ID |
Date |
Author |
Project |
Subject |
Run Number |
Events |
StartTime |
EndTime |
Data |
29
|
Tue Nov 18 13:13:53 2014 |
Thomas Bergauer | Infineon | hardware run | infineon_run001 | 225508 | | | Unknown |
Infineon new stack - batch 4
single hit
HV=300V, total I = 4.2475 µA
strips horizontal
data file in L:\cern14\infineon\Infineon Run horiz
config file l:\cern14\infineon\Infineon Run horiz\cern14_infineon_single.cfg
STOPPED by main User in H6B (18:11, 15:00)
Events: 225508
Next step: rearange modules vertically
|
98
|
Sat Nov 22 17:00:43 2014 |
Axel König | Infineon | Infineon old | damaged strixel sensors, strange IV behaviour | | | | Unknown |
1.) No events recorded for strixel sensors (run001). They seem to be damaged like they were at DESY.
2.) Very strange IV behaviour for every old Infineon module (especially TB12_baby1). |
65
|
Thu Nov 20 18:15:48 2014 |
Axel König | Infineon | hardware run | Infineon_run013_voltage | 51273 | | | Unknown |
Infineon new stack - batch 4
single hit + eudaq
HV=100V, total I = 3.0326 µA
strips vertical
Table Position: H: 89mm V: 81mm
data file in L:\cern14\infineon\Infineon Run vert
config file l:\cern14\infineon\Infineon Run horiz\cern14_infineon_single.cfg
eudaq file: run000959.raw
--stopped 20.11 // 18:10 --
Eudaq: 54928
Events: 51273 |
61
|
Thu Nov 20 15:46:21 2014 |
Axel König | Infineon | hardware run | Infineon_run012 | 263470 | | | Unknown |
Infineon new stack - batch 4
single hit
HV=300V, total I = ? µA
strips vertical
Table Position: H: 89mm V: 81mm
data file in L:\cern14\infineon\Infineon Run vert
config file l:\cern14\infineon\Infineon Run horiz\cern14_infineon_single.cfg
--stopped 20.11 // 15:30 --
Eudaq: No Events build --> searching for failure
Events: 263470 |
62
|
Thu Nov 20 15:47:56 2014 |
Axel König | Infineon | hardware run | Infineon_run011 | | | | Unknown |
Infineon new stack - batch 4
faulty!!! |
45
|
Wed Nov 19 22:15:41 2014 |
Axel König | Infineon | hardware run | Infineon_run010 | 1498709 | | | Unknown |
Infineon new stack - batch 4
single hit
HV=300V, total I = 4.0200 µA
strips vertical
Table Position: H: 92.5mm V: 81mm
EUDAQ data: Run951 and Run952
data file in L:\cern14\infineon\Infineon Run vert
config file l:\cern14\infineon\Infineon Run horiz\cern14_infineon_multi6.cfg
-- stopped 20.11 / 09:35--
SVD3DAQ Events: 1498709
EUDAQ Events: 2777
EUDAQ stopped counting events --> log entry: "01:38 6-ERROR unexpected trigger number 277714 (expecting 277713)" (TLU Producer) |
44
|
Wed Nov 19 21:56:44 2014 |
Axel König | Infineon | hardware run | Infineon_run008 | 244167 | | | Unknown |
Infineon new stack - batch 4
single hit
HV=300V, total I = 4.0758 µA
strips vertical
Table Position: H: 92.5mm V: 81mm
data file in L:\cern14\infineon\Infineon Run vert
config file l:\cern14\infineon\Infineon Run horiz\cern14_infineon_single.cfg
--stopped 19.11 // 21:53 --
Reason: Want to run the eudaq for the next run
Events: 244167 |
40
|
Wed Nov 19 18:20:29 2014 |
Axel König | Infineon | calibration run | Infineon_run007_cal | | | | Unknown |
|
38
|
Wed Nov 19 09:26:39 2014 |
Axel König | Infineon | hardware run | Infineon_run006 | 1500 | | | Unknown |
Infineon new stack - batch 4
multi hit
HV=300V, total I = 4.0200 µA
strips vertical
Table Position: H: 96mm V: 91mm
data file in L:\cern14\infineon\Infineon Run vert
config file l:\cern14\infineon\Infineon Run horiz\cern14_infineon_multi6.cfg
-- stopped --
1500 Events only --> no trigger signals from TU (01:30 Uhr) |
37
|
Wed Nov 19 00:58:27 2014 |
Axel König | Infineon | hardware run | Infineon_run005 | 87000 | | | Unknown |
Infineon new stack - batch 4
multi hit
HV=300V, total I = 4.0200 µA
strips vertical
Table Position: H: 96mm V: 81mm
data file in L:\cern14\infineon\Infineon Run vert
config file l:\cern14\infineon\Infineon Run horiz\cern14_infineon_multi6.cfg
--stopped 19.11 // 01:00 --
Reason: Enough events, new dut postion for next multi run
Events: 87000 |
36
|
Tue Nov 18 23:04:34 2014 |
Axel König | Infineon | hardware run | Infineon_run004 | 400000 | | | Unknown |
Infineon new stack - batch 4
single hit
HV=300V, total I = 4.0044 µA
strips vertical
Table Position: H: 96mm V: 81mm
data file in L:\cern14\infineon\Infineon Run vert
config file l:\cern14\infineon\Infineon Run horiz\cern14_infineon_single.cfg
--stopped 18.11 // 23:05---
Reason: Enough events, next run with the same position but now multi six
Events: 400000
|
31
|
Tue Nov 18 18:33:31 2014 |
Axel König | Infineon | hardware run | Infineon_run003 | 300000 | | | Unknown |
Infineon new stack - batch 4
single hit
HV=300V, total I = 4.0044 µA
strips vertical
Table Position: H: 96mm V: 101mm
data file in L:\cern14\infineon\Infineon Run vert
config file l:\cern14\infineon\Infineon Run horiz\cern14_infineon_single.cfg
--Stopped 18.11 / 20:20---
Reason: Enough events, adjusting new DUT position for next run
Events: 300000 |
30
|
Tue Nov 18 18:29:55 2014 |
Axel König | Infineon | calibration run | Infineon_run002 | | | | Unknown |
Infineon_run002 is just a calibration run for the vertical positioned sensors.
