| ID |
Date |
Author |
Project |
Subject |
Run Number |
Events |
StartTime |
EndTime |
|
31
|
Wed Sep 29 10:30:59 2010 |
Markus Friedl | BELLE | run | run009 | 30000 | 29.09.2010 10:27:27 | 29.09.2010 11:06:35 |
zero suppressed (HIT4) @ FADC
Belle stack: Origami-Micron-Micron-Origami - HIT4
HV=100V, Ibias=28A, beam on
cooling: Origami only, chiller: -25C, Module: -10C
modified I2C settings for cooled modules
centered in both axes
telescope run 20084 |
|
30
|
Wed Sep 29 09:39:33 2010 |
Markus Friedl | BELLE | cal | cal003 | 83800 | 29.09.2010 09:38:00 | |
same as cal002, but now with corrected readout order |
|
25
|
Tue Sep 28 22:07:16 2010 |
Markus Friedl | BELLE | cal | cal002 DO NOT USE -> go to cal003 | 83800 | 28.09.2010 22:01:55 | |
Belle stack (Origami, Micron, Micron, Origami)
now cooling only for Origami, Micron are uncooled
chiller set point: -25°C, measured values on Origami: -10°C
HV=100V, Ibias=38µA, beam off
modified I2C settings for cold modules
temperature monitoring: Origami2 pipes in<->out swapped (to achieve shorter tubes)
PROBLEM: Origami n channels are swapped -> USE cal003 INSTEAD!!! |
|
23
|
Tue Sep 28 15:09:16 2010 |
Markus Friedl | BELLE | run | run005 | 40000 | 28.09.2010 15:07:08 | 28.09.2010 20:20:12 |
previous run stopped due to beam problem (shifted, broad, etc).
now recovered, restarting with same settings.
telescope run: 20080 |
|
22
|
Tue Sep 28 14:48:00 2010 |
Markus Friedl | BELLE | run | run004 | 1755 | 28.09.2010 14:48:28 | 28.09.2010 15:06:31 |
same as before, but now pos 1 is located on the other edge (-48mm from center)
telescope 7 / 30 / 277.5
telescope run 20079 |
|
20
|
Tue Sep 28 13:04:02 2010 |
Markus Friedl | BELLE | run | run003 | 25000 | 28.09.2010 13:00:05 | 28.09.2010 14:41:14 |
now for real (previous run was at wrong position)
all same as run001, except position now still centered on p-strips, but on high edge (last APVs) for n side
position: 103 / 30 / 277.5
corresponds to telescope run 20078 |
|
19
|
Tue Sep 28 12:54:33 2010 |
Markus Friedl | BELLE | run | run002 | | 28.09.2010 12:46:54 | |
same as run001 after shifting x by 48mm
103 / 30 / 277.5 ? unsure after crash of xy stage PC |
|
18
|
Tue Sep 28 03:06:31 2010 |
Markus Friedl | BELLE | run | run001 | 119516 | 28.09.2010 03:06:04 | 28.09.2010 12:18:33 |
first run with complete Belle stack: 2 x Origami, 2 x Micron
HV=100V I=49uA
beam is on
chiller is set to 15°C (module temperature is ~17°C)
both Origamis and both Microns are serially cooled
position:centered in both axes 55 / 30 / 277.5
telescope: run20076 (in zero suppressed mode) |
|
17
|
Tue Sep 28 01:13:57 2010 |
Markus Friedl | BELLE | cal | cal001 | 83800 | 28.09.2010 01:11:20 | |
first intcal with complete Belle stack: 2 x Origami, 2 x Micron
HV=100V I=49uA
beam is on
chiller is set to 15°C (module temperature is ~17°C)
