 Sun Nov 23 15:13:37 2014, Markus Friedl, Belle SVD, HardwareRun, 003, 100600, 23.11.2014 14:07:23, 23.11.2014 16:51:27, Good
|
Hardware run, hitting APVs 0/1 on p-sides, 1/2 on n-sides
EUDAT telescope running with difference of 2 events |
Sun Nov 23 17:51:44 2014, Benedikt Würkner, Belle SVD, HardwareRun, 046, 100000, 20:06, 20:36, Unknown
|
Hardware Run +-60V Bias
Room Temperature
Pedestal 018 (again marked all the bad strips)
Zero Suppressed
|
|
Sun Nov 23 01:37:42 2014, Hao Yin, Belle SVD, HardwareRun, 040, 20000, 2014-11-23 01:37:00, , Unknown
|
Bias voltage set to +-80V
Pedestal_015 (cooled)
"New" layout with no cooling (CO2 is no more)
Newly set values for APC Delay
New FIR Run 005
Temperature around 30 C
Bias: +-80V |
Sat Nov 22 11:37:16 2014, Benedikt Würkner, Belle SVD, HardwareRun, 036, 450378, 2014-11-22 1:00:00, 2014-11-22 10:27:54, Unknown 
|
Not completely cooled since cooling failed at 1:42 in the night
Bias voltage set to +-60V
Some error with event no17 or 18 leading to the data not being easily analysable requiring a hack in TuxOA
Pedestal_013 (cooled)
Noisefile: HardwareRun_036.noi |
|
Sat Nov 22 15:31:49 2014, Hao Yin, Belle SVD, HardwareRun, 038, 43788, 2014-11-22 15:18:40, , Unknown
|
Cooled down to -20
Bias voltage set to +-60V
Pedestal_013 (cooled)
Noisefile: HardwareRun_036.noi
Zero suppressed |
|
Sun Nov 23 01:05:43 2014, Hao Yin, Belle SVD, HardwareRun, 039, 20000, 2014-11-22 15:18:40, , Crap
|
Cooled down to -20
Bias voltage set to +-80V
Pedestal_013 (cooled)
Noisefile: HardwareRun_036.noi
|
|
Fri Nov 21 15:07:24 2014, Benedikt Würkner, Belle SVD, HardwareRun, 019, 150948, 2014-11-21 02:41:55, 2014-11-21 10:11:02, Unknown
|
cooled see appendix (FirRun003)
PedestalRun_010
multi 6 Raw Mode
FIFO size increased
L3n deactivated
100000 deadtime (CTRL TRG)
VME Error, overnight run |
|
Fri Nov 14 19:01:27 2014, Thomas Bergauer, common, Administrative Procedures for Departure, , , , , Unknown
|
Wednesday:
* Transport request starten (I do not need any transport service) von 887 nach Wien. Das triggert automatisch die Radio Protection Leute. Der EDH Request hängt dann bei irgend einem Franzosen. Den bitte anrufen und für Montag mittags einen Termin ausmachen. Es muss alles geschnüffelt werden, was in der Zone war (also nicht im Counting room)
Merchandise-Bestätigung für die Anreise ist im attachment!
Anreise: https://edh.cern.ch/Document/SupplyChain/SHIP/5855845
Abreise: https://edh.cern.ch/Document/SupplyChain/SHIP/5863835
|
|
Fri Nov 14 19:22:40 2014, Martin Kurz, common, ip addresses, portforwarding, wlan, , , , , Unknown
|
WLAN Router:
SSID: Hephy
password: 20supersecret14
DHCP Range: 192.168.0.200 to 239
Netmask: /24
DNS Server: 192.168.0.254
Gateway: 192.168.0.254
external IP: 128.141.61.16 (für diverse Port Forwardings)
Manuell vergebene IP Adressen bitte unbedingt Martin Kurz mitteilen oder/und in der folgenden Tabelle eintragen!