data file in L:\cern14\infineon\Infineon Run vert
config file l:\cern14\infineon\Infineon Run horiz\cern14_infineon_single.cfg |
107
|
Sun Nov 23 09:32:48 2014 |
Axel König | Infineon | hardware run | Infineon_old_run007 | 63913 | | | Unknown |
Infineon old
multi hit
Voltage=300V, I=10.4028uA
(new table calibration): V:75, H:96.5
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: run000999
DaqEvents: 63913 (-600 ped)
EUDAQ EVENTS: daq events - 600 (+2 offset) |
108
|
Sun Nov 23 09:36:27 2014 |
Axel König | Infineon | hardware run | Infineon_old_run006 | 526562 | | | Unknown |
Infineon old
multi hit
Voltage=300V, I=10.4028uA
(new table calibration): V:75, H:95
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: run000998
DaqEvents: 526562 (-600 ped)
EUDAQ EVENTS: daq events - 600 (+2 offset) |
103
|
Sun Nov 23 00:51:07 2014 |
Axel König | Infineon | hardware run | Infineon_old_run005 | 26569 | | | Unknown |
Infineon old
multi hit
Voltage=300V, I=10.4609uA
(new table calibration): V:75, H:94.5
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: run000997
DaqEvents: 26569 (-600 ped)
EUDAQ EVENTS: daq events - 600 (+2 offset)
|
|
102
|
Sun Nov 23 00:24:15 2014 |
Axel König | Infineon | hardware run | Infineon_old_run004 | 168725 | | | Unknown |
Infineon old
multi hit
Voltage=300V, I=10.6529uA
(new table calibration): V:81, H:88
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: run000996
DaqEvents: 168725 (-600 ped)
EUDAQ EVENTS: daq events - 600 (+2 offset) |
101
|
Sun Nov 23 00:20:41 2014 |
Axel König | Infineon | hardware run | Infineon_old_run003 | 30000 | | | Unknown |
Infineon old
multi hit
Voltage=300V, I=10.9797uA
(new table calibration): V:?, H:?
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: run000994
DaqEvents: 30000 (-600 ped)
EUDAQ EVENTS: daq events - 600 (+2 offset) |
99
|
Sat Nov 22 18:08:03 2014 |
Axel König | Infineon | hardware run | Infineon_old_run002 | 55000 | | | Unknown |
Infineon old
multi hit
Voltage=300V, I=10.9797uA
(new table calibration): V:81mm, H:102mm
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: run000993
DaqEvents: 55000 (-600 ped)
EUDAQ EVENTS: daq events - 600 (+2 offset) |
97
|
Sat Nov 22 16:53:39 2014 |
Axel König | Infineon | Infineon old | Infineon_old_run001 | 55000 | | | Unknown |
Infineon old
multi hit
Voltage=300V, I=10.9797uA
(new table calibration): V:81mm, H:97mm
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: run000992
DaqEvents: 55000 (-600 ped)
EUDAQ EVENTS: daq events - 600 (+2 offset) |
95
|
Sat Nov 22 16:04:05 2014 |
Axel König | Infineon | Infineon old calibration | Infineon_old_calibration | | | | Unknown |
Calibration run
L:\cern14\infineon_old |
90
|
Sat Nov 22 07:56:33 2014 |
Axel König | AIDA | hardware run | AIDA_run013 | 55629 | | | Unknown |
AIDA
multi hit
Voltage=100V, I=5.3417uA
(new table calibration): V:51mm, H:45mm
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: run000990
DaqEvents: 55629 (-600 ped)
EUDAQ EVENTS: 55003
|
|
89
|
Sat Nov 22 00:58:04 2014 |
Axel König | AIDA | hardware run | AIDA_run012 | 276006 | | | Unknown |
AIDA
multi hit
Voltage=100V, I=5.3417uA
(new table calibration): V:51mm, H:70mm
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: run000989
DaqEvents: 276006 (-600 ped)
EUDAQ EVENTS: 275390 |
88
|
Sat Nov 22 00:11:36 2014 |
Axel König | AIDA | hardware run | AIDA_run011 | 24916 | | | Unknown |
AIDA
multi hit
Voltage=100V, I=5.3470uA
(new table calibration): V:71mm, H:80mm
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: run000988
DaqEvents: 24916 (-600 ped)
EUDAQ EVENTS: DAQ events -600 (+1 trigger offset) |
87
|
Fri Nov 21 23:40:10 2014 |
Axel König | AIDA | hardware run | AIDA_run010 | 26329 | | | Unknown |
AIDA
multi hit
Voltage=100V, I=5.3470uA
(new table calibration): V:71mm, H:90mm
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: run000987
DaqEvents: 26329 (-600 ped)
EUDAQ EVENTS: DAQ events -600 (+1 trigger offset)
|
|
86
|
Fri Nov 21 23:34:36 2014 |
Axel König | AIDA | hardware run | AIDA_run009 | 32902 | | | Unknown |
AIDA
multi hit
