Start 04:09
TRACKER WINDOW
Threshold MPW2: 960mV, Pixel R1 C1
MaxTrigger: 1, Trigger-busy: 25
3 Koinzidenz TLU und Hybrid Modus (2er und 3er Koinzidenz) am MPW

zs_cut geaendert zu 5
 

Start 04:03
TRACKER WINDOW
Threshold MPW2: 960mV, Pixel R1 C1
MaxTrigger: 1, Trigger-busy: 25
3 Koinzidenz TLU und Hybrid Modus (2er und 3er Koinzidenz) am MPW
 

Start 03:19
REAL TRACKING
Threshold MPW2: 960mV, Pixel R1 C1
MaxTrigger: 1, Trigger-busy: 25
2 Koinzidenz TLU und Hybrid Modus (2er und 3er Koinzidenz) am MPW
2k MPW events
 

Start 02:27
REAL TRACKING
Threshold MPW2: 960mV, Pixel R1 C1
MaxTrigger: 1, Trigger-busy: 25
2 Koinzidenz TLU und Hybrid Modus (2er und 3er Koinzidenz) am MPW
3k MPW events
 

Start 01:11
REAL TRACKING
Threshold MPW2: 960mV, Pixel R1 C1
MaxTrigger: 1, Trigger-busy: 25
2 Koinzidenz TLU und Hybrid Modus (2er und 3er Koinzidenz) am MPW
3k MPW events
 

Start 01:08
Threshold MPW2: 960mV, Pixel R1 C1
MaxTrigger: 1, Trigger-busy: 500
2 Koinzidenz TLU und Hybrid Modus (2er und 3er Koinzidenz) am MPW
 

Start 00:xx
Threshold MPW2: 960mV, Pixel R1 C1
MaxTrigger: 1, Trigger-busy: 500
2 Koinzidenz TLU und Hybrid Modus (2er und 3er Koinzidenz) am MPW
Davor: Neue local runs am Tracker (...TLU_92.xml) -> Ab hier verwendet
Run for testing beam only

Start 00:xx
Threshold MPW2: 960mV, Pixel R1 C1
MaxTrigger: 1, Trigger-busy: 500
2 Koinzidenz TLU und Hybrid Modus (2er und 3er Koinzidenz) am MPW
Fill Level der MPW Fifos von 5 auf 1 geaendert

Start 00:41
Threshold MPW2: 960mV, Pixel R1 C1
MaxTrigger: 1, Trigger-busy: 500
2 Koinzidenz TLU und Hybrid Modus (2er und 3er Koinzidenz) am MPW
Producer restartet -> works

Start 00:34
Threshold MPW2: 960mV, Pixel R1 C1
MaxTrigger: 1, Trigger-busy: 500
2 Koinzidenz TLU und 3er Koinzidenz Messmodus am MPW
Testen neue Software: Triggernummer von 2er Koinzidenz modus, Daten von 3er Koinzidenz modus
Forgot to restart Producer

Rate, Beta nominal, factor 10 too high

Start 09:37

SiC setrup had to be rewired (wr0ng polarity somewhere (insert here))

Umstellen:
channel 2: LVDS-Signal vertauschen
channel 2 Referenz: 2.100 V 

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.475V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x = 8
y = 68

Start: 08:34
Range Shifter Out, Filter 1 IN, Filter 2 IN
After that run: Downtime 8:40-10:09

TB 24.4.21

0deg (1cm PMMA)

timing was adjusted and FADC had to be restarted

TB 19.6.21

Start 19:43
rate setting was not set correctly deg20 in combination with setting VII instead of nominal flux deg10
 

Start: 07:26 O(100kHz)

TLU: 6,8M Tracker nur 4 M -> Let's reset FADC

Start 23:56
Threshold MPW2: 1200mV, Pixel R1 C1
MaxTrigger: 1, Trigger-busy: 500
2 Koinzidenz TLU und 3er Koinzidenz Messmodus am MPW

Start 23:54
Threshold MPW2: 1200mV, Pixel R1 C1
MaxTrigger: 1, Trigger-busy: 500
3 Koinzidenz TLU und 3er Koinzidenz Messmodus am MPW

testing for picoscope

Start 23:44
Threshold MPW2: 960mV, Pixel R1 C1
MaxTrigger: 1, Trigger-busy: 500
3 Koinzidenz TLU und 3er Koinzidenz Messmodus am MPW

testing for picoscope

Start 23:43
Threshold MPW2: 960mV, Pixel R1 C1
MaxTrigger: 1, Trigger-busy: 500
2 Koinzidenz TLU und 3er Koinzidenz Messmodus am MPW

