| ID |
Date |
Author |
Subject |
Run Number |
DUT |
Beam Energy |
Rate Setting |
Particle Type |
Data |
t-Start |
t-Stop |
Duration_min |
Frontend |
|
56
|
Sat Mar 30 16:09:54 2024 |
hh, mb, ps | 1st tests | 1039 | TJ-Monopix2 | 800 MeV | Low Flux Low | Proton | Unknown | 30.03.2024 16:11:32 | 30.03.2024 16:12:21 | 0 | HV | automatic log for run 1039
Comment: |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 0
HDMI2_clk = 1
HDMI3_clk = 0
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xC
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x00 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x3 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_AB]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_AB
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_AB]
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_AB_$12D$X
DISABLE_PRINT = 1
[Producer.tjmonopix2_CD]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_CD
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_CD]
EUDAQ_MN = monopix2_mon
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_CD_$12D$X
DISABLE_PRINT = 1
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
6
|
Sat Mar 30 07:11:30 2024 |
bp, ci, hh | RD50-MPW4 | 1003 | RD50-MPW4 | 800 MeV | Low Flux Very Low | Proton | Unknown | 30.03.2024 07:12:19 | 30.03.2024 07:13:57 | 1 | Normal | automatic log for run 1003
Comment:
1st test runs |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib_base.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_hitbus_dcols =
en_sfout_dcol = 0
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-9
inj_t0 = 511
matrix_config = matrix_mpw4.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 3
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
inj__u = 0
inj__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 0.92
th__i = 3
|
| Attachment 2: matrix_mpw4.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {masked} {en_inj} {en_hb} {en_sfout} {trimDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 0 0 0 0 13
00 01 0 0 0 0 4
00 02 0 0 0 0 9
00 03 0 0 0 0 12
00 04 0 0 0 0 7
00 05 0 0 0 0 10
00 06 0 0 0 0 8
00 07 0 0 0 0 8
00 08 0 0 0 0 8
00 09 0 0 0 0 9
00 10 0 0 0 0 10
00 11 0 0 0 0 5
00 12 0 0 0 0 14
00 13 0 0 0 0 6
00 14 0 0 0 0 7
00 15 0 0 0 0 3
00 16 0 0 0 0 5
00 17 0 0 0 0 15
00 18 0 0 0 0 12
00 19 0 0 0 0 11
00 20 0 0 0 0 6
00 21 0 0 0 0 5
00 22 0 0 0 0 7
00 23 0 0 0 0 6
00 24 0 0 0 0 10
00 25 0 0 0 0 4
00 26 0 0 0 0 6
