Der zweite PM (entsprechend der Beamrichtung) war von Anfang an nicht angeschlossen an die TLU! Stattdessen war ein Atlas pixel sensor, welcher als 4ter PM fungiert angeschlossen. Genau dieser "PM" hatte 0 counts bei der TLU --> Igor sagt, dass dieser Sensor ("PM") anscheinend keine Versorgungsspannung hatte (~400V). Jetzt baut Igor diesen Atlas Sensor wieder aus und hat bereits den nicht angeschlossenen PM wieder angeschlossen an die TLU. DIeser PM zeigt aber nun zu viele counts. Deshalb behalten wir die AND mask 11 (auch jetzt bei den Belle Modulen).

correct mapping

cooled -25 °C

L3n deactivated

Pedestal Run

room temperature (30C)

Bias scans planned

Initial pedestal run with SVD3 setup and WedgeOld, FW993, BW993 (reading out 4 chips on every p-side)

At room temperature.

Pedestal run at room temperature.

6 subevents. Noise reference run.

Delay as latest run.

Reference run for bad strips.

New pedestal run after switching the connectors.

At room temperature 

At room temperature.

Old delay settings and FIRRun_002

Temperature: See attachment

FIRFilterRun_002

Layer 3-n side deactivated, because Hao broke it.

temp see attachment (von flo)
10000
latest fir filter (002)

cooled (temperature see attachment latest noise run),

latest Noise, FIR settings with the right layout mapping.

cooled see appendix (FIRRun003)

MaxEvents 10000

cooled see appendix (FIRRun003)

MaxEvents 10000

We moved the second cable to the third connector on the FADC to match DESY testbeam conditions. 

Windows PC at Telescope:

0.) JTAG Programming: Chose a threshold file (recommended threshold 5) File: M26TB_Cern_2011.thresh5.mcf--> press start

1.) C:\Users\telescope\Desktop\users\BelleII --> start Mimosa 26 Telescope --> select all six Mimosa's

2.) C:\Users\telescope\Desktop\users\BelleII --> start startEudaq_fullWindows.bat

3.) Use configuration file hephy1 (location: C:\eudaq\conf). Change it according to your TLU settings (DUT mask, AND mask, etc.)

4.) configure

5.) start

x) Online monitor in preparation

Files: Are saved in C:\eudaq\data with internal numbering "run000000xxx.raw" (look at the date and time). [You can connect locally to this folder at HEPHY-SVD PC]

Logbook: https://ab-dep-op-elogbook.web.cern.ch/ab-dep-op-elogbook/elogbook/secure/eLogbook.php?shiftId=1059325

Monitor:  http://op-webtools.web.cern.ch/op-webtools/vistar/vistars.php?usr=SPS1

* CCC (zentraler Beschleuniger-Kontrollraum): 77500

* H6A Controlroom: 76755

* HEPHY-Handy: 16-2471 or +41 76 487 2471 from outside of CERN

* Office in Meyrin: 12-R11: 74592

Hostel-Zimmern:

* Bergi: 79326

* Benni: 60232

* Hao: 70408

Andere Wichtige Leute:

* Beam-Dame: Edda Gschwendner 16-5080

* NA Hallen Verantwortlicher: Michael Jeckel

Lookup Telefonnummern: http://phonebook.cern.ch

At room temperature

First run was at: 23 (no track)

TimingRun_001:

Trigger delay: 26

 

TimingRun_002:

Trigger delay: 29

TimingRun_003:

Trigger delay: 32


 

TimingRun_004:

Trigger delay: 20

TimingRun_005:

Trigger delay: 17

 

TimingRun_005:

Trigger delay: 14
Trigger chip delay: 110

Infineon_run002 is just a calibration run for the vertical positioned sensors.