MT=1, BSY=50,
setting V steering VII,beam looks centered, but rate and spot looks similar to setting VII, maybe wrong acc setting? --> don't use

Start 23:24
Threshold MPW2: 960mV, Pixel R1 C1
MaxTrigger: 1, Trigger-busy: 500
2 Koinzidenz TLU und 3er Koinzidenz Messmodus am MPW

MT=1, BSY=50,
setting VI steering VII,beam is off again

Start 23:21
Threshold MPW2: 960mV, Pixel R1 C1
MaxTrigger: 1, Trigger-busy: 500
2 Koinzidenz TLU und 2er Koinzidenz Messmodus am MPW
Conclusion: Slowing down Tracker does not help (seen before)

MT=1, BSY=50,
final setting VII
new steering VII +12.5mm x,+13mm y ( -beam direction)

Start 22:55
Threshold MPW2: 960mV, Pixel R1 C1
MaxTrigger: 1, Trigger-busy: 25
3 Koinzidenz TLU und 3er Koinzidenz Messung am MPW

MT=1, BSY=50,
potential setting VII
new steering +12.5mm x,+10mm y ( -beam direction), still off

MT=1, BSY=50,

beam off
potential setting VII
steering setting IV + bigger shift in -y direction

MT=1, BSY=50

beam off
potential setting VII
steering setting IV + shift in -y direction

Rate, factor 10 too high, role ~30kHz instead of 3kHz, Beta nominal

08:34 room request, PC for SiC had to be restarted, trigger were connected as prior to shift

Start 08:53
rate looks fine

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.475V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

verändere Position, ab 7:49 bei Aufnahme von Waveforms Position:

x = 0
y = 0

7:51 verändere Position

7:58 neue Position:
x = 8
y = 68

FPGA shutdown --> Datenaufzeichnung bis etwa 8:27, ab dann Suchen des Fehlers

Start: 08:20
Range Shifter Out, Filter 1 IN, Filter 2 IN

TB 19.6.21

Start 19:16
Mean rate O(MHz)
 

Start: 07:20 O(100kHz)

short run for uploading to analysis

MT=1, BSY=50

beam off
potential setting VII
steering setting IV + 1cm in +y direction

Start 22:23 (Run79), 22:30, 22:37, 22:43 

Synchronization: Playing around with trgger_busy (range 25-500) This slows down Eventrate, but does not solve our issue of not being able to count all overflows. (This depends on the ratio of events hitting the MPW2 only, NOT on the overall busy rate)

MT=1, BSY=50,

beam off
potential setting VII
steering setting IV + 1cm in +y direction

Energy Scan
03:06-5:18
MHz Rate
Danach: Abbauen

MT=1, BSY=50,

beam off
potential setting VII
steering setting IV

Start xx:xx:

Tracker speed test: 4MHz internal Trigger from TLU -> works.
Tracker Setting: max_trigger=1 and trigger_busy=25. This gives ~20kHz eventrate.

Energy Scan
03:02
4Hz, VII -> MHz ?

MT=1, BSY=50,
setting VI

few outlier, fewer fluctuations
final setting VI
steering setting IV

Start xx:xx:

Tracker speed test: 2MHz internal Trigger from TLU -> works.

Energy Scan
02:48
1-6M Hz!

MT=1, BSY=50,
potential setting VI

few outlier, fewer fluctuations
steering setting IV

Start 20:24:
Final MT=1, final BSY length =600 (2kHz), Trigger latency 41 optimal

HV 500V

Energy Scan
01:54
Filter vermutlich draussen

MT=1, BSY=50,
setting V

spot still centered
quite stable
~120kHz
steering setting IV

Start 20:10:
Final MT=1, final BSY length =600 (2kHz), Trigger latency 41 optimal

HV 500V

Energy Scan
01:35
Filter vermutlich draussen

Start 19:59:
Final MT=1, final BSY length =600 (2kHz), Trigger latency 41 optimal

HV 500V

Energy Scan
01:10
Filter vermutlich draussen

MT=1, BSY=50,
setting IV
 

Start 19:47:
Final MT=1, final BSY length =600 (2kHz), Trigger latency 41 optimal

HV 500V

Energy Scan
00:46
Filter vermutlich draussen

Start 19:35:
Final MT=1, final BSY length =600 (2kHz), Trigger latency 41 optimal

HV 500V

Energy Scan
00:21
Filter vermutlich draussen

Rate, up till now looks like the same

Start 07:40
rate looks fine, however operators mentioned, that CPD data might have been loaded incorrectly-->pause during run and reloaded (07:48), rate seems unchanged