00 27 0 0 0 0 0
00 28 0 0 0 0 6
00 29 0 0 0 0 6
00 30 0 0 0 0 11
00 31 0 0 0 0 3
00 32 0 0 0 0 6
00 33 0 0 0 0 8
00 34 0 0 0 0 9
00 35 0 0 0 0 8
00 36 0 0 0 0 11
00 37 0 0 0 0 8
00 38 0 0 0 0 11
00 39 0 0 0 0 8
00 40 0 0 0 0 13
00 41 0 0 0 0 8
00 42 0 0 0 0 7
00 43 0 0 0 0 5
00 44 0 0 0 0 10
00 45 0 0 0 0 14
00 46 0 0 0 0 3
00 47 0 0 0 0 8
00 48 0 0 0 0 7
00 49 0 0 0 0 7
00 50 0 0 0 0 5
00 51 0 0 0 0 8
00 52 0 0 0 0 11
00 53 0 0 0 0 7
00 54 0 0 0 0 8
00 55 0 0 0 0 10
00 56 0 0 0 0 11
00 57 0 0 0 0 6
00 58 0 0 0 0 11
00 59 0 0 0 0 4
00 60 0 0 0 0 8
00 61 0 0 0 0 5
00 62 1 0 0 0 10
00 63 0 0 0 0 9
01 00 0 0 0 0 15
01 01 0 0 0 0 10
01 02 0 0 0 0 8
01 03 0 0 0 0 7
01 04 0 0 0 0 10
01 05 0 0 0 0 0
01 06 0 0 0 0 10
01 07 0 0 0 0 15
01 08 0 0 0 0 4
01 09 0 0 0 0 13
01 10 0 0 0 0 9
01 11 0 0 0 0 4
01 12 0 0 0 0 12
01 13 0 0 0 0 11
01 14 0 0 0 0 7
01 15 0 0 0 0 2
01 16 0 0 0 0 7
01 17 0 0 0 0 12
01 18 0 0 0 0 6
01 19 0 0 0 0 10
01 20 0 0 0 0 9
01 21 0 0 0 0 13
01 22 0 0 0 0 6
01 23 0 0 0 0 12
01 24 0 0 0 0 5
01 25 0 0 0 0 10
01 26 0 0 0 0 9
01 27 0 0 0 0 9
01 28 0 0 0 0 5
01 29 0 0 0 0 4
01 30 0 0 0 0 9
01 31 0 0 0 0 6
01 32 0 0 0 0 10
01 33 0 0 0 0 5
01 34 1 0 0 0 15
01 35 0 0 0 0 8
01 36 0 0 0 0 4
01 37 0 0 0 0 7
01 38 0 0 0 0 12
01 39 0 0 0 0 8
01 40 0 0 0 0 9
01 41 0 0 0 0 4
01 42 0 0 0 0 12
01 43 0 0 0 0 6
01 44 0 0 0 0 6
01 45 0 0 0 0 13
01 46 0 0 0 0 12
01 47 0 0 0 0 8
01 48 0 0 0 0 4
01 49 0 0 0 0 10
01 50 0 0 0 0 10
01 51 0 0 0 0 8
01 52 0 0 0 0 10
01 53 0 0 0 0 11
01 54 0 0 0 0 11
01 55 0 0 0 0 4
01 56 0 0 0 0 13
01 57 0 0 0 0 12
01 58 0 0 0 0 4
01 59 0 0 0 0 5
01 60 0 0 0 0 9
01 61 0 0 0 0 7
01 62 0 0 0 0 7
01 63 0 0 0 0 10
02 00 0 0 0 0 6
02 01 0 0 0 0 11
02 02 0 0 0 0 14
02 03 0 0 0 0 8
02 04 0 0 0 0 11
02 05 0 0 0 0 14
02 06 0 0 0 0 11
02 07 0 0 0 0 12
02 08 0 0 0 0 7
02 09 0 0 0 0 10
02 10 0 0 0 0 6
02 11 0 0 0 0 7
02 12 0 0 0 0 9
02 13 0 0 0 0 5
02 14 0 0 0 0 8
02 15 0 0 0 0 6
02 16 0 0 0 0 10
02 17 0 0 0 0 10
02 18 0 0 0 0 10
02 19 0 0 0 0 8
02 20 0 0 0 0 9
02 21 0 0 0 0 7
02 22 0 0 0 0 4
02 23 0 0 0 0 7
02 24 0 0 0 0 12
02 25 0 0 0 0 2
02 26 0 0 0 0 2
02 27 0 0 0 0 9
02 28 0 0 0 0 7
02 29 0 0 0 0 8
02 30 0 0 0 0 9
02 31 0 0 0 0 11
02 32 0 0 0 0 7
02 33 0 0 0 0 9
02 34 0 0 0 0 6
02 35 1 0 0 0 10
02 36 0 0 0 0 10
02 37 0 0 0 0 14
02 38 0 0 0 0 7
02 39 0 0 0 0 7
02 40 0 0 0 0 7
02 41 0 0 0 0 9
02 42 0 0 0 0 6
02 43 0 0 0 0 9
02 44 0 0 0 0 4
02 45 0 0 0 0 10
02 46 0 0 0 0 12
02 47 0 0 0 0 8
02 48 0 0 0 0 5
