ELOG testbeam-SPS09

internal calibration 40 MHz transparent mode (cooling?)

cal007

22.08.2009 12:10:32

22.08.2009 12:49:09

Belle DUT, intcal
HV=80V, 40 MHz, beam off
1 sample, transparent mode
chiller set to 13 deg.

external 40 MHz clock

there was probably no water flow throught the pipe of the origami module during this run --> must be repeated

Sat Aug 22 11:54:49 2009

common

beam profile

beam shifted a bit in vertical direction downwards since 21. August 09 evening

Beam configuration:

Beam configuration file: H6b.802 (FM HAD (P0 off, H8=+180) PARLALLEL IN H6B SILC 2008

Attachment 1: 20090822_1150_beam_conditions.jpg

Sat Aug 22 11:26:00 2009

APVDAQ + telescope 40 MHz hit mode (cooling?)

HV=80V, 40 MHz, beam on, 120 GeV

6 samples, hit mode, hitcut=5

chiller set to 13 deg.

f=40 MHz

config file: cern09_belle_hit_cut5_multi6.cfg

trigger rate about 3500 ev / spill

there was probably no water flow throught the pipe of the origami module during this run!

Sat Aug 22 10:28:50 2009

APVDAQ + telescope 40 MHz hit mode (cooling?)

HV=80V, 40 MHz, beam on, 120 GeV

6 samples, hit mode, hitcut=4

chiller set to 13 deg.

f=40 MHz

config file: cern09_belle_hit_multi6.cfg

there was probably no water flow throught the pipe of the origami module during this run!

Sat Aug 22 09:44:50 2009

APVDAQ + telescope 31,8 MHz hit mode (cooling?)

HV=80V, 31.8 MHz, beam on, 120 GeV

6 samples, hit mode, hitcut=5

chiller set to 13 deg.

f=31.8 MHz

config file: cern09_belle_31.8mhz_hit_cut5_multi6.cfg

there was probably no water flow throught the pipe of the origami module during this run!

Sat Aug 22 08:32:02 2009

APVDAQ + telescope 31,8 MHz hit mode (cooling?)

HV=80V, 31.8 MHz, beam on, 120 GeV

6 samples, hit mode, hitcut=4

chiller set to 13 deg.

f=31.8 MHz

config file: cern09_belle_31.8mhz_hit_multi6.cfg

there was probably no water flow throught the pipe of the origami module during this run --> must be repeated

Sat Aug 22 03:27:13 2009

APVDAQ + telescope 31,8 MHz transparent mode (cooling?)

HV=80V, 31.8 MHz, beam on, 120 GeV

6 samples

chiller set to 13 deg.

f=31.8 MHz

config file: cern09_belle_31.8mhz_multi6.cfg

there was probably no water flow throught the pipe of the origami module during this run --> must be repeated

Sat Aug 22 01:06:34 2009

APVDAQ + telescope 40 MHz transparent mode (cooling?)

Belle DUT, tranparent mode
HV=80V, 40 MHz, beam on, 120 GeV
6 samples
chiller set to 13 deg.

beam position: p-side: APV2 of Origami, n-side: between APV1 and 2 of Origami (center of sensors), beam spot: 9x9 mm
JP-module is hit at APV3, module seems to be on a higher position than in past beam test (eventuelly flipped)

APVDAQ and telescope runs are not synchronized

trigger rate: about 300 - 500 ev / spill

there was probably no water flow throught the pipe of the origami module during this run --> must be repeated

Fri Aug 21 22:42:32 2009

EUDAQ config file used when running with telescope

common

Used until Friday, 21.08.09:

AndMask = 0xf # 4x4 mm scintillator for trigger

Used since Friday, 21.08.09:

AndMask = 0xc # 9x9 mm scintillator for trigger

Local trigger using TLU only: ALWAYS WITH 9x9mm scintillator

Attachment 1: testfortis_with_eudrb_beam_backpressure_WITH_SILC.conf

[RunControl]
RunSizeLimit = 1800000000
NoTrigWarnTime = 10

[DataCollector]

[LogCollector]
SaveLevel = EXTRA
PrintLevel = INFO

[Producer.TLU]
AndMask = 0xc # 9x9 mm scintillaotr for trigger
#AndMask = 0xf # 4x4 mm scintillator for trigger
OrMask = 0
VetoMask = 0
# EUDRB plugged into DUT#4 , FORTIS plugged into DUT#1, SiLC plugged into DUT#0 
#DutMask = 20 # EUDRB, FORTIS, SiLC in
DutMask = 17 # FORTIS, SiLC in
EnableDUTVeto = 2#0
TriggerInterval = 0
TrigRollover = 0
StrobePeriod = 16000000
StrobeWidth = 480000

