3 32.2/-08.3 32.2/-08.3 30.7/001.6 30.7/001.6 30.7/001.6 30.7/001.4
12.10.2012 21:36:54 event=35928 rate=7events/s temp/curr=32.2/097.3 32.2/-08.3 32.0/-08.3 32.2/-08.3 30.6/001.4 30.7/001.6 30.7/001.6 30.6/001.4
12.10.2012 21:37:54 event=38470 rate=8events/s temp/curr=32.0/097.5 32.2/-08.3 32.2/-08.3 32.2/-08.3 30.6/001.6 30.6/001.6 30.6/001.6 30.6/001.6
12.10.2012 21:39:00 event=40751 rate=1events/s temp/curr=32.2/097.5 32.2/-08.2 32.2/-08.3 32.2/-08.3 30.6/001.6 30.6/001.6 30.6/001.6 30.6/001.6
12.10.2012 21:40:04 event=42861 rate=7events/s temp/curr=32.2/097.5 32.2/-08.3 32.2/-08.3 32.2/-08.3 30.6/001.6 30.6/001.6 30.6/001.6 30.6/001.6
12.10.2012 21:41:05 event=44950 rate=50events/s temp/curr=32.2/097.5 32.2/-08.2 32.0/-08.3 32.2/-08.3 30.5/001.6 30.6/001.6 30.6/001.6 30.6/001.6
12.10.2012 21:42:10 event=47954 rate=4events/s temp/curr=32.2/097.5 32.2/-08.2 32.2/-08.5 32.2/-08.3 30.5/001.6 30.5/001.6 30.5/001.6 30.5/001.6
12.10.2012 21:43:18 event=49909 rate=7events/s temp/curr=32.2/097.3 32.0/-08.3 32.2/-08.3 32.2/-08.3 30.5/001.6 30.5/001.6 30.6/001.6 30.5/001.6
12.10.2012 21:44:17 event=52950 rate=68events/s temp/curr=32.0/097.3 32.2/-08.3 32.0/-08.3 32.0/-08.3 30.5/001.6 30.5/001.6 30.5/001.6 30.5/001.6
12.10.2012 21:45:17 event=55800 rate=50events/s temp/curr=32.2/097.3 32.2/-08.2 32.2/-08.3 32.2/-08.3 30.4/001.6 30.5/001.6 30.5/001.6 30.5/001.6
12.10.2012 21:46:18 event=59281 rate=31events/s temp/curr=32.2/097.5 32.2/-08.2 32.2/-08.5 32.0/-08.3 30.5/001.6 30.5/001.6 30.5/001.6 30.5/001.6
12.10.2012 21:47:19 event=61723 rate=73events/s temp/curr=32.0/097.5 32.0/-08.2 32.2/-08.5 32.0/-08.3 30.4/001.6 30.5/001.6 30.5/001.6 30.4/001.6
12.10.2012 21:48:20 event=64750 rate=60events/s temp/curr=32.0/097.3 32.2/-08.2 32.0/-08.5 32.0/-08.5 30.5/001.6 30.5/001.6 30.5/001.6 30.4/001.6
12.10.2012 21:49:21 event=66450 rate=50events/s temp/curr=32.0/097.3 32.2/-08.3 32.0/-08.3 32.0/-08.3 30.5/001.6 30.5/001.7 30.4/001.6 30.5/001.6
12.10.2012 21:50:23 event=69850 rate=2events/s temp/curr=32.0/097.5 32.0/-08.3 32.0/-08.5 32.0/-08.3 30.5/001.6 30.4/001.6 30.5/001.6 30.5/001.6
12.10.2012 21:51:23 event=73142 rate=7events/s temp/curr=32.0/097.3 32.2/-08.3 32.0/-08.3 32.0/-08.3 30.4/001.6 30.5/001.6 30.4/001.6 30.4/001.4
12.10.2012 21:52:33 event=74250 rate=5events/s temp/curr=32.0/097.3 31.9/-08.2 32.0/-08.3 32.0/-08.3 30.4/001.6 30.4/001.6 30.4/001.6 30.4/001.6
12.10.2012 21:53:43 event=75006 rate=30events/s temp/curr=32.0/097.3 32.0/-08.3 32.0/-08.3 32.0/-08.3 30.4/001.6 30.4/001.6 30.4/001.6 30.4/001.4
12.10.2012 21:54:45 event=76973 rate=6events/s temp/curr=32.0/097.3 32.0/-08.3 32.0/-08.5 32.0/-08.3 30.4/001.6 30.4/001.6 30.3/001.6 30.4/001.6