02 49 0 0 0 0 12
02 50 0 0 0 0 5
02 51 0 0 0 0 9
02 52 0 0 0 0 6
02 53 0 0 0 0 5
02 54 0 0 0 0 6
02 55 0 0 0 0 8
02 56 0 0 0 0 4
02 57 0 0 0 0 7
02 58 0 0 0 0 15
02 59 0 0 0 0 15
02 60 0 0 0 0 8
02 61 0 0 0 0 9
02 62 0 0 0 0 12
02 63 0 0 0 0 8
03 00 0 0 0 0 8
03 01 0 0 0 0 11
03 02 0 0 0 0 5
03 03 0 0 0 0 2
03 04 0 0 0 0 6
03 05 0 0 0 0 9
03 06 0 0 0 0 6
03 07 0 0 0 0 7
03 08 0 0 0 0 8
03 09 0 0 0 0 8
03 10 0 0 0 0 6
03 11 0 0 0 0 5
03 12 0 0 0 0 12
03 13 0 0 0 0 3
03 14 0 0 0 0 9
03 15 0 0 0 0 1
03 16 0 0 0 0 6
03 17 0 0 0 0 13
03 18 0 0 0 0 15
03 19 0 0 0 0 8
03 20 0 0 0 0 8
03 21 0 0 0 0 6
03 22 0 0 0 0 7
03 23 0 0 0 0 8
03 24 0 0 0 0 4
03 25 0 0 0 0 5
03 26 0 0 0 0 6
03 27 0 0 0 0 5
03 28 0 0 0 0 11
03 29 0 0 0 0 9
03 30 0 0 0 0 6
03 31 0 0 0 0 12
03 32 0 0 0 0 6
03 33 0 0 0 0 6
03 34 0 0 0 0 9
03 35 0 0 0 0 6
03 36 0 0 0 0 10
03 37 0 0 0 0 11
03 38 0 0 0 0 10
03 39 0 0 0 0 10
03 40 0 0 0 0 4
03 41 0 0 0 0 8
03 42 0 0 0 0 12
03 43 0 0 0 0 12
03 44 0 0 0 0 9
03 45 0 0 0 0 12
03 46 0 0 0 0 9
03 47 0 0 0 0 3
03 48 0 0 0 0 9
03 49 0 0 0 0 7
03 50 0 0 0 0 1
03 51 0 0 0 0 8
03 52 0 0 0 0 9
03 53 0 0 0 0 10
03 54 0 0 0 0 4
03 55 0 0 0 0 3
03 56 0 0 0 0 12
03 57 0 0 0 0 5
03 58 0 0 0 0 4
03 59 0 0 0 0 7
03 60 1 0 0 0 8
03 61 0 0 0 0 8
03 62 0 0 0 0 8
03 63 0 0 0 0 1
04 00 0 0 0 0 8
04 01 0 0 0 0 15
04 02 0 0 0 0 12
04 03 0 0 0 0 4
04 04 0 0 0 0 9
04 05 0 0 0 0 11
04 06 0 0 0 0 14
04 07 0 0 0 0 10
04 08 0 0 0 0 4
04 09 0 0 0 0 7
04 10 0 0 0 0 8
04 11 0 0 0 0 11
04 12 0 0 0 0 9
04 13 0 0 0 0 11
04 14 0 0 0 0 7
04 15 0 0 0 0 10
04 16 0 0 0 0 3
04 17 0 0 0 0 10
04 18 0 0 0 0 11
04 19 0 0 0 0 12
04 20 0 0 0 0 10
04 21 0 0 0 0 11
04 22 0 0 0 0 8
04 23 0 0 0 0 11
04 24 0 0 0 0 2
04 25 0 0 0 0 3
04 26 0 0 0 0 9
04 27 0 0 0 0 11
04 28 0 0 0 0 7
04 29 0 0 0 0 4
04 30 0 0 0 0 5
04 31 0 0 0 0 9
04 32 0 0 0 0 4
04 33 0 0 0 0 8
04 34 0 0 0 0 7
04 35 0 0 0 0 3
04 36 0 0 0 0 4
04 37 0 0 0 0 10
... 3802 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x0 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/MPW4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
33
|
Sat Mar 30 10:27:56 2024 |
bp, ci, hh | RD50-MPW4 | 1019 | RD50-MPW4 | 800 MeV | Low Flux Low | Proton | Crap | 30.03.2024 10:28:28 | 30.03.2024 10:30:22 | 1 | Normal | automatic log for run 1019
Comment: |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib_base.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_hitbus_dcols =
en_sfout_dcol = 0