Voltage=100V, I=5.2190uA
(new table calibration): V:71mm, H:100mm
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: Run000983
--Stopped 21.11 / 19:20--
DaqEvents: 32902 (-600 ped)
EUDAQ EVENTS: DAQ events -600 (+1 trigger offset)
|
|
85
|
Fri Nov 21 23:33:54 2014 |
Axel König | AIDA | hardware run (PC crashed) | AIDA_run008 | --- | | | Unknown |
22:00 SVD3 PC crashed!!! data will be collected. |
82
|
Fri Nov 21 19:25:57 2014 |
Axel König | AIDA | hardware run | AIDA_run007 | 26770 | | | Unknown |
AIDA
multi hit
Voltage=100V, I=5.4357uA
(new table calibration): V:71mm, H:65mm
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: Run000983
--Stopped 21.11 / 19:20--
DaqEvents: 26770 (-600 ped)
EUDAQ EVENTS: 26171 (+1 trigger offset) |
77
|
Fri Nov 21 18:21:45 2014 |
Axel König | AIDA | hardware run | AIDA_run006 | ~1k | | | Unknown |
verwerfen! |
76
|
Fri Nov 21 18:20:47 2014 |
Axel König | AIDA | hardware run | AIDA_run005 | 20045 | | | Unknown |
AIDA
single hit
Voltage=100V, I=5.4357uA
(new table calibration): V:71mm, H:80mm
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: Run000979
--Stopped 21.11 / 12:12--
DaqEvents: 20045 (-600 ped)
EUDAQ EVENTS: ~18k |
75
|
Fri Nov 21 15:37:30 2014 |
Axel König | AIDA | hardware run | AIDA_run004 | 7057 | | | Unknown |
AIDA
single hit
Voltage=100V, I=5.4357uA
(new table calibration): V:71mm, H:80mm
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: Run000977
--Stopped 21.11 / 12:12--
DaqEvents: 7057 (-600 ped)
EUDAQ EVENTS: 4658 (less than Daq) |
70
|
Fri Nov 21 12:14:46 2014 |
Axel König | AIDA | hardware run | AIDA_run003 | 20617 | | | Unknown |
AIDA
single hit
Voltage=100V, I=5.4240uA
(new table calibration): V:66mm, H:74mm
EUDAQ file: Run000965
config: L:\cern14\AIDA
data: L:\cern14\AIDA
--Stopped 21.11 / 12:12--
DaqEvents: 20617 (-600 ped)
EUDAQ EVENTS: 20019 (2 more than DAQ [+2 offset]) |
69
|
Fri Nov 21 11:10:08 2014 |
Axel König | AIDA | hardware run | AIDA_run002 | 211362 | | | Unknown |
AIDA
multi hit
Voltage=100V, I=4.1688uA
(new table calibration): V:56mm, H:96mm
EUDAQ File: Run000962, Run000963, Run000964
config: L:\cern14\AIDA
data: L:\cern14\AIDA
--Stopped 21.11 / 10:30--
DaqEvents: 211362
EUDAQ EVENTS: ca. 41000 |
68
|
Fri Nov 21 01:43:54 2014 |
Axel König | AIDA | calibration run | AIDA_run001_calibration | | | | Unknown |
Calibration run with AIDA DUT.
Single hit |
91
|
Sat Nov 22 10:20:07 2014 |
Axel König | AIDA | calibration run | AIDA_calibration | | | | Unknown |
Calibration run AIDA_calibration
L:\cern14\AIDA |
74
|
Fri Nov 21 15:10:19 2014 |
Benedikt Würkner | | HardwareRun | 15-22 (exept 19) | none | | | Crap |
|
120
|
Sun Nov 23 17:51:44 2014 |
Benedikt Würkner | Belle SVD | HardwareRun | 046 | 100000 | 20:06 | 20:36 | Unknown |
Hardware Run +-60V Bias
Room Temperature
Pedestal 018 (again marked all the bad strips)
Zero Suppressed
|
114
|
Sun Nov 23 12:55:47 2014 |
Benedikt Würkner | Belle SVD | HardwareRun | 045 | 20000 | | | Unknown |
Hardware Run +-50V Bias
Room Temperature
Pedestal 018 (again marked all the bad strips)
Zero Suppressed |
112
|
Sun Nov 23 12:17:59 2014 |
Benedikt Würkner | Belle SVD | HardwareRun | 044 | 20000 | | | Unknown |
Hardware Run +-30V Bias
Room Temperature
Pedestal 017 (again marked all the bad strips)
Zero Suppressed |
111
|
Sun Nov 23 10:51:49 2014 |
Hao Yin | Belle SVD | HardwareRun | 042 | 76863 | | | Unknown |
Hardware Run +-40V Bias
Room Temperature
Pedestal 016
Zero Suppressed |
Attachment 1: Temp_23-11-14.PNG
|
|
106
|
Sun Nov 23 01:37:42 2014 |
Hao Yin | Belle SVD | HardwareRun | 040 | 20000 | 2014-11-23 01:37:00 | | Unknown |
Bias voltage set to +-80V
Pedestal_015 (cooled)
"New" layout with no cooling (CO2 is no more)
Newly set values for APC Delay
New FIR Run 005
Temperature around 30 C
Bias: +-80V |
105
|
Sun Nov 23 01:05:43 2014 |
Hao Yin | Belle SVD | HardwareRun | 039 | 20000 | 2014-11-22 15:18:40 | | Crap |
Cooled down to -20
Bias voltage set to +-80V
Pedestal_013 (cooled)
Noisefile: HardwareRun_036.noi
|
94
|
Sat Nov 22 15:31:49 2014 |
Hao Yin | Belle SVD | HardwareRun | 038 | 43788 | 2014-11-22 15:18:40 | | Unknown |