12.10.2012 21:55:49 event=78788 rate=6events/s temp/curr=32.0/097.5 31.9/-08.2 31.9/-08.3 32.0/-08.3 30.4/001.6 30.4/001.6 30.3/001.6 30.4/001.6
12.10.2012 21:56:57 event=80261 rate=7events/s temp/curr=32.0/097.5 31.9/-08.2 31.9/-08.3 32.0/-08.3 30.4/001.4 30.4/001.6 30.4/001.6 30.4/001.6
12.10.2012 21:57:58 event=82550 rate=64events/s temp/curr=31.9/097.3 32.0/-08.3 31.9/-08.3 31.9/-08.3 30.4/001.6 30.4/001.6 30.4/001.6 30.3/001.6
12.10.2012 21:58:54 event=83800 Processing calibration data... done
12.10.2012 21:58:55 event=83800 Writing calibration file D:\cern12\micronbaby\data\cal001.cal...done
12.10.2012 21:59:02 event=83800 DAQ stop (mode: Calibration Scan)
12.10.2012 21:59:02 event=83800 Writing properties file D:\cern12\micronbaby\data\cal001.pro...done
|
4
|
Fri Oct 12 23:10:14 2012 |
Christian Irmler | MicronBaby | run | run001 | 333000 | 12.10.2012 23:05:19 | 13.10.2012 06:29:00 | Good |
Micron baby stack
HV = -100V I=5.8uA
beam on
Final DESY position (center of vertical beam profile)
Module position: 0 / +5.0 -- hitting the upper half of the sensor (centered on odd APVs) |
25
|
Tue Oct 16 05:24:21 2012 |
Christian Irmler | MicronOrigami_gross | run ATTENTION: wrong bias voltage | run011 | 150k | 16.10.2012 05:19:28 | 16.10.2012 09:59:24 | Crap |
ATTENTION: Bias voltage was +-100 V instead of +- 50 V
Origami Stack 2: Origami #4, #3, Wedge new1, old
HV = +-100V
Ibias=12.3µA
beam position:
vertical: between APV 1&2 (of 6)
horizontal: centered on APV#3 -> left side of sensor -> wide side of wedge sensors
Position of xy table:
x = 83, y = -25
Temperatures:
Origami #4: In=-33 degC / Out=-34 degC
Origami #3: Out=-35 degC (temperatur sensor of inlet is not working)
Wedge new 1: Out = -17 degC, cooling block = -16 degC
Wedge old: Out = -15 degC, cooling block = -15 degC
Stopped after 132658 events, because of empty gas bottle and thus insufficient cooling. |
26
|
Tue Oct 16 11:07:17 2012 |
Christian Irmler | MicronOrigami_gross | cal | cal006 | 83800 | 16.10.2012 10:30:34 | 16.10.2012 11:00:51 | Unknown |
Origami Stack 2a: Origami #4, Wedge new1
reading out all 6 APV of p-side
HV = +-40V, Ibias=5.12µA
no beam
no cooling |
27
|
Tue Oct 16 11:23:43 2012 |
Christian Irmler | MicronOrigami_gross | run | run012 | 20k | 16.10.2012 11:16:01 | 16.10.2012 12:27:03 | Unknown |
Origami Stack 2a: Origami #4, Wedge new1
reading out all 6 APV of p-side
HV = +-40V, Ibias=10.4µA
Origami 3 and Wedge old are still installed in the box, but not read out --> disconnected
beam:
p-side: centered between APV 4&5
n-side: centered between APV 2&3
--> upper left corner of Origami and wedge module --> we hit the APV chips and / or the PA0 of the Origami module
no cooling
Temperatur sensors:
- T11: Origami #4 in
- T12: Origami #4 out
- T13: Origami #3 in (wrong values!)
