 Tue Nov 18 09:48:53 2014, Hao Yin, Belle SVD, PedestalRun_004, , 10000, Tue Nov 18 09:48:30 CET 2014, , Unknown
|
At room temperature.
Old delay settings and FIRRun_002
|
|
Tue Nov 18 10:12:25 2014, Hao Yin, Belle SVD, 6let PedestalRun_005, , 10000, Tue Nov 18 10:11:45 CET 2014, , Unknown
|
At room temperature
Latest delay, FIRRun002.
Check for bad strips. |
|
Tue Nov 18 10:26:56 2014, Hao Yin, Belle SVD, CalibrationRun_003, , , Tue Nov 18 10:26:52 CET 2014, , Unknown
|
At room temperature
Latest delay and FIRRun |
|
Tue Nov 18 18:45:01 2014, Hao Yin, Belle SVD, Trigger Delay scan, , , Tue Nov 18 18:21:50 CET 2014, , Unknown
|
At room temperature
First run was at: 23 (no track)
TimingRun_001:
Trigger delay: 26
TimingRun_002:
Trigger delay: 29
TimingRun_003:
Trigger delay: 32
TimingRun_004:
Trigger delay: 20
TimingRun_005:
Trigger delay: 17
TimingRun_005:
Trigger delay: 14
Trigger chip delay: 110
|
|
Tue Nov 18 20:26:12 2014, Hao Yin, Belle SVD, HardwareRun_001, , , Tue Nov 18 18:21:50 CET 2014, , Unknown
|
At room temperature
Latest ADC scan and FIR run.
Latest CAL.
Position: 0.0, see elog entry. |
|
Tue Nov 18 20:42:18 2014, Benedikt Würkner, Belle SVD, Coordinates of the DUT, , , , , Unknown
|
We set the coordinates trying to put the beam in an area with well working APVs
Peak of course differs for n and p sensors due to their different pitch.
L4-6 n-side Peak around strip 180
L4&6 p-side mean value around strip 380
L5 p-side moved by 4.8mm due to reasons (APV misalignment I think) therefore the peak of the same measurements is moved by 4.8/75µm = 64 strips therefore centered around strip 320
The coordinates of the x-y table were set to 0:0 at this point. Refer to Run Alignment2 for reference data. |
Wed Nov 19 20:04:53 2014, Hao Yin, Belle SVD, PedestalRun_006, , , , , Unknown 
|
Temperature: See attachment
FIRFilterRun_002
Layer 3-n side deactivated, because Hao broke it. |
|
Wed Nov 19 20:07:05 2014, Hao Yin, Belle SVD, HardwareRun_002, , , , , Unknown
|
Multi-6 cooled.
See latest Noise, and PedestalRun.
|
|
Wed Nov 19 22:25:29 2014, Hao Yin, Belle SVD, PedestalRun_008 [CheckLayout], , , , , Unknown
|
cooled (temperature see attachment latest noise run),
latest Noise, FIR settings with the right layout mapping. |
|
Wed Nov 19 22:59:24 2014, Hao Yin, Belle SVD, CalibrationRun_004, , , , , Crap
|
cooled (see last calibration run)
Latest noise, FIRfilter settings.
Failed due to VME read timeout. |
|
Wed Nov 19 23:15:50 2014, Hao Yin, Belle SVD, HardwareRun_003, , , , , Unknown
|
cooled, latest noise, cal, PedestalRun.
Rawmode |
|
Wed Nov 19 23:31:08 2014, Hao Yin, Belle SVD, HardwareRun_004, , , , , Unknown
|
Same as HardwareRun_003 but with ZS. |
|
Thu Nov 20 00:52:50 2014, Hao Yin, Belle SVD, FIRRun_002, , , , , Unknown
|
cooled with new delay run |
|
Thu Nov 20 00:54:21 2014, Hao Yin, Belle SVD, PedestalRun_008, , , , , Unknown
|
temp see attachment (von flo)
10000
latest fir filter (002) |
|
Thu Nov 20 00:55:14 2014, Hao Yin, Belle SVD, HardwareRun_007, , , , , Unknown
|
temp cooled see attachment
last noise run(007)
FIRRun_002
PedestalRun_008
new cal run Raw, test with put fifo full flags |
|
Thu Nov 20 10:22:17 2014, Markus Friedl, Belle SVD, common, , , , , Unknown
|
- Some VME errors occured over night
- Optical fiber changed
- Situation improved
- L3n hybrid could not be configured by I2C
- Plugged cable into the former FWDn slot
- Fully working
|
|
Thu Nov 20 10:33:13 2014, Benedikt Würkner, Belle SVD, FIRRun and Delay Scan, 003, , , , Unknown
|
Cooled see appendix
with new layout (l3_n-side channels changed and reactivated).
Latest FIRRun |
|
Thu Nov 20 10:39:11 2014, Benedikt Würkner, Belle SVD, PedestalRun_009, , , , , Unknown
|
cooled see appendix (FIRRun003)
MaxEvents 10000
|
|
Thu Nov 20 10:39:13 2014, Benedikt Würkner, Belle SVD, PedestalRun_009, , , , , Unknown
|
cooled see appendix (FIRRun003)
MaxEvents 10000
|
|
Thu Nov 20 10:41:54 2014, Benedikt Würkner, Belle SVD, CalibrationRun_005, , , , , Unknown
|
cooled see appendix (FIRRun_003)
PedestalRun_009 |
|