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.475V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x: 0
y: 0 
 

Start: 07:54
Range Shifter Out, Filter 1 IN, Filter 2 IN

TB 19.6.21

Start 18:48
Mean rate O(MHz)
 

Start: 07:13 O(100kHz)

First data run w/ ramon + tracker + MPW3 + monitor connected

MT=1, BSY=50,
setting IV
 

Start 19:14:
Final MT=1, final BSY length =600 (2kHz), Trigger latency 41 optimal

HV 500V

Testrun for Beam
Ripple Filter jumping around

MT=1, BSY=50,
setting IV
 

Start 19:00:
Final MT=1, final BSY length =600 (2kHz), Trigger latency 41 optimal

HV 500V

Testrun for Beam
Davor: Filter-Spiele :D

MT=1, BSY=50,
beam shifted again
max 30kHz, low rate
setting IV
 

Start 18:46:
Final MT=1, final BSY length =600 (2kHz), Trigger latency 41 optimal

HV 700V

Energy Scan SiC Sensor
23:37
30.000 Hz, falsche Rate -> Filter

MT=1, BSY=50,
beam is centered
rate few 100kHz and two peaks in beam profile
setting IV
 

Start 18:33:
Final MT=1, final BSY length =600 (2kHz), Trigger latency 41 optimal

HV 500V

Energy Scan SiC Sensor
23:36
timing zu frueh

MT=1, BSY=50,
beam shifted again
jumps in rate too high
setting IV
 

Start 18:20:
Final MT=1, final BSY length =500 (2kHz), Trigger latency 41 optimal

HV 500V

2er Koinzidenz
Alignment Run SiC
23:21

MT=1, BSY=50,
beam  centered (total correction +12.5mm x (to the left in beam direction) and +7.5 mm y (down in beam direction)

rate between 100Hz and 70 kHz, few 100Hz spills
setting IV
 

Start 18:09:
Final MT=1, final BSY length =500 (2kHz), Trigger latency 41 optimal

HV 200V

2er Koinzidenz
Alignment Run SiC -> Crap, FADCs abgeschmiert

MT=1, BSY=50,
beam almost centered (total correction +15mm x (to the left in beam direction) and +7.5 mm y (down in beam direction)

rate between 100Hz and 70 kHz
setting IV
 

Start 17:58:
Final MT=1, final BSY length =500 (2kHz), Trigger latency 41 optimal

HV 300V

2er Koinzidenz
Tracker only, ALIGNMENT
Danach: Umbau auf SiC (Junctionboard geaendert) fuer SiC Alignment

MT=1, BSY=50,
now correct degrader, beam still off
setting IV
 

Start 17:45:
Final MT=1, final BSY length =500 (2kHz), Trigger latency 41 optimal

HV 400V

2er Koinzidenz
Tracker only, Alignment run -> FADC crashed

wrong degrader setting
setting IV
 

Start 17:44:
Final MT=1, final BSY length =500 (2kHz), Trigger latency 41 optimal
accidentally ZS instead of RAW

HV 400V

2er Koinzidenz
Row 3 Col 4
for Beam

MT=1, BSY=50,
rate few 100Hz
x looks off, y centered now (after -0.25cm in y correction)
setting IV
 

Start 17:30:
Final MT=1, final BSY length =500 (2kHz), Trigger latency 41 optimal
accidentally ZS instead of RAW

HV 300V

3er Koinzidenz
Row 3 Col 4
WINDOW RUN
Trigger-Busy + Max Trigger unkown, check in log-file

Rate

Start 07:16
rate looks fine,

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.475V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x: 0
y: 0 

SiC: man sieht erstmals Signale 

Start: 07:42
Range Shifter Out, Filter 1 IN, Filter 2 IN

TB 24.4.21

0deg (1cm Alu)

TB 19.6.21

Start 18:15
Mean rate O(MHz)
 

Start: 07:07 O(MHz)

~4 MHz particle rate
MPW3 data file size after 5 minutes: 11 GB :-$

Tracker lost data again.
[2022-10-08 08:49:11 CEST]    Error::FADCGbEMerger::Event missmatch
[2022-10-08 08:49:11 CEST]    Error::FADCGbEMerger::Event missmatch
[2022-10-08 08:49:11 CEST]    Error::FADCGbEMerger::Event missmatch
[2022-10-08 08:49:11 CEST]    Error::FADCGbEMerger::Event missmatch
[2022-10-08 08:49:11 CEST]    Warning::UDPUnpacker::Expected package number 1953610, got: 1953990!
 