- T14: Origami #3 out
- T15: Wedge new 1 out
- T16: Wedge old out
- T17: Wedge new 1 cooling block
- T18: Wedge old cooling block
|
Attachment 1: belle_2a_temperatures.jpg
|
![belle_2a_temperatures.jpg belle_2a_temperatures.jpg](../testbeam-SPS12/121016_112226/belle_2a_temperatures.jpg) |
28
|
Tue Oct 16 13:59:46 2012 |
Christian Irmler | MicronOrigami_gross | run | run013 | 150k | 16.10.2012 13:43:05 | 16.10.2012 20:21:04 | Unknown |
Origami Stack 2: Origami #4, #3, Wedge new1, old
HV = +-50V
Ibias=5.2µA
beam position:
vertical: between APV 1&2 (of 6)
horizontal: centered on APV#3 -> left side of sensor -> wide side of wedge sensors
Position of xy table:
x = 83, y = -31
Temperatur sensors:
- T11: Origami #4 in
- T12: Origami #4 out
- T13: Origami #3 in (wrong values!)
- T14: Origami #3 out
- T15: Wedge new 1 out
- T16: Wedge old out
- T17: Wedge new 1 cooling block
- T18: Wedge old cooling block
|
Attachment 1: belle_2_temperatures.jpg
|
![belle_2_temperatures.jpg belle_2_temperatures.jpg](../testbeam-SPS12/121016_135825/belle_2_temperatures.jpg) |
29
|
Tue Oct 16 22:19:21 2012 |
Christian Irmler | MicronOrigami_gross | cal | cal007 | 83800 | 16.10.2012 20:25:17 | 16.10.2012 21:12:01 | Unknown |
Origami Stack 2: Origami #4, #3, Wedge new1, old
HV = +-50V, Ibias=12.3µA
Position: verticallbtween APV 1&2 of 6, left side of sensor,
wide side of wedge sensors
calibration for run013
Temperatures @ 21:00:
T11: -32 degC
T12: -33 degC
T13: -16 degC (obviously wrong value)
T14: -35 degC
T15: -18 degC
T16: -17 degC
T17: -15 degC
T18: -15 degC |
31
|
Tue Oct 16 23:35:28 2012 |
Christian Irmler | MicronOrigami_gross | run | run014 | 150k | 16.10.2012 23:32:24 | 17.10.2012 04:59:02 | Unknown |
Same as run011, but now with +- 50V bias voltage.
Origami Stack 2: Origami #4, #3, Wedge new1, old
HV = +-10V
Ibias=4.83µA
beam position:
vertical: between APV 1&2 (of 6)
horizontal: centered on APV#1 -> right side of sensor -> small side of wedge sensors
Position of xy table:
x = 23, y = -31
Temperatur sensors:
- T11: Origami #4 in
- T12: Origami #4 out
- T13: Origami #3 in (wrong values!)
- T14: Origami #3 out
- T15: Wedge new 1 out
- T16: Wedge old out
- T17: Wedge new 1 cooling block
- T18: Wedge old cooling block
|
Attachment 1: run014_temperatures.jpg
|
![run014_temperatures.jpg run014_temperatures.jpg](../testbeam-SPS12/121016_233448/run014_temperatures.jpg) |
33
|
Wed Oct 17 05:16:22 2012 |
Christian Irmler | MicronOrigami_gross | run | run015 | 54005 | 17.10.2012 05:10:06 | 17.10.2012 07:27:20 | Unknown |
Origami Stack 2: Origami #4, #3, Wedge new1, old
HV = +-50V
Ibias=4.43µA
beam position:
vertical: between APV 1&2 (of 6)
horizontal: centered on APV#2 -> center of measureable area
Position of xy table:
x = 53, y = -31
Temperatur sensors:
- T11: Origami #4 in
- T12: Origami #4 out
- T13: Origami #3 in (wrong values!)