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-9
inj_t0 = 511
matrix_config = matrix_mpw4.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 3
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
inj__u = 0
inj__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 0.92
th__i = 3
|
| Attachment 2: matrix_mpw4.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {masked} {en_inj} {en_hb} {en_sfout} {trimDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 0 0 0 0 13
00 01 0 0 0 0 4
00 02 0 0 0 0 9
00 03 0 0 0 0 12
00 04 0 0 0 0 7
00 05 0 0 0 0 10
00 06 0 0 0 0 8
00 07 0 0 0 0 8
00 08 0 0 0 0 8
00 09 0 0 0 0 9
00 10 0 0 0 0 10
00 11 0 0 0 0 5
00 12 0 0 0 0 14
00 13 0 0 0 0 6
00 14 0 0 0 0 7
00 15 0 0 0 0 3
00 16 0 0 0 0 5
00 17 0 0 0 0 15
00 18 0 0 0 0 12
00 19 0 0 0 0 11
00 20 0 0 0 0 6
00 21 0 0 0 0 5
00 22 0 0 0 0 7
00 23 0 0 0 0 6
00 24 0 0 0 0 10
00 25 0 0 0 0 4
00 26 0 0 0 0 6
00 27 0 0 0 0 0
00 28 0 0 0 0 6
00 29 0 0 0 0 6
00 30 0 0 0 0 11
00 31 0 0 0 0 3
00 32 0 0 0 0 6
00 33 0 0 0 0 8
00 34 0 0 0 0 9
00 35 0 0 0 0 8
00 36 0 0 0 0 11
00 37 0 0 0 0 8
00 38 0 0 0 0 11
00 39 0 0 0 0 8
00 40 0 0 0 0 13
00 41 0 0 0 0 8
00 42 0 0 0 0 7
00 43 0 0 0 0 5
00 44 0 0 0 0 10
00 45 0 0 0 0 14
00 46 0 0 0 0 3
00 47 0 0 0 0 8
00 48 0 0 0 0 7
00 49 0 0 0 0 7
00 50 0 0 0 0 5
00 51 0 0 0 0 8
00 52 0 0 0 0 11
00 53 0 0 0 0 7
00 54 0 0 0 0 8
00 55 0 0 0 0 10
00 56 0 0 0 0 11
00 57 0 0 0 0 6
00 58 0 0 0 0 11
00 59 0 0 0 0 4
00 60 0 0 0 0 8
00 61 0 0 0 0 5
00 62 1 0 0 0 10
00 63 0 0 0 0 9
01 00 0 0 0 0 15
01 01 0 0 0 0 10
01 02 0 0 0 0 8
01 03 0 0 0 0 7
01 04 0 0 0 0 10
01 05 0 0 0 0 0
01 06 0 0 0 0 10
01 07 0 0 0 0 15
01 08 0 0 0 0 4
01 09 0 0 0 0 13
01 10 0 0 0 0 9
01 11 0 0 0 0 4
01 12 0 0 0 0 12
01 13 0 0 0 0 11
01 14 0 0 0 0 7
01 15 0 0 0 0 2
01 16 0 0 0 0 7
01 17 0 0 0 0 12
01 18 0 0 0 0 6
01 19 0 0 0 0 10
01 20 0 0 0 0 9
01 21 0 0 0 0 13
01 22 0 0 0 0 6
01 23 0 0 0 0 12
01 24 0 0 0 0 5
01 25 0 0 0 0 10
01 26 0 0 0 0 9
01 27 0 0 0 0 9
01 28 0 0 0 0 5
01 29 0 0 0 0 4
01 30 0 0 0 0 9
01 31 0 0 0 0 6
01 32 0 0 0 0 10
01 33 0 0 0 0 5
01 34 1 0 0 0 15
01 35 0 0 0 0 8
01 36 0 0 0 0 4
01 37 0 0 0 0 7
01 38 0 0 0 0 12
01 39 0 0 0 0 8
01 40 0 0 0 0 9
01 41 0 0 0 0 4
01 42 0 0 0 0 12
01 43 0 0 0 0 6
01 44 0 0 0 0 6
01 45 0 0 0 0 13
01 46 0 0 0 0 12
01 47 0 0 0 0 8
01 48 0 0 0 0 4
01 49 0 0 0 0 10
01 50 0 0 0 0 10
01 51 0 0 0 0 8
01 52 0 0 0 0 10
01 53 0 0 0 0 11
01 54 0 0 0 0 11
01 55 0 0 0 0 4
01 56 0 0 0 0 13
01 57 0 0 0 0 12
01 58 0 0 0 0 4