IP/MAC Zuweisung:
| IP |
Machine/Name |
intern |
Port Forwarding (aussen) |
| 192.168.0.10 |
SVD Kenwood |
VNC(5900) |
VNC(9000) |
| 192.168.0.11 |
AIDA DAQ |
VNC(5900) |
VNC(9001) |
| 192.168.0.12 |
TUX DAQ |
VNC(5900), VNC(5901), SSH(22) |
VNC(9009), VNC(9002), SSH(9003), |
| 192.168.0.13 |
Belle XY Tisch |
|
|
| 192.168.0.14 |
TUXOA |
SSH(22) |
SSH(9004) |
| 192.168.0.15 |
JTAG Server |
|
|
| 192.168.0.148 |
alixcool |
|
|
| 192.168.0.16 |
slowcontrol |
VNC(5900) |
VNC(9005) |
| 192.168.0.144 |
CAEN Power supply |
|
|
| 192.168.0.17 |
zenpixelwiki |
SSH(22), VNC(5900) |
SSH(9006), VNC(9008) |
| 192.168.0.18 |
TLU (pcx25042, XY) |
VNC(5900) |
VNC(9007) |
| 192.168.0.240 |
NI GPIB - ENET / 1000 |
|
|
| 192.168.0.150 |
Printserver |
VNC(5900) |
VNC(9010) |
| |
|
|
|
| |
|
|
|
Admin Zugang Wlan Router:
IP: 192.168.0.254
Username: admin
password: Hephy2014
|
|
Fri Nov 14 19:47:25 2014, Thomas Bergauer, , Telefonnummern, , , , , Unknown
|
* CCC (zentraler Beschleuniger-Kontrollraum): 77500
* H6A Controlroom: 76755
* HEPHY-Handy: 16-2471 or +41 76 487 2471 from outside of CERN
* Office in Meyrin: 12-R11: 74592
Hostel-Zimmern:
* Bergi: 79326
* Benni: 60232
* Hao: 70408
Andere Wichtige Leute:
* Beam-Dame: Edda Gschwendner 16-5080
* NA Hallen Verantwortlicher: Michael Jeckel
Lookup Telefonnummern: http://phonebook.cern.ch
|
|
Fri Nov 14 19:49:04 2014, Florian Buchsteiner, common, Belle Setup, , , , , Unknown
|
| |
|
Fri Nov 14 19:52:12 2014, Thomas Bergauer, , important web pages, , , , , Unknown
|
SPS Accelerator status: http://op-webtools.web.cern.ch/op-webtools/vistar/vistars.php?usr=SPS1
general Information about the Beam line(s): http://sba.web.cern.ch/sba/ |
|
Sat Nov 15 11:36:41 2014, Thomas Bergauer, common, Checklist for North Area access, , , , , Unknown
|
Checklist for North Area access:
- Dosimeter (http://dosimetry.web.cern.ch/en
 )
- Helmet and safety shoes (http://gs-dep.web.cern.ch/en/content/stores_hours)
- Access right to H6A control room (request via EDH): Control Room HNA-447 (0887-1-Q45). Activate access right on your CERN access card at one of the validation stations (https://espace.cern.ch/service-access-control/default.aspx)
- For using CERN rental car, request "CERN vehicle driving license (V)" via EDH
- Park in front of bldg. 890. Walk to North Hall (bldg. 887) through bldg. 907. Swipe dosimeter in front of electronic lock next to the entrance door. Turn left inside bldg. 887. Control room Q45 is on the left-hand side of the upper level. Swipe CERN access card in front of electronic lock.
|
|
Sat Nov 15 11:37:19 2014, Thomas Bergauer, AIDA, List of EUDET Telescope PCs in H6b, , , , , Unknown
|
https://twiki.cern.ch/twiki/bin/view/CLIC/ClicPixelDataTakingCERNPS2014 |
|
Sat Nov 15 12:41:50 2014, Benedikt Würkner, Belle SVD, Discoveries during preliminary sensor tests, , , , , Unknown
|
L5_p_side APV #3 faulty signal
L4_n_side APV #2 and #3 faulty signal |
|
Sun Nov 16 14:22:51 2014, Thomas Bergauer, AIDA, PC Configuration EUDET Telescope in H6b, , , , , Unknown
|
PC (gehört AIDA) in H6b control room: ssh telescope@pcaidatb.cern.ch
|
|
Sun Nov 16 21:37:56 2014, Hao Yin, common, AIM, , , , , Unknown
|
fachi: aimhephy@antispam.e4ward.com
chrisu: gargamel0971
flo: flo.bux@sbg.at
shorty: martin@kurznet.net
markus; mueffi1040
hao: hao.yin@gmx.at
benni: benedikt.wuerkner@assoc.oeaw.ac.at
juan: juan.garcia.ferrero@cern.ch
axel: ???
bergi: callmebergi |
|
Mon Nov 17 19:23:57 2014, Thomas Bergauer, Infineon, PI XY table initial position, , , , , Unknown
|
initial position of Infineon Stack (PI Micromove):
(guess center position by eye)
STRIPS IN HORIZONTAL DIRECTION
* vertical axis: M511.DD: Zero position 81.0mm / higher values correspond to lowering the table
* vertical axis: M521.DD: Zero position 96.0mm / higher values correspond to move the table to the table mounting |
|
Mon Nov 17 22:03:02 2014, Martin Kurz, common, Drucker, , , , , Unknown
|
Drucken über den Printserver (192.168.0.150):
MAC:
direkt über den universellen AirPrint Treiber oder mittels Treiber vom Gerätehersteller drucken.
Einfach nach Druckern suchen. Druckername: CanonMP630 @ higgscms
LINUX:
Eine Datei Names (/etc/cups/client.conf) mit dem Inhalt folgenden Inhalt -ohne Anführungszeichen- erstellen: "ServerName 192.168.0.150"
--> sofort steht der Drucker mit allen richtigen Einstellungen zur Verfügung
Drucken mittels Treiber vom Gerätehersteller ist weiterhin möglich. (wird von CUPS automatisch zur Verfügung gestellt) CUPS URL: "http://192.168.0.150:631/printers/CanonMP630"
WINDOWS:
1.) Unter Start->Einstellungen->Drucker und Faxgeräte links den Punkt “neuen Drucker hinzufügen” auswählen.
2.) In dem sich öffnenden Assistenten die Option “Netzwerkdrucker hinzufügen” auswählen und auf “weiter” klicken.
3.) Zunächst den Punkt “Verbindung mit einem Drucker im Internet herstellen” auswählen und dann die "URL" zum Drucker einfügen.
Name: http://192.168.0.150:631/printers/CanonMP630
|
|
Tue Nov 18 12:35:32 2014, Axel König, common, Infineon (4 modules) TLU Settings, , , , , Unknown
|
- VNC to 192.168.0.18
- In command line: cd C:\Users\telescope\eudaq\bin
- TLUControl.exe.exe -d 2 -a 11 - i RJ45
Operating with AIDA telescope: TLUControl.exe.exe -d 3 -a 11 - i RJ45
Dut Position (left to right): 11, 06, 05, 07 |
|