- T14: Origami #3 out
- T15: Wedge new 1 out
- T16: Wedge old out
- T17: Wedge new 1 cooling block
- T18: Wedge old cooling block
CO2 was empty @ 6 am. |
Attachment 1: run015_temperatures.JPG
|
![run015_temperatures.JPG run015_temperatures.JPG](../testbeam-SPS12/121017_051622/run015_temperatures.JPG) |
60
|
Sat Oct 27 00:43:55 2012 |
Christian Irmler | MicronBaby | cal | cal029 | 83800 | 27.10.2012 00:10:15 | 27.10.2012 00:36:55 | Good |
After irradiation
Micron baby stack after gamma irrdiation
HV = -100 V
I = -58 uA |
61
|
Sat Oct 27 01:13:47 2012 |
Christian Irmler | MicronBaby | run | run029 | 307k | 27.10.2012 01:02:49 | 27.10.2012 07:36:34 | Good |
After irradiation
xy-table: x=319.4, y=74.6
beam hits APV0
Micron baby stack after gamma irrdiation
HV = -100 V
I = -58 uA |
66
|
Sun Oct 28 08:37:53 2012 |
Christian Irmler | MicronOrigami_gross | run | run033 | 66937 | 28.10.2012 08:33:42 | 28.10.2012 14:10:43 | Unknown |
Belle stack 2 after gamma irradiation
HV = +50V -50V
I = 101 uA
CO2 cooling
hitting APV2 (n side) = center of wedge sensor
Temperatur sensors:
- T11: Origami #4 in
- T12: Origami #4 out
- T13: Origami #3 in (still wrong values!)
- T14: Origami #3 out
- T15: Wedge new 1 out
- T16: Wedge old out
- T17: Wedge new 1 cooling block
- T18: Wedge old cooling block
|
Attachment 1: temp_run33.JPG
|
![temp_run33.JPG temp_run33.JPG](../testbeam-SPS12/121028_084620/temp_run33.JPG) |
Attachment 2: temp_run33_2.JPG
|
![temp_run33_2.JPG temp_run33_2.JPG](../testbeam-SPS12/121028_084632/temp_run33_2.JPG) |
68
|
Sun Oct 28 16:22:35 2012 |
Christian Irmler | MicronBaby | run | run034 | 101864 | 28.10.2012 16:12:24 | 28.10.2012 18:34:24 | Good |
Micron Baby stack 2 after irradiation (intermediate strips)
HV = -100 V
I = 36.3 uA
Position APV0 of all sensors
X-Y Table coordinates:
X=0 / Y=-1 (afterwards: nulled)
PC power cut after ~100k events |
78
|
Tue Oct 30 18:35:51 2012 |
Christian Irmler | MicronOrigami_gross | run | run040 | 100k | 30.10.2012 18:23:21 | 30.10.2012 21:55:53 | Unknown |
Cooling for 2DSSD established after some struggle.
2DSSD fully read out with cooling
HV= +40 V -40 V I = 2.1 uA
Beam position:
Origami -z
p-side: APV #5
n-side: APV #13 (= pos.1 of -z)
Positions of thermal sensors:
11 Kapillare Anfang
12 Kapillare Ende
13 ---
14 unmittelbar nach Kapillare
15 Origami in
16 Origami out
17 Origami -z
18 Origami CE
Strip order:
n-Seite: rechts (Salev) nach links (Jura)
p-Seite: oben nach unten
APV chips with lower noise:
-z ce
p-side #5 #10 (= pos 4)
n-side #13 (= pos1) #19 (= pos 3) |
Attachment 1: temperatures_run040.jpg
|
![temperatures_run040.jpg temperatures_run040.jpg](../testbeam-SPS12/121030_183515/temperatures_run040.jpg) |
80
|
Wed Oct 31 15:54:59 2012 |
Christian Irmler | common | Ethernetkabel zu H6A | | | | | Unknown |
Ethernetkabel HNA447 -> H6A:
Das obere Ende im Counting Hut liegt im Zwischenboden unterhalb der orangenen Steckdose beim Eingang mit dem elektronischen Zahlenschloß.