01 59 0 0 0 0 5
01 60 0 0 0 0 9
01 61 0 0 0 0 7
01 62 0 0 0 0 7
01 63 0 0 0 0 10
02 00 0 0 0 0 6
02 01 0 0 0 0 11
02 02 0 0 0 0 14
02 03 0 0 0 0 8
02 04 0 0 0 0 11
02 05 0 0 0 0 14
02 06 0 0 0 0 11
02 07 0 0 0 0 12
02 08 0 0 0 0 7
02 09 0 0 0 0 10
02 10 0 0 0 0 6
02 11 0 0 0 0 7
02 12 0 0 0 0 9
02 13 0 0 0 0 5
02 14 0 0 0 0 8
02 15 0 0 0 0 6
02 16 0 0 0 0 10
02 17 0 0 0 0 10
02 18 0 0 0 0 10
02 19 0 0 0 0 8
02 20 0 0 0 0 9
02 21 0 0 0 0 7
02 22 0 0 0 0 4
02 23 0 0 0 0 7
02 24 0 0 0 0 12
02 25 0 0 0 0 2
02 26 0 0 0 0 2
02 27 0 0 0 0 9
02 28 0 0 0 0 7
02 29 0 0 0 0 8
02 30 0 0 0 0 9
02 31 0 0 0 0 11
02 32 0 0 0 0 7
02 33 0 0 0 0 9
02 34 0 0 0 0 6
02 35 1 0 0 0 10
02 36 0 0 0 0 10
02 37 0 0 0 0 14
02 38 0 0 0 0 7
02 39 0 0 0 0 7
02 40 0 0 0 0 7
02 41 0 0 0 0 9
02 42 0 0 0 0 6
02 43 0 0 0 0 9
02 44 0 0 0 0 4
02 45 0 0 0 0 10
02 46 0 0 0 0 12
02 47 0 0 0 0 8
02 48 0 0 0 0 5
02 49 0 0 0 0 12
02 50 0 0 0 0 5
02 51 0 0 0 0 9
02 52 0 0 0 0 6
02 53 0 0 0 0 5
02 54 0 0 0 0 6
02 55 0 0 0 0 8
02 56 0 0 0 0 4
02 57 0 0 0 0 7
02 58 0 0 0 0 15
02 59 0 0 0 0 15
02 60 0 0 0 0 8
02 61 0 0 0 0 9
02 62 0 0 0 0 12
02 63 0 0 0 0 8
03 00 0 0 0 0 8
03 01 0 0 0 0 11
03 02 0 0 0 0 5
03 03 0 0 0 0 2
03 04 0 0 0 0 6
03 05 0 0 0 0 9
03 06 0 0 0 0 6
03 07 0 0 0 0 7
03 08 0 0 0 0 8
03 09 0 0 0 0 8
03 10 0 0 0 0 6
03 11 0 0 0 0 5
03 12 0 0 0 0 12
03 13 0 0 0 0 3
03 14 0 0 0 0 9
03 15 0 0 0 0 1
03 16 0 0 0 0 6
03 17 0 0 0 0 13
03 18 0 0 0 0 15
03 19 0 0 0 0 8
03 20 0 0 0 0 8
03 21 0 0 0 0 6
03 22 0 0 0 0 7
03 23 0 0 0 0 8
03 24 0 0 0 0 4
03 25 0 0 0 0 5
03 26 0 0 0 0 6
03 27 0 0 0 0 5
03 28 0 0 0 0 11
03 29 0 0 0 0 9
03 30 0 0 0 0 6
03 31 0 0 0 0 12
03 32 0 0 0 0 6
03 33 0 0 0 0 6
03 34 0 0 0 0 9
03 35 0 0 0 0 6
03 36 0 0 0 0 10
03 37 0 0 0 0 11
03 38 0 0 0 0 10
03 39 0 0 0 0 10
03 40 0 0 0 0 4
03 41 0 0 0 0 8
03 42 0 0 0 0 12
03 43 0 0 0 0 12
03 44 0 0 0 0 9
03 45 0 0 0 0 12
03 46 0 0 0 0 9
03 47 0 0 0 0 3
03 48 0 0 0 0 9
03 49 0 0 0 0 7
03 50 0 0 0 0 1
03 51 0 0 0 0 8
03 52 0 0 0 0 9
03 53 0 0 0 0 10
03 54 0 0 0 0 4
03 55 0 0 0 0 3
03 56 0 0 0 0 12
03 57 0 0 0 0 5
03 58 0 0 0 0 4
03 59 0 0 0 0 7
03 60 1 0 0 0 8
03 61 0 0 0 0 8
03 62 0 0 0 0 8
03 63 0 0 0 0 1
04 00 0 0 0 0 8
04 01 0 0 0 0 15
04 02 0 0 0 0 12
04 03 0 0 0 0 4
04 04 0 0 0 0 9
04 05 0 0 0 0 11
04 06 0 0 0 0 14
04 07 0 0 0 0 10
04 08 0 0 0 0 4
04 09 0 0 0 0 7
04 10 0 0 0 0 8
04 11 0 0 0 0 11
04 12 0 0 0 0 9
04 13 0 0 0 0 11
04 14 0 0 0 0 7
04 15 0 0 0 0 10
04 16 0 0 0 0 3
04 17 0 0 0 0 10