Cooled down to -20
Bias voltage set to +-60V
Pedestal_013 (cooled)
Noisefile: HardwareRun_036.noi
Zero suppressed |
93
|
Sat Nov 22 11:37:16 2014 |
Benedikt Würkner | Belle SVD | HardwareRun | 036 | 450378 | 2014-11-22 1:00:00 | 2014-11-22 10:27:54 | Unknown |
Not completely cooled since cooling failed at 1:42 in the night
Bias voltage set to +-60V
Some error with event no17 or 18 leading to the data not being easily analysable requiring a hack in TuxOA
Pedestal_013 (cooled)
Noisefile: HardwareRun_036.noi |
Attachment 1: SPS_Testbeam-Temp.xlsx
|
Attachment 2: Screen_Shot_2014-11-22_at_12.41.44.png
|
|
73
|
Fri Nov 21 15:07:24 2014 |
Benedikt Würkner | Belle SVD | HardwareRun | 019 | 150948 | 2014-11-21 02:41:55 | 2014-11-21 10:11:02 | Unknown |
cooled see appendix (FirRun003)
PedestalRun_010
multi 6 Raw Mode
FIFO size increased
L3n deactivated
100000 deadtime (CTRL TRG)
VME Error, overnight run |
110
|
Sun Nov 23 10:32:41 2014 |
Hao Yin | Belle SVD | PedestalRun | 016 | 10000 | | | Unknown |
Pedestal Run
room temperature (30C)
Bias scans planned |
72
|
Fri Nov 21 15:03:08 2014 |
Benedikt Würkner | Belle SVD | HardwareRun | 014 | 989 | | | Unknown |
cooled see appendix (FirRun003)
PedestalRun_010
multi 6 Raw Mode
FIFO size increased
L3n deactivated
100000 deadtime (CTRL TRG)
Zero_suppressed |
71
|
Fri Nov 21 15:02:28 2014 |
Benedikt Würkner | Belle SVD | HardwareRun | 013 | 1433 | | | Unknown |
cooled see appendix (FirRun003)
PedestalRun_010
multi 6 Raw Mode
FIFO size increased
L3n deactivated
100000 deadtime (CTRL TRG)
Zero_suppressed |
84
|
Fri Nov 21 22:08:32 2014 |
Hao Yin | | PedestalRun | 013 | 10000 | | | Unknown |
correct mapping
cooled -25 °C
L3n deactivated
|
66
|
Thu Nov 20 22:11:06 2014 |
Hao Yin | Belle SVD | HardwareRun | 012 | | | | Good |
cooled see appendix (FirRun003)
PedestalRun_009
multi 6 Raw Mode
FIFO size increased |
63
|
Thu Nov 20 16:13:18 2014 |
Hao Yin | Belle SVD | HardwareRun | 011 | | | | Crap |
cooled see appendix (FirRun003)
PedestalRun_009
multi 6 Raw Mode
FIFO size increased
FIFO FULL at event ~27000 |
60
|
Thu Nov 20 15:32:33 2014 |
Hao Yin | | HardwareRun | 010 | | | | Crap |
same as hardware run 009
FIFO FULL ERROR starting at ~event 5000 |
59
|
Thu Nov 20 11:14:19 2014 |
Benedikt Würkner | | HardwareRun_009 | 009 | | | | Crap |
cooling see attachment of FIRRun003
Ped 009
Cal 005
Multi 6 raw mode
L5_n_side out of order
FIFO_FULL_ERROR starting at ~2000 events |
58
|
Thu Nov 20 11:13:44 2014 |
Hao Yin | | HardwareRun_008 | 008 | | | | Crap |
cooled see attachment in FIRRun_003
PedestalRun_009
CalibrationRun_005
zerosuppressed |
121
|
Sun Nov 23 18:26:54 2014 |
Markus Friedl | Belle SVD | HardwareRun | 005 | 60600 | 23.11.2014 18:24:34 | 23.11.2014 | Good |
Hardware run, hitting APVs 2/3 on p-sides, 1/2 on n-sides
EUDAT telescope running with difference of 2 events |
119
|
Sun Nov 23 16:55:37 2014 |
Markus Friedl | Belle SVD | HardwareRun | 004 | 60600 | 23.11.2014 16:51:49 | 23.11.2014 18:23:54 | Good |
Hardware run, hitting APVs 1/2 on p-sides, 1/2 on n-sides
EUDAT telescope running with difference of 2 events |
54
|
Thu Nov 20 10:33:13 2014 |
Benedikt Würkner | Belle SVD | FIRRun and Delay Scan | 003 | | | | Unknown |
Cooled see appendix
with new layout (l3_n-side channels changed and reactivated).
Latest FIRRun |
Attachment 1: Temp_19-11-14.PNG
|
|
118
|
Sun Nov 23 15:13:37 2014 |
Markus Friedl | Belle SVD | HardwareRun | 003 | 100600 | 23.11.2014 14:07:23 | 23.11.2014 16:51:27 | Good |
Hardware run, hitting APVs 0/1 on p-sides, 1/2 on n-sides
EUDAT telescope running with difference of 2 events |
23
|
Tue Nov 18 09:45:59 2014 |
Hao Yin | | FIRRun_002 | 002 | | Tue Nov 18 09:45:58 CET 2014 | | Unknown |
New FIR run after reconecting to original setting. |
14
|
Mon Nov 17 22:21:41 2014 |
Hao Yin | | FIR run | 001 | | Mon Nov 17 22:08:29 CET 2014 | | Good |
Excellent, brilliant run. |
16
|
Mon Nov 17 22:22:56 2014 |
Hao Yin | | PedestalRun_001 | 001 | 10000 | Mon Nov 17 22:22:41 CET 2014 | | Unknown |
At room temperature.