both Origamis and both Microns are serially cooled |
|
29
|
Tue Sep 28 23:29:50 2010 |
Markus Friedl | BELLE | run | run008 | 140000 | 28.09.2010 23:29:01 | 29.09.2010 09:36:58 |
Belle stack: Origami-Micron-Micron-Origami
HV=100V, Ibias=38A, beam on
cooling: Origami only, chiller: -25C, Module: -10C
modified I2C settings for cooled modules
centered again
telescope run 20083 |
| Attachment 1: run008_sensordisplay.jpg
|
 |
| Attachment 2: run008_sensordisplay2.jpg
|
 |
|
28
|
Tue Sep 28 23:24:35 2010 |
Markus Friedl | BELLE | run | run007 | 1460 | 28.09.2010 23:23:29 | 28.09.2010 23:27:54 |
Belle stack: Origami-Micron-Micron-Origami
HV=100V, Ibias=38A, beam on
cooling: Origami only, chiller: -25C, Module: -10C
modified I2C settings for cooled modules
centered again
telescope run 20082
sensor config bug (only relevant for sensor display) found -> stopped |
|
27
|
Tue Sep 28 23:23:47 2010 |
Markus Friedl | BELLE | run | run006 | 2003 | 28.09.2010 23:13:22 | 28.09.2010 23:22:26 |
channels swapped -> stopped |
|
148
|
Thu May 19 11:04:04 2011 |
Manfred Valentan | Micron Baby | DUT4, source run, irrad, postzupf | run119 | 100k | 19.05.2011 10:08:14 | 19.05.2011 10:29:02 |
DUT4: B2Micron_2826_19_baby4 (combined p-stop)
config file: D:/cern10/micronbaby/data_lab/DUT4/postzupf/micronbaby_multi6_irrad_postzupf.cfg
HV=+-50V
90Sr 1mCi ~centered
I_start=141µA
I_end=167µA
Every second bond zupfed... |
| Attachment 1: cal119_goodstrips_apv4.png
|
 |
| Attachment 2: cal119_goodstrips_apv5.png
|
 |
| Attachment 3: run119_all_hits_apv4.png
|
 |
| Attachment 4: run119_all_hits_apv5.png
|
 |
| Attachment 5: cal119_pednoise_apv4.png
|
 |
| Attachment 6: cal119_pednoise_apv5.png
|
 |
|
147
|
Thu May 19 11:02:08 2011 |
Manfred Valentan | Micron Baby | DUT4, source run, irrad, postzupf | cal119 | 83800 | 19.05.2011 09:57:57 | 19.05.2011 10:06:06 |
DUT4: B2Micron_2826_19_baby4 (combined p-stop)
config file: D:/cern10/micronbaby/data_lab/DUT4/postzupf/micronbaby_single_irrad_postzupf.cfg
HV=+-50V
90Sr 1mCi ~centered
I_start=95µA
I_end=137µA
Every second bond zupfed... |
| Attachment 1: cal119_goodstrips_apv4.png
|
 |
| Attachment 2: cal119_goodstrips_apv5.png
|
 |
|
146
|
Thu May 19 09:44:39 2011 |
Manfred Valentan | Micron Baby | DUT3, source run, irrad, postzupf | run118 | 100k | 19.05.2011 09:07:33 | 19.05.2011 09:27:21 |
DUT3: B2Micron_2826_7_baby2 (common p-stop)
config file: D:/cern10/micronbaby/data_lab/DUT3/postzupf/micronbaby_multi6_irrad_postzupf.cfg
HV=+-50V
90Sr 1mCi ~centered
I_start=18.0µA
I_end=22.6µA
Every second bond zupfed |
| Attachment 1: cal118_goodstrips_apv4.png
|
 |
| Attachment 2: cal118_goodstrips_apv5.png
|
 |
| Attachment 3: run118_all_hits_apv4.png
|
 |
| Attachment 4: run118_all_hits_apv5.png
|
 |
| Attachment 5: cal118_pednoise_apv4.png
|
 |