Sync-Error L5.1.1 and L5.1.2

MT=1, BSY=50,
x is centered now, y looks 0.25cm off
setting IV
 

Start 17:14:
Final MT=1, final BSY length =500 (2kHz), Trigger latency 41 optimal
HV 200 V, accidentally ZS instead of RAW

2er Koinzidenz
Row 3 Col 4
Trigger-Busy + Max Trigger unkown, check in log-file

MT=1, BSY=50,
looks +0.5vcm x, -0.5cm y
rate quite low
setting IV
 

Start 16:50:
Final MT=1, final BSY length =500 (2kHz), Trigger latency 41 optimal

HV 100V

2er Koinzidenz
Row 3 Col 4
Trigger-Busy + Max Trigger unkown, check in log-file

MT=1, BSY=50,
2cm off in +x and +y direction (wrong direction)
setting IV
 

Start 16:46:
Final MT=1, final BSY length =500 (2kHz), Trigger latency 40 (not optimal)

2er Koinzidenz
Row 3 Col 4
Trigger-Busy + Max Trigger unkown, check in log-file

MT=1, BSY=50,
1cm off in +x and +y direction
Setting IV

2er Koinzidenz
Row 3 Col 4
Trigger-Busy: 25, Max Trigger:50

fail MAPTA Sensor, not trigger, only signal with 5s spill 5s pause (spill over time meas), looked similar

2er Koinzidenz
Row 3 Col 4
Trigger-Busy: 23, Max Trigger geaendert

Spotsize

2er Koinzidenz
Row 3 Col 4
Neues Beam Files -> Rate nun richtig.

Spotsize

2er Koinzidenz
Row 3 Col 4
Ramonhuengl ?????? (Handschrift unlesbar)

Spotsize

2er Koinzidenz
Row 3 Col 4
Trigger-Busy: 23, Max Trigger 100 -> Gute Settings!

Spotsize

2er Koinzidenz
Row 3 Col 4
test, neue Beam Data: CPD Data neu geladen

Start 16:15:
Final MT=1, final BSY length =500 (2kHz)

Spotsize

2er Koinzidenz
Row 3 Col 4
test

Rate

Start 07:03
verified if run 1 was reliable-->Same results

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.475V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x: 0
y: 0 

Start: 07:38
Range Shifter Out, Filter 1 IN, Filter 2 IN
Scintillators in front
 

TB 24.4.21

90deg (0.2-1cmAlu)

TB 19.6.21

Start 17:42
Mean rate O(MHz)
 

Start: 07:01 O(MHz)

Fluence loss measurement 11.12.2021

Start 18:17

90deg = all five steps Alu

Tracker latency lat=42

First data run w/ ramon + tracker + MPW3 + monitor connected

Tracker dropped some udp packages, total tracker events 23166448

Spotsize

Spotsize

Spotsize, max T 1 & BSY 50 -> rate zu hoch

Spotsize

ASIC: TH 1320, noisy pixel masekd
BEAM OFF

send to monitor: 10

 

Spotsize

ASIC: TH 1320, noisy pixel masekd
BEAM ON

send to monitor: 10

 

Rate

Start 06:55
reallocated correctly, rate looks similar to old measurements now (kHz ish)

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.475V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x: 0
y: 0 

Start: 07:30
Range Shifter Out, Filter 1 IN, Filter 2 IN
Before the run we went inside to: put scintillators behind the sensors, reset the fpga counters

TB 24.4.21

90deg (0.2-1cmAlu)

TB 19.6.21

Start 17:13

Mean rate O(MHz)
 

Start: 06:54 O(MHz)

Bias voltage Diamond: 500

Bias voltage Si LGAD: -100

From a beam perspective the Diamond detector was the first target, on oscilloscope channel 4, the Si LGAD was the second target connected to oscilloscope channel 1.

Triggering source was the Si LGAD detector.

Data was stored on the HiBPM-Osci-2 NUC under c:\measurements

Fluence loss measurement 11.12.2021

Start 15:15

0deg =1cm Alu

Tracker latency lat=42

RD50-MPW3 monitor connected first

Spotsize

ASIC: TH 1320, noisy pixel masekd
BEAM ON

Warning -> not sure, restart

 