|
17
|
Mon Nov 17 22:28:05 2014 |
Hao Yin | | CalibrationRun | 001 | | Mon Nov 17 22:27:07 CET 2014 | | Unknown |
Noise file from run 001
PedestalRun_001
FIRRun_001
At room temperature
See DelayRun_001
|
18
|
Mon Nov 17 22:28:07 2014 |
Hao Yin | | CalibrationRun | 001 | | Mon Nov 17 22:27:07 CET 2014 | | Unknown |
Noise file from run 001
PedestalRun_001
FIRRun_001
At room temperature
See DelayRun_001
|
19
|
Mon Nov 17 22:28:09 2014 |
Hao Yin | | CalibrationRun | 001 | | Mon Nov 17 22:27:07 CET 2014 | | Unknown |
Noise file from run 001
PedestalRun_001
FIRRun_001
At room temperature
See DelayRun_001
|
116
|
Sun Nov 23 15:09:53 2014 |
Markus Friedl | Belle SVD | PedestalRun | 001 | 10000 | | | Good |
Initial pedestal run with SVD3 setup and WedgeOld, FW993, BW993 (reading out 4 chips on every p-side) |
117
|
Sun Nov 23 15:10:42 2014 |
Markus Friedl | Belle SVD | CalibrationRun | 001 | 83400 | | | Good |
Initial calibration run with SVD3 setup and WedgeOld, FW993, BW993 (reading out 4 chips on every p-side) |
1
|
Fri Nov 14 19:01:27 2014 |
Thomas Bergauer | common | Administrative Procedures for Departure | | | | | Unknown |
Wednesday:
* Transport request starten (I do not need any transport service) von 887 nach Wien. Das triggert automatisch die Radio Protection Leute. Der EDH Request hängt dann bei irgend einem Franzosen. Den bitte anrufen und für Montag mittags einen Termin ausmachen. Es muss alles geschnüffelt werden, was in der Zone war (also nicht im Counting room)
Merchandise-Bestätigung für die Anreise ist im attachment!
Anreise: https://edh.cern.ch/Document/SupplyChain/SHIP/5855845
Abreise: https://edh.cern.ch/Document/SupplyChain/SHIP/5863835
|
Attachment 1: Merchandise-2014.pdf
|
Attachment 2: ankunftsbestaetigung.pdf
|
2
|
Fri Nov 14 19:22:40 2014 |
Martin Kurz | common | ip addresses, portforwarding, wlan | | | | | Unknown |
WLAN Router:
SSID: Hephy
password: 20supersecret14
DHCP Range: 192.168.0.200 to 239
Netmask: /24
DNS Server: 192.168.0.254
Gateway: 192.168.0.254
external IP: 128.141.61.16 (für diverse Port Forwardings)
Manuell vergebene IP Adressen bitte unbedingt Martin Kurz mitteilen oder/und in der folgenden Tabelle eintragen!
IP/MAC Zuweisung:
IP |
Machine/Name |
intern |
Port Forwarding (aussen) |
192.168.0.10 |
SVD Kenwood |
VNC(5900) |
VNC(9000) |
192.168.0.11 |
AIDA DAQ |
VNC(5900) |
VNC(9001) |
192.168.0.12 |
TUX DAQ |
VNC(5900), VNC(5901), SSH(22) |
VNC(9009), VNC(9002), SSH(9003), |
192.168.0.13 |
Belle XY Tisch |
|
|
192.168.0.14 |
TUXOA |
SSH(22) |
SSH(9004) |
192.168.0.15 |
JTAG Server |
|
|
192.168.0.148 |
alixcool |
|
|
192.168.0.16 |
slowcontrol |
VNC(5900) |
VNC(9005) |
192.168.0.144 |
CAEN Power supply |
|
|
192.168.0.17 |
zenpixelwiki |
SSH(22), VNC(5900) |
SSH(9006), VNC(9008) |
192.168.0.18 |
TLU (pcx25042, XY) |
VNC(5900) |
VNC(9007) |
192.168.0.240 |
NI GPIB - ENET / 1000 |
|
|
192.168.0.150 |
Printserver |
VNC(5900) |
VNC(9010) |
|
|
|
|
|
|
|
|
Admin Zugang Wlan Router:
IP: 192.168.0.254
Username: admin
password: Hephy2014
|
3
|
Fri Nov 14 19:47:25 2014 |
Thomas Bergauer | | Telefonnummern | | | | | Unknown |
* CCC (zentraler Beschleuniger-Kontrollraum): 77500
* H6A Controlroom: 76755
* HEPHY-Handy: 16-2471 or +41 76 487 2471 from outside of CERN
* Office in Meyrin: 12-R11: 74592
Hostel-Zimmern:
* Bergi: 79326
* Benni: 60232
* Hao: 70408
Andere Wichtige Leute:
* Beam-Dame: Edda Gschwendner 16-5080
* NA Hallen Verantwortlicher: Michael Jeckel
Lookup Telefonnummern: http://phonebook.cern.ch
|
4
|
Fri Nov 14 19:49:04 2014 |
Florian Buchsteiner | common | Belle Setup | | | | | Unknown |
|
Attachment 1: SPS_2014_Testbeam_-_Belle_Setup-Model.pdf
|
5
|
Fri Nov 14 19:52:12 2014 |
Thomas Bergauer | | important web pages | | | | | Unknown |
SPS Accelerator status: http://op-webtools.web.cern.ch/op-webtools/vistar/vistars.php?usr=SPS1
general Information about the Beam line(s): http://sba.web.cern.ch/sba/ |
6
|
Sat Nov 15 11:36:41 2014 |
Thomas Bergauer | common | Checklist for North Area access | | | | | Unknown |
Checklist for North Area access:
- Dosimeter (http://dosimetry.web.cern.ch/en)
- Helmet and safety shoes (http://gs-dep.web.cern.ch/en/content/stores_hours)
- Access right to H6A control room (request via EDH): Control Room HNA-447 (0887-1-Q45). Activate access right on your CERN access card at one of the validation stations (https://espace.cern.ch/service-access-control/default.aspx)
- For using CERN rental car, request "CERN vehicle driving license (V)" via EDH
- Park in front of bldg. 890. Walk to North Hall (bldg. 887) through bldg. 907. Swipe dosimeter in front of electronic lock next to the entrance door. Turn left inside bldg. 887. Control room Q45 is on the left-hand side of the upper level. Swipe CERN access card in front of electronic lock.