| Attachment 6: cal118_pednoise_apv5.png
|
 |
|
145
|
Thu May 19 09:42:28 2011 |
Manfred Valentan | Micron Baby | DUT3, source run, irrad, postzupf | cal118 | 83800 | 19.05.2011 08:56:18 | 19.05.2011 09:04:30 |
DUT3: B2Micron_2826_7_baby2 (common p-stop)
config file: D:/cern10/micronbaby/data_lab/DUT3/postzupf/micronbaby_single_irrad_postzupf.cfg
HV=+-50V
90Sr 1mCi ~centered
I_start=14.9µA
I_end=17.6µA
Every second bond zupfed |
| Attachment 1: cal118_goodstrips_apv4.png
|
 |
| Attachment 2: cal118_goodstrips_apv5.png
|
 |
|
144
|
Wed May 18 16:33:29 2011 |
Manfred Valentan | Micron Baby | B2Micron_2826_7_baby3, source run, unirrad, prezupf | run117 | 100k | 18.05.2011 15:59:39 | 18.05.2011 16:21:24 |
B2Micron_2826_7_baby3 (atoll p-stop)
config file: D:/cern10/micronbaby/data_lab/7baby3/postzupf/micronbaby_multi6_postzupf.cfg
HV=+-50V
90Sr 1mCi ~centered
I_start=1.3µA
I_end=1.7µA
Every second bond zupfed... |
| Attachment 1: cal117_goodstrips_apv04.png
|
 |
| Attachment 2: cal117_goodstrips_apv05.png
|
 |
| Attachment 3: run117_all_hits_apv4.png
|
 |
| Attachment 4: run117_all_hits_apv5.png
|
 |
| Attachment 5: cal117_pednoise_apv4.png
|
 |
| Attachment 6: cal117_pednoise_apv5.png
|
 |
|
143
|
Wed May 18 16:31:12 2011 |
Manfred Valentan | Micron Baby | B2Micron_2826_7_baby3, source run, unirrad, prezupf | cal117 | 83800 | 18.05.2011 15:44:58 | 18.05.2011 15:53:10 |
B2Micron_2826_7_baby3 (atoll p-stop)
config file: D:/cern10/micronbaby/data_lab/7baby3/postzupf/micronbaby_single_postzupf.cfg
HV=+-50V
90Sr 1mCi ~centered
I_start=1.0µA
I_end=1.3µA
Every second bond zupfed... |
| Attachment 1: cal117_goodstrips_apv04.png
|
 |
| Attachment 2: cal117_goodstrips_apv05.png
|
 |
|
142
|
Wed May 18 15:38:29 2011 |
Manfred Valentan | Micron Baby | TRK7, source run, unirrad, postzupf | run116 | 100k | 18.05.2011 15:02:05 | 18.05.2011 15:24:07 |
TRK7: B2Micron_2826_19_baby2 (common p-stop)
config file: D:/cern10/micronbaby/data_lab/TRK7/postzupf/micronbaby_multi6_postzupf.cfg
HV=+-50V
90Sr 1mCi ~centered
I_start=1.7µA
I_end=2.3µA
every second bond zupfed... |
| Attachment 1: cal116_goodstrips_apv4.png
|
 |
| Attachment 2: cal116_goodstrips_apv5.png
|
 |
| Attachment 3: run116_all_hits_apv4.png
|
 |
| Attachment 4: run116_all_hits_apv5.png
|
 |
| Attachment 5: cal116_pednoise_apv4.png
|
 |
| Attachment 6: cal116_pednoise_apv5.png
|
 |
|
141
|
Wed May 18 15:36:03 2011 |
Manfred Valentan | Micron Baby | TRK7, source run, unirrad, postzupf | cal116 | 83800 | 18.05.2011 14:43:18 | 18.05.2011 14:51:31 |
TRK7: B2Micron_2826_19_baby2 (common p-stop)
config file: D:/cern10/micronbaby/data_lab/TRK7/postzupf/micronbaby_single_postzupf.cfg
HV=+-50V
90Sr 1mCi ~centered
I_start=1.6µA
I_end=1.7µA
every second bond zupfed... |
| Attachment 1: cal116_goodstrips_apv4.png
|
 |
| Attachment 2: cal116_goodstrips_apv5.png
|
 |