Das untere Ende in der Zone hängt aufgerollt an einem Pfeiler der Kabeltasse, unweit der Stelle an der das Kabel von oben hinunter gelassen wurden. Das ist ewta dort wo die Stiege zu PPE146 endet.
siehe Fotos :) |
Attachment 1: 2012-10-31_15.47.42.jpg
|
![2012-10-31_15.47.42.jpg 2012-10-31_15.47.42.jpg](../testbeam-SPS12/121031_155427/2012-10-31_15.47.42.jpg) |
Attachment 2: 2012-10-31_12.28.32.jpg
|
![2012-10-31_12.28.32.jpg 2012-10-31_12.28.32.jpg](../testbeam-SPS12/121031_160013/2012-10-31_12.28.32.jpg) |
7
|
Sat Oct 13 06:55:47 2012 |
Manfred Valentan | MicronBaby | run | run002 | 234019 | 13.10.2012 06:50:00 | 13.10.2012 13:50:40 | Unknown |
Micron baby stack
HV = -100V I=5.4uA
beam on
Final DESY position (center of vertical beam profile)
Module position: 0 / -13.0 -- hitting the lower half of the sensor (centered on even APVs)
Run interrupted due to RF transmitter fault. |
8
|
Sat Oct 13 14:44:47 2012 |
Manfred Valentan | MicronOrigami_gross | Stack configuration, Belle Stack 3 | | | | | Unknown |
Module in Beamrichtung:
2-DSSD Origami -z
2-DSSD Origami ce
1 Micron Wedge New
1 Micron Wedge Old
n-Seite: Beam abgewand
p-Seite: Beam zugewand
Ausleserichtung Origami:
n-Seite aufsteigend links -> rechts
p-Seite aufsteigend oben -> unten
Ausleserichtung Wedge:
p-Seite: unten -> oben
n-Seite: rechts -> links
Breite Seite der Wedge Sensoren links
Auslese der p-Seite mit 4 APVs:
Origami: Obere 4 APVs (letzte 2 APVs nicht ausgelesen, unten)
Micron: APVs 4,5 nicht ausgelesen (2 obersten)
Micron new: APV0 auf n-Seite I²C - Fehler, APV3 auf p-Seite hat 1/2 Signal
|
9
|
Sat Oct 13 19:04:02 2012 |
Manfred Valentan | MicronOrigami_gross | run with Belle stack 3 | run003 | 30k | 13.10.2012 19:02:31 | | Unknown |
Belle stack 3: 2DSSD-Origami, Wedge_New_1, Wedge_old
HV = +- 50V
I_ges = 11.6 µA
Position of xy table:
x = 49, y = -1
Temperatures at start of run:
Measurement on cooling pipe:
Origami IN: -15,5 degC
Origami OUT = Wedge_New_1 IN: -5,5 degC
Micron_New_1 OUT = Wedge_Old IN: +9,0 degC
Micron_Old OUT: +8.2 degC
Measurement on cooling block
Wedge_New_1: +14.6 degC
Wedge_Old: +18.7 degC
|
13
|
Sun Oct 14 02:00:12 2012 |
Manfred Valentan | MicronBaby | Configuration of intermediate stack | | | | | Unknown |
Micron baby stack with every other strip connected to APV chips
n-side faces the beam, p-side not read out.
Channels counting from bottom to top
Modules as seen by the beam:
Module name z-position [mm] Sensor ID
COMM-I-1 0.0 B2Micron_2965_16_baby2
COMM-I-2 26.0 B2Micron_2965_17_baby2
SPRAY-I-1 50.4 B2Micron_2825_15_baby2 (known issue: I2C-error of APV3)
SPRAY-I-2 76.2 B2Micron_2825_15_baby3
COMB-I-1 101.8 B2Micron_2965_16_baby4
COMB-I-2 136.8 B2Micron_2965_17_baby4
ATOLL-I-1 161.0 B2Micron_2965_10_baby3
ATOLL-I-2 185.3 B2Micron_2965_13_baby3 |