Spotsize

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 1100 V
Noise measurement

ASIC: TH 1325, noisy pixel masekd
BEAM ON

send everything to monitor

Spotsize

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 1100 V

ASIC: TH 1320, noisy pixel masekd
BEAM ON

send everything to monitor

Spotsize

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 800 V

ASIC: TH 1310, noisy pixel masekd
BEAM ON

send everything to monitor

Spotsize

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 600 V

ASIC: TH 1330, noisy pixel masekd
BEAM ON

send everything to monitor

Spotsize

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 400 V

repeat run 32 with noisy pixel masked

ASIC: TH 1330
BEAM ON

Spotsize, trigger stopped

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 400 V

ASIC: TH 1330
BEAM ON

Spotsize

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 600 V

ASIC: TH 1330
BEAM ON

Spotsize

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 800 V

ASIC: TH 1340
BEAM ON

Spotsize ,

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 1100 V

Start: 21.04

reference run 100.4MeV

ASIC: TH 1350
BEAM ON

Rate

Start: 07:00
Range Shifter Out, Filter 1 IN, Filter 2 IN
Scintillators in front

TB 24.4.21
 

0deg (1cm Alu) Profil von Stiege

TB 19.6.21

Start 11:21
paused beam at 13:36
15:40-16:20 ECR source fail--downtime

Mean rate O(MHz)

Start: 06:46 O(MHz)

Bias voltage SiC: 800

Bias voltage Si LGAD: -100

From a beam perspective the SiC detector was the first target, on oscilloscope channel 4, the Si LGAD was the second target connected to oscilloscope channel 1.

Triggering source was the Si LGAD detector. The SiC detector was most probably defective.

Data was stored on the HiBPM-Osci-2 NUC under c:\measurements

Fluence loss measurement 11.12.2021

Tracker latency lat=42

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 1100 V

Start: 19:28

1 cm Alu stair phantom on rotary table (0deg)

ASIC: TH 1350
BEAM OFF

Spotsize 

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 1100 V

Start: 18:00

1 cm Alu stair phantom on rotary table (90deg)

ASIC: TH 1310
BEAM OFF

Spotsize test, nach power cycle

Start: 14:28
Range Shifter Out, Filter 1 IN, Filter 2 IN
Power supply of si-sensor went into compliance, therefore the compliance value was set to 100 uA again
Ende 14:35

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 1100 V

Start: 16:40

1 cm Alu stair phantom on rotary table (90deg--> 0.2-1cm Alu)

ASIC: TH 1310 seems to be okay
BEAM ON all included

Spotsize test, nach power cycle

Start: 14:20
Range Shifter Out, Filter 1 IN, Filter 2 IN

Start: 15:19

1 cm Alu stair phantom on rotary table (0deg--> always 1cm Al in beam)

ASIC: TH 1310 seems to be okay
BEAM ON all included

Rate, Beta nominal, no tracker data

Start: 14:06
Range Shifter Out, Filter 1 IN, Filter 2 IN

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 1100 V

Start: 14:04

Reference run without phantom

ASIC: TH 1310 seems to be okay
BEAM ON all included

2 GUIs started -> New Run

Rate, Beta nominal, no tracker data

Start: 13:57
Range Shifter Out, Filter 1 IN, Filter 2 IN

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 800 V

Start: 13:58

Alignment run without phantom

ASIC: TH 1330
BEAM ON all included

Rate, Beta nominal, suddenly no tracker events

Start 14:18 

14:30 enter room request: abbau and shielding was activated, called RP, removed SiC+Si Setup+Al shielding of DSSDs

Degrader 10, Carbon
Messung bis 14:24

danach neue Aufzeichnung (Hintergrundstrahlung) Start ca 14:25

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.100 V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x = 8
y = 68

Start: 13:36
Range Shifter Out, Filter 1 IN, Filter 2 IN

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 600 V

ASIC: TH 1330
BEAM ON all included

Start 14:08

Degrader 100

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.100 V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x = 8
y = 68

Start: 13:09
Range Shifter Out, Filter 1 IN, Filter 2 IN
Changed compliance values back to 30 uA

3er Koinzidenz
for Beam

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 600 V

Start: 12:00
WET measurement of PMMA slabs also used for TOF-CT (GSI)

5cm PMMA. higher energy for Felix Feichtinger
"Accumalte Charge"

more detailed measurement

ASIC: TH 1330
BEAM OFF, for TH check

only few (1 or 2) pixel fire at a low frequency.

Will use this threshold from now on.

