 Sat Jun 13 13:01:39 2015, Hao Yin, Belle II FADC (H6A), Hardware, 029, , 3, No, Good
|
room temp
FIRRun002,
PedestalRun012, |
|
Sat Jun 13 16:47:28 2015, Benedikt Würkner, SVD3 (H6B), Mimosa threshold with FEI4, 82, 12000, , No, Good
|
Set mimosa threshold to 5 and recorded with FEI4 upstream
L3 already in sensor but not yet configured.
Probably to noisy to help much |
Sat Jun 13 17:05:35 2015, Benedikt Würkner, SVD3 (H6B), L3 with FEI4, 84, 30000, 1, No, Good 
|
| L3 sensor at position x: 105, y: 47 hitting apvs: 2&3 on p-side and apv 3 on n-side |
|
Sat Jun 13 18:02:04 2015, Benedikt Würkner, SVD3 (H6B), L3 with FEI4, 85, 70000, 2, No, Good
|
| L3 sensor at position x: 115, y: 47 hitting apvs: 2&3 on p-side and apv 3&4 on n-side |
|
Sat Jun 13 19:14:41 2015, Benedikt Würkner, SVD3 (H6B), L3 with FEI4, 86, 732000, 3, No, Good
|
| L3 sensor at position x: 115, y: 57 hitting apvs: 1&2 on p-side and apv 3&4 on n-side |
|
Sat Jun 13 19:26:26 2015, Hao Yin, Belle II FADC (H6A), Hardware, 030, , 3, No, Good
|
room temp
FIRRun002,
PedestalRun012, |
|
Sat Jun 13 19:29:50 2015, Hao Yin, Belle II FADC (H6A), Hardware, 030, , 1, No, Good
|
room temp
FIRRun002,
PedestalRun012, |
|
Tue May 12 10:27:39 2015, Benedikt Würkner, SVD3 (H6B), Setup information, , , , , Unknown
|
Information concerning the SVD3 setup during a beam test
In the beam area setup the whole crate and the power supply with the usual spider cable and the two Keithly 2410 high voltage supplies.
Monitoring of the 2410 happens via a NI MAX interface that connects to the GPIB-Ethernet interface and needs to be configured there. The IP and password |
|
Wed Jun 3 10:48:42 2015, Benedikt Würkner, common, Networking, , , , , Unknown
|
WLAN Router:
SSID: Hephy
password: 20supersecret14
DHCP Range: 192.168.0.200 to 239 |
|
Wed Jun 3 17:23:07 2015, Thomas Bergauer, Belle II FADC (H6A), XY stage positions, , , , , Unknown
|
x-Achse: positiv Richtung Saleve (counting room)
y-Achse: positiv Richtung UNTEN!! |
|
Thu Jun 4 14:15:50 2015, Hao Yin, Belle II FADC (H6A), FIR, 001, , , , Good
|
FIR filer and ADC delay with all sensor and telescope.
telescope n-side switched. |
|
Thu Jun 4 14:16:20 2015, Hao Yin, Belle II FADC (H6A), Pedestal, 001, 10000, , , Good
|
FirRun001, room temp
telescope n-side switched. |
|
Thu Jun 4 18:45:42 2015, Hao Yin, Belle II FADC (H6A), Pedestal, 003, 10000, , , Good
|
firrun003, room temp
|
|
Thu Jun 4 18:49:03 2015, Benedikt Würkner, SVD3 (H6B), Setup, , , , , Unknown
|
| |
|
Fri Jun 5 12:02:29 2015, Hao Yin, Belle II FADC (H6A), Sixlet Calibration, 001, , , , Good
|
| room temp max subevent at 2. with lat = 96 |
|
Fri Jun 5 12:03:34 2015, Hao Yin, Belle II FADC (H6A), Sixlet Calibration, 002, , , , Good
|
| lat = 97 to a greater range of lat scan |
|
Fri Jun 5 19:55:00 2015, Hao Yin, Belle II FADC (H6A), Sixlet Calibration, 003, , , , Unknown
|
lat = 98
room temp
pedestalrun 003 |
|
Fri Jun 5 19:59:44 2015, Hao Yin, Belle II FADC (H6A), Pedestal, 004, 10000, , , Good
|
update pedestal values for room temp sixlet runs.
|
|
Fri Jun 5 23:38:51 2015, Hao Yin, Belle II FADC (H6A), Pedestal, 005, 10000, , , Unknown
|
Readjust after cooling box.
room temp, firrun002
|
|
Sat Jun 6 16:14:36 2015, Benedikt Würkner, SVD3 (H6B), calibration run and setup information, cal01, , , , Unknown
|
Calibration Run with +- 50V Bias with higher compliance since the p-side draws more current than expected (23muA by the MAMBO)
|
|