 Wed Sep 29 10:30:59 2010, Markus Friedl, BELLE, run, run009, 30000, 29.09.2010 10:27:27, 29.09.2010 11:06:35
|
zero suppressed (HIT4) @ FADC
Belle stack: Origami-Micron-Micron-Origami - HIT4
HV=100V, Ibias=28A, beam on |
|
Wed Sep 29 09:39:33 2010, Markus Friedl, BELLE, cal, cal003, 83800, 29.09.2010 09:38:00,
|
| same as cal002, but now with corrected readout order |
|
Tue Sep 28 22:07:16 2010, Markus Friedl, BELLE, cal, cal002 DO NOT USE -> go to cal003, 83800, 28.09.2010 22:01:55,
|
Belle stack (Origami, Micron, Micron, Origami)
now cooling only for Origami, Micron are uncooled
chiller set point: -25°C, measured values on Origami: -10°C |
|
Tue Sep 28 15:09:16 2010, Markus Friedl, BELLE, run, run005, 40000, 28.09.2010 15:07:08, 28.09.2010 20:20:12
|
previous run stopped due to beam problem (shifted, broad, etc).
now recovered, restarting with same settings.
|
|
Tue Sep 28 14:48:00 2010, Markus Friedl, BELLE, run, run004, 1755, 28.09.2010 14:48:28, 28.09.2010 15:06:31
|
same as before, but now pos 1 is located on the other edge (-48mm from center)
telescope 7 / 30 / 277.5
telescope run 20079 |
|
Tue Sep 28 13:04:02 2010, Markus Friedl, BELLE, run, run003, 25000, 28.09.2010 13:00:05, 28.09.2010 14:41:14
|
now for real (previous run was at wrong position)
all same as run001, except position now still centered on p-strips, but on high edge (last APVs) for n side
position: 103 / 30 / 277.5 |
|
Tue Sep 28 12:54:33 2010, Markus Friedl, BELLE, run, run002, , 28.09.2010 12:46:54,
|
same as run001 after shifting x by 48mm
103 / 30 / 277.5 ? unsure after crash of xy stage PC |
|
Tue Sep 28 03:06:31 2010, Markus Friedl, BELLE, run, run001, 119516, 28.09.2010 03:06:04, 28.09.2010 12:18:33
|
first run with complete Belle stack: 2 x Origami, 2 x Micron
HV=100V I=49uA
beam is on |
|
Tue Sep 28 01:13:57 2010, Markus Friedl, BELLE, cal, cal001, 83800, 28.09.2010 01:11:20,
|
first intcal with complete Belle stack: 2 x Origami, 2 x Micron
HV=100V I=49uA
beam is on |
Tue Sep 28 23:29:50 2010, Markus Friedl, BELLE, run, run008, 140000, 28.09.2010 23:29:01, 29.09.2010 09:36:58 
|
Belle stack: Origami-Micron-Micron-Origami
HV=100V, Ibias=38A, beam on
cooling: Origami only, chiller: -25C, Module: -10C |
|
Tue Sep 28 23:24:35 2010, Markus Friedl, BELLE, run, run007, 1460, 28.09.2010 23:23:29, 28.09.2010 23:27:54
|
Belle stack: Origami-Micron-Micron-Origami
HV=100V, Ibias=38A, beam on
cooling: Origami only, chiller: -25C, Module: -10C |
|
Tue Sep 28 23:23:47 2010, Markus Friedl, BELLE, run, run006, 2003, 28.09.2010 23:13:22, 28.09.2010 23:22:26
|
| channels swapped -> stopped |
|
Thu May 19 11:04:04 2011, Manfred Valentan, Micron Baby, DUT4, source run, irrad, postzupf, run119, 100k, 19.05.2011 10:08:14, 19.05.2011 10:29:02 6x
|
DUT4: B2Micron_2826_19_baby4 (combined p-stop)
config file: D:/cern10/micronbaby/data_lab/DUT4/postzupf/micronbaby_multi6_irrad_postzupf.cfg
HV=+-50V |
|
Thu May 19 11:02:08 2011, Manfred Valentan, Micron Baby, DUT4, source run, irrad, postzupf, cal119, 83800, 19.05.2011 09:57:57, 19.05.2011 10:06:06
|
DUT4: B2Micron_2826_19_baby4 (combined p-stop)
config file: D:/cern10/micronbaby/data_lab/DUT4/postzupf/micronbaby_single_irrad_postzupf.cfg
HV=+-50V |
|
Thu May 19 09:44:39 2011, Manfred Valentan, Micron Baby, DUT3, source run, irrad, postzupf, run118, 100k, 19.05.2011 09:07:33, 19.05.2011 09:27:21 6x
|
DUT3: B2Micron_2826_7_baby2 (common p-stop)
config file: D:/cern10/micronbaby/data_lab/DUT3/postzupf/micronbaby_multi6_irrad_postzupf.cfg
HV=+-50V |
|
Thu May 19 09:42:28 2011, Manfred Valentan, Micron Baby, DUT3, source run, irrad, postzupf, cal118, 83800, 19.05.2011 08:56:18, 19.05.2011 09:04:30
|
DUT3: B2Micron_2826_7_baby2 (common p-stop)
config file: D:/cern10/micronbaby/data_lab/DUT3/postzupf/micronbaby_single_irrad_postzupf.cfg
HV=+-50V |
|
Wed May 18 16:33:29 2011, Manfred Valentan, Micron Baby, B2Micron_2826_7_baby3, source run, unirrad, prezupf, run117, 100k, 18.05.2011 15:59:39, 18.05.2011 16:21:24 6x
|
B2Micron_2826_7_baby3 (atoll p-stop)
config file: D:/cern10/micronbaby/data_lab/7baby3/postzupf/micronbaby_multi6_postzupf.cfg
HV=+-50V |
|
Wed May 18 16:31:12 2011, Manfred Valentan, Micron Baby, B2Micron_2826_7_baby3, source run, unirrad, prezupf, cal117, 83800, 18.05.2011 15:44:58, 18.05.2011 15:53:10
|
B2Micron_2826_7_baby3 (atoll p-stop)
config file: D:/cern10/micronbaby/data_lab/7baby3/postzupf/micronbaby_single_postzupf.cfg
HV=+-50V |
|
Wed May 18 15:38:29 2011, Manfred Valentan, Micron Baby, TRK7, source run, unirrad, postzupf, run116, 100k, 18.05.2011 15:02:05, 18.05.2011 15:24:07 6x
|
TRK7: B2Micron_2826_19_baby2 (common p-stop)
config file: D:/cern10/micronbaby/data_lab/TRK7/postzupf/micronbaby_multi6_postzupf.cfg
HV=+-50V |
|
Wed May 18 15:36:03 2011, Manfred Valentan, Micron Baby, TRK7, source run, unirrad, postzupf, cal116, 83800, 18.05.2011 14:43:18, 18.05.2011 14:51:31
|
TRK7: B2Micron_2826_19_baby2 (common p-stop)
config file: D:/cern10/micronbaby/data_lab/TRK7/postzupf/micronbaby_single_postzupf.cfg
HV=+-50V |
|