Rate, Beta nominal

Start 13:56

Degrader 50

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.100 V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x = 8
y = 68

Start: 12:41
Range Shifter Out, Filter 1 IN, Filter 2 IN
12:53 went inside to test if sensors are activated

3er Koinzidenz
for Beam

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 800 V

Start: 11:44
WET measurement of PMMA slabs also used for TOF-CT (GSI)

5cm PMMA. higher energy for Felix Feichtinger
"Accumalte Charge"

coarse run

ASIC: TH 1350
BEAM OFF, for TH check

no noise hits

Rate, Beta nominal

Start 13:42

Degrader 10

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.100 V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x = 8
y = 68

Start: 12:25
Range Shifter Out, Filter 1 IN, Filter 2 IN
Changed compliance of both sensors to 100 uA

3er Koinzidenz
for Beam

3er Koinzidenz
for Beam

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 1100 V

Start: 11:24
WET measurement of PMMA slabs also used for TOF-CT (GSI)

5cm PMMA
"Accumalte Charge"

PMMA was activated. Had to wait ~10-15min after measurement

ASIC: TH 1350
BEAM OFF, for TH check

MPW3 monitor not connected --> invalid

Rate

Start 06:47
rate only 10Hz, stopped run, room request and rewired trigger.

NOTE: Problem was caused by operators: Optics were not set correctly after ramping up energy from 62.4 to 252.7, not trigger cable

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.475V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x: 0
y: 0 

Start: 06:45
Range Shifter Out, Filter 1 IN, Filter 2 IN
Scintillators in front

TB 24.4.21
Alignment run

TB 19.6.21

Start 07:51
beam was paused at 10:10

bias run and threshold optimization

mean rate was O(100kHz)

Start: 06:40 O(100kHz)

Bias voltage SiC: 800

Bias voltage Si: -150

From a beam perspective the Si detector was the first target, on oscilloscope  channel 1, SiC was the second target connected to oscilloscope channel 3.

Triggering source was the Si detector.

The compliancy of the SiC SMU triggered after approx. 50% of the events had been acquired after this event the HV for the SiC HV was shut down.

Data was stored on the HiBPM-Osci-2 NUC under c:\measurements

Fluence loss measurement 11.12.2021

Tracker timing wrong, latency too low, peak at 0 --> changed lat from 40 to 41 for next run.

Rate, Beta nominal, ERROR tracker  -> reset TLU

Start 13:40

Degrader 100 
Messung aufgenommen, keine Screenshots

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.100 V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x = 8
y = 68

Start: 12:18
Range Shifter Out, Filter 1 IN, Filter 2 IN
Restart run with same settings

3er Koinzidenz
for Beam

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 600 V

Start: 11:00
WET measurement of PMMA slabs also used for TOF-CT (GSI)

4cm PMMA
"Accumalte Charge"

PMMA was activated. Had to wait ~10-15min after measurement

ASIC: TH 1300 again for verificationn - still too many noise hits
BEAM OFF, for TH check

Rate, now Beta nominal again, looks like old setting 4-6 Mhz

Start 12:39

Neustart der vorherigen Messung

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.100 V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x = 8
y = 68

Start: 11:57
Range Shifter Out, Filter 1 IN, Filter 2 IN
Lost beam at 12:15

2er Koinzidenz
Pix 06, 33, 34
for Beam

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 400 V

Start: 10:30
WET measurement of PMMA slabs also used for TOF-CT (GSI)

3cm PMMA
"Accumalte Charge"

PMMA was activated. Had to wait ~10-15min after measurement

ASIC: TH 1400
BEAM OFF, for TH check

Rate, now Beta 10%, looks like Beta EFE also ~400kHz

Start 11:55
Stopped at 12:05-->acc failure

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.100 V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x = 8
y = 68

Start: 11:46
Range Shifter Out, Filter 1 IN, Filter 2 IN

3er Koinzidenz
Pix 06, 33, 34

TB 20.6.21

Start 20:10
Mean rate O(200MHz)
 

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 1100 V
Trigger SiC

Start: 10:06
WET measurement of PMMA slabs also used for TOF-CT (GSI)

2cm PMMA
"Accumalte Charge"

PMMA was activated. Had to wait ~10-15min after measurement

ASIC: TH 1600 - too high
BEAM OFF, for TH check

Rate, now Beta 10%

Start 11:36

schöne Signale

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.100 V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x = 8
y = 68

Start: 11:38
Range Shifter Out, Filter 1 IN, Filter 2 IN

3er Koinzidenz
Pix 06, 33, 34

TB 20.6.21

Start 19:19
Mean rate O(MHz)
 

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 1000 V
Trigger SiC

Start: 09:38
WET measurement of PMMA slabs also used for TOF-CT (GSI)

1cm PMMA
"Accumalte Charge"

PMMA was activated. Had to wait ~10-15min after measurement

ASIC: TH 1800 - too high, no noise hits
BEAM OFF, for TH check

Rate, now Beta 10%

Start 11:09

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.100 V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x = 8
y = 68