04 18 0 0 0 0 11
04 19 0 0 0 0 12
04 20 0 0 0 0 10
04 21 0 0 0 0 11
04 22 0 0 0 0 8
04 23 0 0 0 0 11
04 24 0 0 0 0 2
04 25 0 0 0 0 3
04 26 0 0 0 0 9
04 27 0 0 0 0 11
04 28 0 0 0 0 7
04 29 0 0 0 0 4
04 30 0 0 0 0 5
04 31 0 0 0 0 9
04 32 0 0 0 0 4
04 33 0 0 0 0 8
04 34 0 0 0 0 7
04 35 0 0 0 0 3
04 36 0 0 0 0 4
04 37 0 0 0 0 10
... 3802 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x0 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/MPW4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
48
|
Sat Mar 30 15:20:37 2024 |
hh, mb, ps | 1st tests | 1031 | TJ-Monopix2 | 800 MeV | Low Flux Low | Proton | Unknown | 30.03.2024 15:21:51 | 30.03.2024 15:23:03 | 1 | HV | automatic log for run 1031
Comment: |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 0
HDMI2_clk = 1
HDMI3_clk = 0
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xB
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x00 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x3 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_AB]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_AB
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_AB]
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_AB_$12D$X
DISABLE_PRINT = 1
[Producer.tjmonopix2_CD]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_CD
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_CD]
EUDAQ_MN = monopix2_mon
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_CD_$12D$X
DISABLE_PRINT = 1
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
64
|
Sat Mar 30 18:59:16 2024 |
hh, mb, ps | 1st tests | 1047 | TJ-Monopix2 | 800 MeV | Low Flux Low | Proton | Crap | 30.03.2024 19:00:11 | 30.03.2024 19:01:43 | 1 | HV | automatic log for run 1047
Comment:
Test if we get beam, MAUS has problems |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 0
HDMI2_clk = 0
HDMI3_clk = 0
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xA
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x00 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x0 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_AB]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_AB
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_AB]
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_AB_$12D$X
DISABLE_PRINT = 1
[Producer.tjmonopix2_CD]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_CD
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_CD]
EUDAQ_MN = monopix2_mon
