Home CMS Production Clean room MedAustron HEPHY testbeams old
testbeam-DESY-Oct2017 testbeam-DESY-April2017 testbeam-SPS2015 testbeam-SPS2014 testbeam-DESY14 testbeam-SPS12 testbeam-SPS11 testbeam-SPS10 testbeam-SPS09 testbeam-SPS08 LP-TPC
  Belle testbeam at SPS in June 2015, Page 1 of 6  Not logged in ELOG logo
New entries since:Thu Jan 1 01:00:00 1970
ID Dateup Author Project Subject Run Number Events XYPosition Cooling Data
  1   Tue May 12 10:27:39 2015 Benedikt WürknerSVD3 (H6B)Setup information    Unknown

Information concerning the SVD3 setup during a beam test

In the beam area setup the whole crate and the power supply with the usual spider cable and the two Keithly 2410 high voltage supplies. Monitoring of the 2410 happens via a NI MAX interface that connects to the GPIB-Ethernet interface and needs to be configured there. The IP and password are noted on the device. The software can be found on heros in medialib/LONGTERM/longterm R3.1_doubleSided as a normal *.vi file. 

Default adresses 16 and 17 as defined in labview, need to figure out on site which is which, if the voltage selected (e.g. 100V) is applied as +50/-50 or if it is applied as +100/-100 before connecting the cables. 

Take a run without dut as well to check the telescope integrity. Without dut in beamline!!!!!

  2   Wed Jun 3 10:48:42 2015 Benedikt WürknercommonNetworking    Unknown

WLAN Router:

SSID: Hephy

password: 20supersecret14

DHCP Range: to 239

Netmask: /24

DNS Server:


external IP: (für diverse Port Forwardings)


Manuell vergebene IP Adressen bitte unbedingt Benni mitteilen oder/und in der folgenden Tabelle eintragen! 

IP/MAC Zuweisung:

IP Machine/Name intern Port Forwarding (aussen) SVD Kenwood  VNC(5900)  VNC(9000) SVD3 DAQ  VNC(5900)  VNC(9001) TUX DAQ  VNC(5900), VNC(5901), SSH(22)  VNC(9009), VNC(9002), SSH(9003), Belle XY Tisch TUXOA  SSH(22), VNC(5900)  SSH(9004), VNC(9012) JTAG Server alixcool slowcontrol  VNC(5900)  VNC(9005) CAEN Power supply zenpixelwiki  SSH(22), VNC(5900)  SSH(9006), VNC(9008) TLU (pcx25042, XY)  VNC(5900)  VNC(9007) Cooling control PC VNC(5900) VNC(9011) NI GPIB - ENET / 1000 Printserver  VNC(5900)  VNC(9010) Aida PC   vnc(5900)


Admin Zugang Wlan Router:


Username: admin

password: Hephy2014


  3   Wed Jun 3 17:23:07 2015 Thomas BergauerBelle II FADC (H6A)XY stage positions    Unknown

x-Achse: positiv Richtung Saleve (counting room)

y-Achse: positiv Richtung UNTEN!!


position of laddertestbox xy stages:

Rev. Pos (BWD Sensor, BWD, Oben) x= 82.3, y=110.6

Mitte Sensor:

Pos 1: (mitte BWD sensor): x=144.74, y=80.8

Pos 2: (mitte Origami -z): x=269.62, y=80.8

Pos 3: (mitte Origami ce): x=394.42, y=80.8

Pos 4 (mitte FWD Micron Sensor): x=517, y=80.8


Pos 5 (Ecke BWD sensor): x=92.3, y=105.6

Pos 6 (Ecke Origami -z): x=217.18, y=105.6

Pos 7 (Ecke Origami ce): x=342.06, y=105.6

Pos 8 (Ecke FWD sensor): x=467,62, y=56,3 

Pos 9 (Ecke FWD sensor): x=568,33 y=64,48

  4   Thu Jun 4 14:15:50 2015 Hao YinBelle II FADC (H6A)FIR001   Good

FIR filer and ADC delay with all sensor and telescope.
telescope n-side switched.

  5   Thu Jun 4 14:16:20 2015 Hao YinBelle II FADC (H6A)Pedestal00110000  Good

FirRun001, room temp
telescope n-side switched.

  6   Thu Jun 4 15:12:41 2015 Hao YinBelle II FADC (H6A)Hardware001500001NoGood

PedestalRun001, FIRRun001, room temp
telescope n-side switched.
In order to correct the position change the

  7   Thu Jun 4 18:44:50 2015 Hao YinBelle II FADC (H6A)Hardware002500002NoGood

room temp, FIRRun001, pedestal run 003

  8   Thu Jun 4 18:45:42 2015 Hao YinBelle II FADC (H6A)Pedestal00310000  Good

firrun003, room temp

  9   Thu Jun 4 18:49:03 2015 Benedikt WürknerSVD3 (H6B)Setup    Unknown
  10   Thu Jun 4 22:07:16 2015 Hao YinBelle II FADC (H6A)Hardware003189k3NoGood

CE. pedestal run 003. Fir run 002. Room temp

  11   Fri Jun 5 08:20:27 2015 Hao YinBelle II FADC (H6A)Hardware004500004NoGood

room temp, FIRRun002, pedestalrun003, taget FW

  12   Fri Jun 5 12:02:29 2015 Hao YinBelle II FADC (H6A)Sixlet Calibration001   Good

room temp max subevent at 2. with lat = 96

  13   Fri Jun 5 12:03:34 2015 Hao YinBelle II FADC (H6A)Sixlet Calibration002   Good

lat = 97 to a greater range of lat scan

  14   Fri Jun 5 19:55:00 2015 Hao YinBelle II FADC (H6A)Sixlet Calibration003   Unknown

lat = 98

room temp

pedestalrun 003

  15   Fri Jun 5 19:59:44 2015 Hao YinBelle II FADC (H6A)Pedestal00410000  Good

update pedestal values for room temp sixlet runs.

  16   Fri Jun 5 23:38:51 2015 Hao YinBelle II FADC (H6A)Pedestal00510000  Unknown

Readjust after cooling box.

room temp, firrun002

  17   Fri Jun 5 23:39:49 2015 Hao YinBelle II FADC (H6A)Hardware005~200k5NoGood

FIRRun002, pedestalrun005, room temp
Target BW: beam spot at ~ (0 p, 0 n)

  18   Sat Jun 6 12:43:55 2015 Hao YinBelle II FADC (H6A)Hardware006500006NoGood

FIRRun002, room temp, pedestalrun005,
layout: same as HW 005
target: -z, pos 6 (strip: p-0, n-0);

NOTE: results shown in the attachments has been evaluated with cmc containing 128 strip

  19   Sat Jun 6 14:28:28 2015 Hao YinBelle II FADC (H6A)Harware007500007NoGood

room temp, FIRRun002, PedestalRun005, room temp

target: CE, pos 7 (p-0, n-0)

  20   Sat Jun 6 16:14:36 2015 Benedikt WürknerSVD3 (H6B)calibration run and setup informationcal01   Unknown

Calibration Run with +- 50V Bias with higher compliance since the p-side draws more current than expected (23muA by the MAMBO)


ELOG V3.1.4-395e101