Start: 11:26
Range Shifter Out, Filter 1 IN, Filter 2 IN

3er Koinzidenz
Pix 06, 33, 34

TB 24.4.21

corrected trigger position for fluence loss radiography

0deg (1cm ABS)

TB 20.6.21

Start 18:45
2cm Phantom thickness
Mean rate O(MHz)
for live TOF estimation: TDC3,channel 9 - TDC2,channel9

last sensor did not work

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 800 V
Trigger SiC

Start: 09:14
WET measurement of PMMA slabs also used for TOF-CT (GSI)

reference run
"Accumalte Charge"

ASIC: TH 1300
BEAM OFF, for TH check

Rate, now Beta 10%

Start 10:47

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.100 V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x = 8
y = 68

Start: 11:14
Range Shifter Out, Filter 1 IN, Filter 2 IN

3er Koinzidenz
Pix 06, 33, 34
retry for Run 11 (wrong picodata format)

TB 20.6.21

Start 18:03
1cm Phantom thickness
Mean rate O(MHz)
for live TOF estimation: TDC3,channel 9 - TDC2,channel9

last sensor stopped working
 

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 400 V
Repeat of run 13

Start: 08:55
WET measurement of PMMA slabs also used for TOF-CT (GSI)

reference run (with Arduino Spill Start/Stop logic)
fringes in Bragg peak (trigger not optimal (maybe too much latency with Arduino))--> next measurement with "Accumalte Charge" instead of "Spill Start/Stop"

ASIC: TH 1300

Rate

Start 10:38
no signal in SiC

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.100 V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x = 8
y = 68

Start: 10:31
Range Shifter Out, Filter 1 IN, Filter 2 IN
10:57 went inside to restart the Trenz NUC PC + FPGA

3er Koinzidenz
Pix 06, 33, 34

TB 24.4.21

0deg (1cm ABS)

TB 20.6.21

Start 17:27
3cm Phantom thickness
Mean rate O(MHz)
for live TOF estimation: TDC3,channel 9 - TDC2,channel9
 

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 400 V

Start: 08:30
WET measurement of PMMA slabs also used for TOF-CT (GSI)

coarse run (to find Bragg range

Ratenwechsel

Tracker: latency 42 > timing much better

ASIC: TH 1200

Rate

Start 10:28
polarity now correct

now signal in SiC

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.100 V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x = 8
y = 68

Start: 10:24
Range Shifter Out, Filter 1 IN, Filter 2 IN

2er Koinzidenz
Pix 06, 33, 34
Ratenmessunge fuer spaeteres Tracking

TB 24.4.21

0deg (1cm PMMA)

TB 20.6.21

Start 16:46
0cm Phantom thickness
Mean rate O(MHz)
reference run without phantom
for live TOF estimation: TDC3,channel 9 - TDC2,channel9
 

beamtime on 18.09.2021
CH1: SiC
CH3: Si
Bias_Si: -100 V
Bias_SiC: 400 V
Cividec for SiC

Start: 07:44 O(kHz)

repeat run 9 again ;)

run 11 used for new local runs of tracker - hvcmos_mpw3_20221008_11_TLU_00-000011.xml

tracker seems fine, at least in the beginning

again APV sync errors at the end of the run

Rate, Beta 10% nominal

Start 10:24
polarity now correct
no signal in sic --> energy too low due to scintis

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.100 V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x = 8
y = 68

Start: 10:18
Range Shifter Out, Filter 1 IN, Filter 2 IN
Restarting run with the same settings

3er Koinzidenz
Pix 06, 33, 34

TB 24.4.21

90deg (0.2-1cm PMMA)

TB 20.6.21

Start 15:00 (late handover and copying of data)
5cm Phantom thickness
Mean rate O(MHz)

signal in last 2 LGADs too high (only 52MeV residual energy after 5cm)
 

TB 20.6.21

Start 15:55
5cm Phantom thickness
Mean rate O(MHz)
gain in last 2 layers was adapted
RamonRun 11 was not stopped (beam was still on from previous run)
for live TOF estimation: TDC3,channel 9 - TDC2,channel9
 

01. SiC; 2. Si

Small SiC Signal;
Cividec for SiC

Start: 07:39 O(kHz)

MPW2 ANALOG
Threshold MPW2: 960mV, Pixel R3 C3, Pixel R3 C4, Pixel R0 C1. Pixel R0 C6, danach weiter Pixel bis zum Schichtende
3 Koinzidenz TLU und Hybrid Modus (2er und 3er Koinzidenz) am MPW