|
7
|
Sat Nov 15 11:37:19 2014 |
Thomas Bergauer | AIDA | List of EUDET Telescope PCs in H6b | | | | | Unknown |
https://twiki.cern.ch/twiki/bin/view/CLIC/ClicPixelDataTakingCERNPS2014 |
8
|
Sat Nov 15 12:41:50 2014 |
Benedikt Würkner | Belle SVD | Discoveries during preliminary sensor tests | | | | | Unknown |
L5_p_side APV #3 faulty signal
L4_n_side APV #2 and #3 faulty signal |
Attachment 1: weird_signal.png
|
|
Attachment 2: faulty-signal-l4_n.png
|
|
Attachment 3: faulty-signal_l4_n_2.png
|
|
9
|
Sun Nov 16 14:22:51 2014 |
Thomas Bergauer | AIDA | PC Configuration EUDET Telescope in H6b | | | | | Unknown |
PC (gehört AIDA) in H6b control room: ssh telescope@pcaidatb.cern.ch
|
10
|
Sun Nov 16 21:37:56 2014 |
Hao Yin | common | AIM | | | | | Unknown |
fachi: aimhephy@antispam.e4ward.com
chrisu: gargamel0971
flo: flo.bux@sbg.at
shorty: martin@kurznet.net
markus; mueffi1040
hao: hao.yin@gmx.at
benni: benedikt.wuerkner@assoc.oeaw.ac.at
juan: juan.garcia.ferrero@cern.ch
axel: ???
bergi: callmebergi |
11
|
Mon Nov 17 19:23:57 2014 |
Thomas Bergauer | Infineon | PI XY table initial position | | | | | Unknown |
initial position of Infineon Stack (PI Micromove):
(guess center position by eye)
STRIPS IN HORIZONTAL DIRECTION
* vertical axis: M511.DD: Zero position 81.0mm / higher values correspond to lowering the table
* vertical axis: M521.DD: Zero position 96.0mm / higher values correspond to move the table to the table mounting |
12
|
Mon Nov 17 22:03:02 2014 |
Martin Kurz | common | Drucker | | | | | Unknown |
Drucken über den Printserver (192.168.0.150):
MAC:
direkt über den universellen AirPrint Treiber oder mittels Treiber vom Gerätehersteller drucken.
Einfach nach Druckern suchen. Druckername: CanonMP630 @ higgscms
LINUX:
Eine Datei Names (/etc/cups/client.conf) mit dem Inhalt folgenden Inhalt -ohne Anführungszeichen- erstellen: "ServerName 192.168.0.150"
--> sofort steht der Drucker mit allen richtigen Einstellungen zur Verfügung
Drucken mittels Treiber vom Gerätehersteller ist weiterhin möglich. (wird von CUPS automatisch zur Verfügung gestellt) CUPS URL: "http://192.168.0.150:631/printers/CanonMP630"
WINDOWS:
1.) Unter Start->Einstellungen->Drucker und Faxgeräte links den Punkt “neuen Drucker hinzufügen” auswählen.
2.) In dem sich öffnenden Assistenten die Option “Netzwerkdrucker hinzufügen” auswählen und auf “weiter” klicken.
3.) Zunächst den Punkt “Verbindung mit einem Drucker im Internet herstellen” auswählen und dann die "URL" zum Drucker einfügen.
Name: http://192.168.0.150:631/printers/CanonMP630
|
13
|
Mon Nov 17 22:18:27 2014 |
Hao Yin | Belle SVD | ADC delay scan | | | Mon Nov 17 22:08:29 | | Unknown |
L3-p: 18
L4-p: 36
L5-p: 33
L6-p: 39
L3-n: 18
L4-n: 36
L5-n: 36
L6-n: 35 |
15
|
Mon Nov 17 22:21:50 2014 |
Hao Yin | | Bad APVs | | | Mon Nov 17 22:08:29 CET 2014 | | Unknown |
List with bad APVs:
Crap:
APV 5 L6-p Channel 23
Not working:
L3-n APV 3
|
20
|
Mon Nov 17 23:04:57 2014 |
Hao Yin | Belle SVD | PedestalRun_002 | | 10338 | Mon Nov 17 23:03:03 CET 2014 | | Unknown |
Pedestal run at room temperature.
6 subevents. Noise reference run.
Delay as latest run.
Reference run for bad strips. |
21
|
Tue Nov 18 01:03:18 2014 |
Hao Yin | Belle SVD | Remapped FADC inputs | | | Tue Nov 18 01:03:32 CET 2014 | | Unknown |
We moved the second cable to the third connector on the FADC to match DESY testbeam conditions. |
22
|
Tue Nov 18 01:05:04 2014 |
Hao Yin | Belle SVD | PedestalRun_003 | | | Tue Nov 18 01:03:32 CET 2014 | | Unknown |
New pedestal run after switching the connectors.
At room temperature |
24
|
Tue Nov 18 09:48:53 2014 |
Hao Yin | Belle SVD | PedestalRun_004 | | 10000 | Tue Nov 18 09:48:30 CET 2014 | | Unknown |
At room temperature.
Old delay settings and FIRRun_002
|
25
|
Tue Nov 18 09:51:11 2014 |
Hao Yin | | CalibrationRun_002 | | | Tue Nov 18 09:50:24 CET 2014 | | Unknown |
At room temperature
PedestalRun004
Latest delay settings and FIRRun |
26
|
Tue Nov 18 10:12:25 2014 |
Hao Yin | Belle SVD | 6let PedestalRun_005 | | 10000 | Tue Nov 18 10:11:45 CET 2014 | | Unknown |
At room temperature
Latest delay, FIRRun002.
