| ID |
Date |
Author |
Project |
Measurement Type |
Object ID |
Subject |
Text |
 |
|
46
|
Fri May 22 12:01:32 2015 |
Hao Yin | | | | CMC injection LV 10V | Comparison w/o filter (LC) connected to
-z_n side.
Mateo has the results. |
|
|
45
|
Thu May 21 18:23:22 2015 |
Hao Yin | | | | Noise Injection LV cable | (TestNr. 15)
injecting sin wave into LV at different |
|
|
44
|
Wed May 20 10:12:12 2015 |
Hao Yin | | | | Ladder RLC test (CMC Injection) | L5 Ladder Test
folder: /mnt/data/ITA_NOISE_TESTS/Ladder_test
Setup: ladder |
|
|
43
|
Tue May 19 14:48:06 2015 |
Hao Yin | Belle II | module | L6 Noise inJection Runs | L6 Noise inJection Runs | Folder "L6_RLC_Test"
Configuration file: /mnt/data/ITA_NOISE_TESTS/L6_RLC_Test/SinglePeak_3Fadc.cfg
3 Tests: Injkection to 2.5V 1.25V. |
|
|
42
|
Tue May 19 13:42:04 2015 |
Hao Yin | | | | L6 Noise inJection Setup | Test Nr. 1:
RLC between DockBox and Hybrid
(both side). |
|
|
41
|
Tue May 19 13:23:16 2015 |
Hao Yin | Belle II | system | Calibration | CalibrationRun001 | PedestalRun001, FIRRun001,
room temperature,
no noise injection |
|
|
40
|
Tue May 19 11:01:29 2015 |
Hao Yin | Belle II | system | Pedestal | PedestalRun | FIRRun001
Baseline measurement without injections,
50000 event, |
16x |
|
39
|
Tue May 19 10:57:19 2015 |
Hao Yin | Belle II | system | FIR | FIR filter | first fir filter run:
# 1:[0x[FADC ID] in hex], 2:[APV25
ChannelNr], 3-10:[fir coef in float] |
|
|
38
|
Tue May 19 10:08:53 2015 |
Hao Yin | | | | FADC system setup success | 3 FADC. All Channel/APV25 running (except
L3 n first and last -> not connected (bonding))
n-side: all connectors |
|
|
37
|
Tue May 19 09:31:50 2015 |
Hao Yin | | | | Noise Test ITA | Everything works except L3 p-side.
The config file is shown in the
following: |
|
|
36
|
Thu Jun 5 10:34:45 2014 |
Benedikt Würkner | Belle II | source | Silc Module | Silc Angle Measurement 10° | Measured the Silc 03/10 Module using the
Sr90 Source to have a comparison for the
Eta-Distribution at different angles. |
|
|
35
|
Thu Jun 5 10:34:29 2014 |
Benedikt Würkner | Belle II | source | Silc Module | Silc Angle Measurement 7° | Measured the Silc 03/10 Module using the
Sr90 Source to have a comparison for the
Eta-Distribution at different angles. |
|
|
34
|
Thu Jun 5 10:34:06 2014 |
Benedikt Würkner | Belle II | source | Silc Module | Silc Angle Measurement 4° | Measured the Silc 03/10 Module using the
Sr90 Source to have a comparison for the
Eta-Distribution at different angles. |
|
|
33
|
Thu Jun 5 10:33:46 2014 |
Benedikt Würkner | Belle II | source | Silc Module | Silc Angle Measurement 1° | Measured the Silc 03/10 Module using the
Sr90 Source to have a comparison for the
Eta-Distribution at different angles. |
|
|
32
|
Fri May 16 11:40:29 2014 |
Benedikt Würkner | Belle II | source | L3 module | No 6 of 6 room temperature measurements using Sr90 Source (single) | Sr90 Radioactive Source
No cooling
Module position: -54:-10(bottom right) |
10x |
|
31
|
Fri May 16 11:38:44 2014 |
Benedikt Würkner | Belle II | source | L3 module | No 5 of 6 room temperature measurements using Sr90 Source (single) | Sr90 Radioactive Source
No cooling
Module position: -27:-10(bottom center) |
10x |
|
30
|
Fri May 16 11:37:05 2014 |
Benedikt Würkner | Belle II | source | L3 module | No 4 of 6 room temperature measurements using Sr90 Source (single) | Sr90 Radioactive Source
No cooling
Module position: 0:-10(bottom left) |
10x |
|
29
|
Fri May 9 16:44:41 2014 |
Benedikt Würkner | Belle II | source | L3 module | No 3 of 6 room temperature measurements using Sr90 Source (single) | Sr90 Radioactive Source
No cooling
Module position: -54:0(top center) |
10x |
|
28
|
Fri May 9 15:12:44 2014 |
Benedikt Würkner | Belle II | source | L3 module | No 2 of 6 room temperature measurements using Sr90 Source (single) | Sr90 Radioactive Source
No cooling
Module position: -27:0(top center) |
10x |
|
27
|
Thu May 8 16:51:57 2014 |
Benedikt Würkner | Belle II | source | L3 module | No 2 of 6 room temperature measurements using Sr90 Source (single) | Failed with Error: "***ERROR*** Init
NECO failed, Return code: -32761"
Restarted and it works again |
|