1k ADC curves per pixel
 

MPW2 ANALOG
Threshold MPW2: 960mV, Pixel R3 C3, Pixel R3 C4, Pixel R0 C1. Pixel R0 C6
3 Koinzidenz TLU und Hybrid Modus (2er und 3er Koinzidenz) am MPW

1k ADC curves per pixel
 

MPW2 ANALOG
Threshold MPW2: 960mV, Pixel R3 C3, Pixel R3 C4, Pixel R0 C1. Pixel R0 C6
3 Koinzidenz TLU und Hybrid Modus (2er und 3er Koinzidenz) am MPW

1k ADC curves per pixel
 

MPW2 ANALOG
Threshold MPW2: 960mV, Pixel R3 C3, Pixel R3 C4, Pixel R0 C1. Pixel R0 C6
3 Koinzidenz TLU und Hybrid Modus (2er und 3er Koinzidenz) am MPW

1k ADC curves per pixel
 

MPW2 ANALOG
Threshold MPW2: 960mV, Pixel R3 C3, Pixel R3 C4, Pixel R0 C1. Pixel R0 C6
3 Koinzidenz TLU und Hybrid Modus (2er und 3er Koinzidenz) am MPW

1k ADC curves per pixel
 

MPW2 ANALOG
Threshold MPW2: 960mV, Pixel R3 C3, Pixel R3 C4, Pixel R0 C1. Pixel R0 C6
3 Koinzidenz TLU und Hybrid Modus (2er und 3er Koinzidenz) am MPW

1k ADC curves per pixel
 

MPW2 ANALOG
Threshold MPW2: 960mV, Pixel R3 C3, Pixel R3 C4, Pixel R0 C1. Pixel R0 C6
3 Koinzidenz TLU und Hybrid Modus (2er und 3er Koinzidenz) am MPW

1k ADC curves per pixel
 

Threshold MPW2: 960mV, Pixel R3 C3
2 Koinzidenz, for testing beam

Setting switched to analog curve forms (CaR Board ADC + picoscope) - first 2 tracker planes moved outside beam
Threshold MPW2: 960mV, Pixel R3 C3
3 Koinzidenz TLU und Hybrid Modus (2er und 3er Koinzidenz) am MPW

Crap run, MPW did not send data
 

Rate, Beta 10% nominal, now 3kHz

Start 10:10
polarity now correct

Wiederholung von vorher, aber keine Aufnahme von neuen Waveforms

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.100 V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.477V channel 1, 0-Level: 2.315V channel 1

position:

x = 8
y = 68

Start: 10:09
Range Shifter Out, Filter 1 IN, Filter 2 IN
Interrupt run at 10:11 -> trying to deactivate filter from the beam room -> didn't work

3er Koinzidenz
Pix 06, 33, 34

TB 24.4.21

90deg (0.2-1cm PMMA)

TB 19.6.21

Start 21:50

Nominal flux degrader 10: mean rate O(200MHz)
 

01. SiC; 2. Si

Bias 1: 400V; Bias 2: -100 V; SiC with Cividec

Start: 07:33 O(kHz)

repeat run 9

max_trgs: 100

tracker still not working.

Rate,15s spill pause, delay can be set by operator

Start 06:37
rate looks okish. few emtpy spills

2021-02-27, 06:07:

channel 1 : Si upstream
channel 2: SiC downstream

400 V Bias

Referenz: 2.475V channel 2, 0-Level: 2.310V channel 2
Referenz: 2.112V channel 1, 0-Level: 2.315V channel 1

position:

x: 0
y: 0 

2021-02-27, 06:30:

Referenz: 2.477V channel 1
channel 2 unverändert
 

2021-02-27, 06:37:

Setting: 3 

Run 1: 6:37 62.4 MeV, Rate geringer als erwartet 

Start: 06:38
Range Shifter Out, Filter 1 IN, Filter 2 IN
Scintillators in front

TB 24.4.21
Alignment run

TB 19.6.21

Start 06:00
startet with wrong setting at the beginning (6 instead of 5) rate was then corrected, but RaMon was still running.

Final rate: 100kHz setting
07:24: room request: changed channel on board (was not connected to osci)

Start: 06:33 O(kHz)

Bias voltage SiC: 800

Bias voltage Si: -150

From a beam perspective the Si detector was the first target, on oscilloscope  channel 1, SiC was the second target connected to oscilloscope channel 3.

Triggering source was the SiC detector.

Data was stored on the HiBPM-Osci-2 NUC under c:\measurements

Fluence loss measurement 11.12.2021

Start 14:45

Tracker xml file: hvcmos_mpw3_20221008_TLU_00-000053.xml