Check for bad strips. |
27
|
Tue Nov 18 10:26:56 2014 |
Hao Yin | Belle SVD | CalibrationRun_003 | | | Tue Nov 18 10:26:52 CET 2014 | | Unknown |
At room temperature
Latest delay and FIRRun |
28
|
Tue Nov 18 12:35:32 2014 |
Axel König | common | Infineon (4 modules) TLU Settings | | | | | Unknown |
- VNC to 192.168.0.18
- In command line: cd C:\Users\telescope\eudaq\bin
- TLUControl.exe.exe -d 2 -a 11 - i RJ45
Operating with AIDA telescope: TLUControl.exe.exe -d 3 -a 11 - i RJ45
Dut Position (left to right): 11, 06, 05, 07 |
32
|
Tue Nov 18 18:45:01 2014 |
Hao Yin | Belle SVD | Trigger Delay scan | | | Tue Nov 18 18:21:50 CET 2014 | | Unknown |
At room temperature
First run was at: 23 (no track)
TimingRun_001:
Trigger delay: 26
TimingRun_002:
Trigger delay: 29
TimingRun_003:
Trigger delay: 32
TimingRun_004:
Trigger delay: 20
TimingRun_005:
Trigger delay: 17
TimingRun_005:
Trigger delay: 14
Trigger chip delay: 110
|
33
|
Tue Nov 18 20:26:12 2014 |
Hao Yin | Belle SVD | HardwareRun_001 | | | Tue Nov 18 18:21:50 CET 2014 | | Unknown |
At room temperature
Latest ADC scan and FIR run.
Latest CAL.
Position: 0.0, see elog entry. |
35
|
Tue Nov 18 20:42:18 2014 |
Benedikt Würkner | Belle SVD | Coordinates of the DUT | | | | | Unknown |
We set the coordinates trying to put the beam in an area with well working APVs
Peak of course differs for n and p sensors due to their different pitch.
L4-6 n-side Peak around strip 180
L4&6 p-side mean value around strip 380
L5 p-side moved by 4.8mm due to reasons (APV misalignment I think) therefore the peak of the same measurements is moved by 4.8/75µm = 64 strips therefore centered around strip 320
The coordinates of the x-y table were set to 0:0 at this point. Refer to Run Alignment2 for reference data. |
39
|
Wed Nov 19 16:24:25 2014 |
Axel König | common | Running EUDAQ | | | | | Unknown |
Windows PC at Telescope:
0.) JTAG Programming: Chose a threshold file (recommended threshold 5) File: M26TB_Cern_2011.thresh5.mcf--> press start
1.) C:\Users\telescope\Desktop\users\BelleII --> start Mimosa 26 Telescope --> select all six Mimosa's
2.) C:\Users\telescope\Desktop\users\BelleII --> start startEudaq_fullWindows.bat
3.) Use configuration file hephy1 (location: C:\eudaq\conf). Change it according to your TLU settings (DUT mask, AND mask, etc.)
4.) configure
5.) start
x) Online monitor in preparation
Files: Are saved in C:\eudaq\data with internal numbering "run000000xxx.raw" (look at the date and time). [You can connect locally to this folder at HEPHY-SVD PC] |
42
|
Wed Nov 19 20:04:53 2014 |
Hao Yin | Belle SVD | PedestalRun_006 | | | | | Unknown |
Temperature: See attachment
FIRFilterRun_002
Layer 3-n side deactivated, because Hao broke it. |
Attachment 1: Temp_19-11-14.PNG
|
|
43
|
Wed Nov 19 20:07:05 2014 |
Hao Yin | Belle SVD | HardwareRun_002 | | | | | Unknown |
Multi-6 cooled.
See latest Noise, and PedestalRun.
|
46
|
Wed Nov 19 22:25:29 2014 |
Hao Yin | Belle SVD | PedestalRun_008 [CheckLayout] | | | | | Unknown |
cooled (temperature see attachment latest noise run),
latest Noise, FIR settings with the right layout mapping. |
47
|
Wed Nov 19 22:59:24 2014 |
Hao Yin | Belle SVD | CalibrationRun_004 | | | | | Crap |
cooled (see last calibration run)
Latest noise, FIRfilter settings.
Failed due to VME read timeout. |
48
|
Wed Nov 19 23:15:50 2014 |
Hao Yin | Belle SVD | HardwareRun_003 | | | | | Unknown |
cooled, latest noise, cal, PedestalRun.