[Producer.EUDRB]
Version = 2
Det = MIMOTEL
Mode = ZS
Unsynchronized = 1
AdcDelay = 3
ClkSelect = 2
#Marker1 = 0xff
#Marker2 = 0xff
PostDetResetDelay = 4
PedestalFile = auto
IDOffset = 0
NumBoards = 6
Board0.Slot = 3
Board1.Slot = 5
Board2.Slot = 7
Board3.Slot = 9
Board4.Slot = 11
Board5.Slot = 13

[Producer.FORTIS]
# Need \ not / for directory name with Cygwin...
# ExecutableDirectory = /home/cussans/optodaq/halsall_test_v5/
ExecutableDirectory = /home/cussans/optodaq/MyF11/
# ExecutableDirectory = /home/cussans/optodaq/MyF10/
ExecutableProcessName = optodaqV.exe
#ExecutableFilename = test_run_128_block_mod_C2.bat
ExecutableFilename = test_run_512_128_block_mod_CX.bat
# ExecutableFilename = test_run_512_448_block_mod_full.bat
ExecutableArgs = 
NumRows = 512
NumColumns = 128

Fri Aug 21 18:35:13 2009

APVDAQ + telescope 31.8 MHz transparent mode

4 Belle DUTs
HV=80V, 31.8 MHz, 6 sample, 120 GeV
external clock source
transparent mode
beam position: p-side: APV2 of Origami, n-side: between APV1 and 2 of Origami (center of sensors), beam spot: 9x9 mm

JP-module is hit at APV3, module seems to be on a higher position than in past beam test (eventuelly flipped)

APVDAQ and telescope runs are not synchronized

Fri Aug 21 18:07:57 2009

APVDAQ standalone 31.8 MHz

pedcorr004

21.08.2009 17:49:10

21.08.2009 18:24:31

4 Belle DUTs
HV=80V, 31.8 MHz
pedestal correction
transparent mode
beam on

Fri Aug 21 17:14:58 2009

Wolfgang Kiesenhofer

S/N Histograms Raw (no data selection)

run001 (strips), run002 (pitch adapter), run003 (upper edge)

Attachment 1: sn_langaufit_raw_strips.pdf

Attachment 2: sn_langaufit_raw_pa.pdf

Attachment 3: sn_langaufit_raw_edgerun.pdf

Fri Aug 21 16:37:22 2009

internal calibration 40 MHz hit mode

cal006

21.08.2009 16:30:33

Belle DUT, intcal
HV=80V, 40 MHz, no beam
hit mode

switched back to internal 40 MHz clock

Fri Aug 21 15:27:08 2009

internal calibration 31.8 MHz hit mode

cal005

21.08.2009 15:34:43

21.08.2009 16:29:47

Belle DUT, intcal
HV=80V, 31.8 MHz, no beam
hit mode

Origami p-side APV 2&3 with reverse readout order

Fri Aug 21 14:18:11 2009

internal calibration 31.8 MHz transparent mode

cal004

21.08.2009 14:21:40

21.08.2009 15:01:24

Belle DUT, intcal
HV=80V, 31.8 MHz, no beam
transparent mode

Origami p-side APV 2&3 with reverse readout order

Fri Aug 21 13:38:20 2009

APVDAQ standalone 31.8 MHz hit mode

run011

75000

21.08.2009 13:35:25

4 Belle DUTs
HV=80V, 31.8 MHz, 6 sample, 120 GeV
external clock source
processed mode, hit cut = 5
beam position: p-side: APV2 of Origami, n-side: between APV1 and 2 of Origami (center of sensors)

JP-module is hit at APV3, module seems to be on a higher position than in past beam test (eventuelly flipped)

Fri Aug 21 12:22:43 2009

APVDAQ standalone 31.8 MHz hit mode

4 Belle DUTs
HV=80V, 31.8 MHz, 6 sample, 120 GeV
switched to external clock source
processed mode, hit cut = 4
beam position: p-side: APV2 of Origami, n-side: between APV1 and 2 of Origami (center of sensors)

JP-module is hit at APV3, module seems to be on a higher position than in past beam test (eventuelly flipped)

Fri Aug 21 12:08:44 2009