Rawmode |
49
|
Wed Nov 19 23:31:08 2014 |
Hao Yin | Belle SVD | HardwareRun_004 | | | | | Unknown |
Same as HardwareRun_003 but with ZS. |
50
|
Thu Nov 20 00:52:50 2014 |
Hao Yin | Belle SVD | FIRRun_002 | | | | | Unknown |
cooled with new delay run |
51
|
Thu Nov 20 00:54:21 2014 |
Hao Yin | Belle SVD | PedestalRun_008 | | | | | Unknown |
temp see attachment (von flo)
10000
latest fir filter (002) |
52
|
Thu Nov 20 00:55:14 2014 |
Hao Yin | Belle SVD | HardwareRun_007 | | | | | Unknown |
temp cooled see attachment
last noise run(007)
FIRRun_002
PedestalRun_008
new cal run Raw, test with put fifo full flags |
53
|
Thu Nov 20 10:22:17 2014 |
Markus Friedl | Belle SVD | common | | | | | Unknown |
- Some VME errors occured over night
- Optical fiber changed
- Situation improved
- L3n hybrid could not be configured by I2C
- Plugged cable into the former FWDn slot
- Fully working
|
55
|
Thu Nov 20 10:39:11 2014 |
Benedikt Würkner | Belle SVD | PedestalRun_009 | | | | | Unknown |
cooled see appendix (FIRRun003)
MaxEvents 10000
|
56
|
Thu Nov 20 10:39:13 2014 |
Benedikt Würkner | Belle SVD | PedestalRun_009 | | | | | Unknown |
cooled see appendix (FIRRun003)
MaxEvents 10000
|
57
|
Thu Nov 20 10:41:54 2014 |
Benedikt Würkner | Belle SVD | CalibrationRun_005 | | | | | Unknown |
cooled see appendix (FIRRun_003)
PedestalRun_009 |
64
|
Thu Nov 20 17:16:56 2014 |
Axel König | common | how to run the EUDAQ offline monitor | | | | | Unknown |
YOU need
1.) Folder EUDAQ OFFLINE Monitor
2.) ROOT
Starting:
1.) open command line and chose the path where OfflineMonitor is
2.)Type -i "patch of raw file" -o test.root 100
3.) helpfile typing -h |
67
|
Thu Nov 20 22:12:21 2014 |
Axel König | common | SPS Logbook / SPS Online Monitor | | | | | Unknown |
Logbook: https://ab-dep-op-elogbook.web.cern.ch/ab-dep-op-elogbook/elogbook/secure/eLogbook.php?shiftId=1059325
Monitor: http://op-webtools.web.cern.ch/op-webtools/vistar/vistars.php?usr=SPS1 |
78
|
Fri Nov 21 18:23:05 2014 |
Axel König | common | New Table Calibration | | | | | Unknown |
Nach powercut musste der Tisch neu kalibriert werden. Diese Neukalibration betrifft alle Messungen ab den ersten Messungen vom AIDA Stack. |
79
|
Fri Nov 21 18:35:17 2014 |
Axel König | AIDA | Important: Dockbox Inverter! | | | | | Unknown |
Alle AIDA runs vor run_007 hatten kein Signal auf den Sensoren 5 und 6.
Grund: Inverter auf N Seite war im config file noch an (von Markus behoben).
Runs vor 007 können noch verwendet werden obwohl sensoren 5 und 6 negative Events lieferten (kommt aber auf das negative Limit an). |
80
|
Fri Nov 21 19:05:27 2014 |
Hao Yin | Belle SVD | FIRRun_004 | | | Fri Nov 21 19:05:23 CET 2014 | | Unknown |
New ADC delay scan. cooled, -25 temperature
|
81
|
Fri Nov 21 19:10:09 2014 |
Hao Yin | Belle SVD | CalibrationRun_006 | | | | | Unknown |
cooled, latest ADC delay scan and FIRRun. |
83
|
Fri Nov 21 19:42:36 2014 |
Hao Yin | | HardwareRun_033 | | | | | Good |
L6 are swapped, needs to be corrected later in the offline analysis.
cooled at -25
latest ADC delay and FIRRun
PedestalRun_012
CalibrationRun_006
100k trigger dead time
Need to change L6n apv definition to:
mod = 9,0,1,1,1,m,29,0,0,0,0,0,0,L6_n_side
apv = 9,1,34,3,30,x,0,0,5,1,7,0,0,x
apv = 9,0,36,3,50,x,0,0,5,1,6,0,0,x
apv = 9,3,38,3,30,x,0,0,5,1,9,0,0,x
apv = 9,2,40,3,30,x,0,0,5,1,8,0,0,x
to get the right mapping of the sensor. |
Attachment 1: Temp_21-11-14.PNG
|
|
92
|
Sat Nov 22 11:16:26 2014 |
Markus Friedl | Belle SVD | cooling | | | | | Unknown |
Cooling box plant hung up (I2C error on Alix, persistent after reboot)
Power-cycled cooling plant, now working
Slowly cooling down again |
96
|
Sat Nov 22 16:43:18 2014 |
Axel König | common | table, telescope and dut geometry | | | | | Unknown |
geometry files |
Attachment 1: geometry_table.pdf
|
Attachment 2: geometry_DUT.pdf
|
Attachment 3: geometry_infineon_batch4.pdf
|
Attachment 4: geometry_infineon_old.pdf
|
100
|
Sat Nov 22 19:29:40 2014 |
Axel König | AIDA | DUT Position | | | | | Unknown |
|
Attachment 1: AIDA_DUT_Position.JPG
|
|
109
|
Sun Nov 23 09:49:00 2014 |
Markus Friedl | Belle SVD | cooling | | | | | Unknown |
Saturday evening, the cooling became unstable which indicates the end of the CO2 supply, possibly having a mixture of liquid and gas phases.
Strange oscillations observed for the DUT temperatures until the MF valve was finally turned off close to midnight.
|
Attachment 1: temp_last_night.png
|
|
113
|
Sun Nov 23 12:39:45 2014 |
Axel König | common | PMT's of EUDET (Igor Rubinsky) | | | | | Unknown |
Der zweite PM (entsprechend der Beamrichtung) war von Anfang an nicht angeschlossen an die TLU! Stattdessen war ein Atlas pixel sensor, welcher als 4ter PM fungiert angeschlossen. Genau dieser "PM" hatte 0 counts bei der TLU --> Igor sagt, dass dieser Sensor ("PM") anscheinend keine Versorgungsspannung hatte (~400V). Jetzt baut Igor diesen Atlas Sensor wieder aus und hat bereits den nicht angeschlossenen PM wieder angeschlossen an die TLU. DIeser PM zeigt aber nun zu viele counts. Deshalb behalten wir die AND mask 11 (auch jetzt bei den Belle Modulen). |
115
|
Sun Nov 23 15:07:54 2014 |
Markus Friedl | Belle SVD | common | | | | | Unknown |
Geometry setup of FW/BW:
(all dimensions are in mm and refer to the sensor planes) |
Attachment 1: fwbw_setup.png
|
|