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_CD_$12D$X
DISABLE_PRINT = 1
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
7
|
Sat Mar 30 07:22:49 2024 |
bp, ci, hh | RD50-MPW4 | 1004 | RD50-MPW4 | 800 MeV | Low Flux Very Low | Proton | Unknown | 30.03.2024 07:14:51 | 30.03.2024 07:25:16 | 10 | Normal | automatic log for run 1004
Comment:
1st test runs |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib_base.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_hitbus_dcols =
en_sfout_dcol = 0
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-9
inj_t0 = 511
matrix_config = matrix_mpw4.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 3
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
inj__u = 0
inj__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 0.92
th__i = 3
|
| Attachment 2: matrix_mpw4.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {masked} {en_inj} {en_hb} {en_sfout} {trimDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 0 0 0 0 13
00 01 0 0 0 0 4
00 02 0 0 0 0 9
00 03 0 0 0 0 12
00 04 0 0 0 0 7
00 05 0 0 0 0 10
00 06 0 0 0 0 8
00 07 0 0 0 0 8
00 08 0 0 0 0 8
00 09 0 0 0 0 9
00 10 0 0 0 0 10
00 11 0 0 0 0 5
00 12 0 0 0 0 14
00 13 0 0 0 0 6
00 14 0 0 0 0 7
00 15 0 0 0 0 3
00 16 0 0 0 0 5
00 17 0 0 0 0 15
00 18 0 0 0 0 12
00 19 0 0 0 0 11
00 20 0 0 0 0 6
00 21 0 0 0 0 5
00 22 0 0 0 0 7
00 23 0 0 0 0 6
00 24 0 0 0 0 10
00 25 0 0 0 0 4
00 26 0 0 0 0 6
00 27 0 0 0 0 0
00 28 0 0 0 0 6
00 29 0 0 0 0 6
00 30 0 0 0 0 11
00 31 0 0 0 0 3
00 32 0 0 0 0 6
00 33 0 0 0 0 8
00 34 0 0 0 0 9
00 35 0 0 0 0 8
00 36 0 0 0 0 11
00 37 0 0 0 0 8
00 38 0 0 0 0 11
00 39 0 0 0 0 8
00 40 0 0 0 0 13
00 41 0 0 0 0 8
00 42 0 0 0 0 7
00 43 0 0 0 0 5
00 44 0 0 0 0 10
00 45 0 0 0 0 14
00 46 0 0 0 0 3
00 47 0 0 0 0 8
00 48 0 0 0 0 7
00 49 0 0 0 0 7
00 50 0 0 0 0 5
00 51 0 0 0 0 8
00 52 0 0 0 0 11
00 53 0 0 0 0 7
00 54 0 0 0 0 8
00 55 0 0 0 0 10
00 56 0 0 0 0 11
00 57 0 0 0 0 6
00 58 0 0 0 0 11
00 59 0 0 0 0 4
00 60 0 0 0 0 8
00 61 0 0 0 0 5
00 62 1 0 0 0 10
00 63 0 0 0 0 9
01 00 0 0 0 0 15
01 01 0 0 0 0 10
01 02 0 0 0 0 8
01 03 0 0 0 0 7
01 04 0 0 0 0 10
01 05 0 0 0 0 0
01 06 0 0 0 0 10
01 07 0 0 0 0 15
01 08 0 0 0 0 4
01 09 0 0 0 0 13
01 10 0 0 0 0 9
01 11 0 0 0 0 4
01 12 0 0 0 0 12
01 13 0 0 0 0 11
01 14 0 0 0 0 7
01 15 0 0 0 0 2
01 16 0 0 0 0 7
01 17 0 0 0 0 12
01 18 0 0 0 0 6
01 19 0 0 0 0 10
01 20 0 0 0 0 9
01 21 0 0 0 0 13
01 22 0 0 0 0 6
01 23 0 0 0 0 12
01 24 0 0 0 0 5
01 25 0 0 0 0 10
01 26 0 0 0 0 9
01 27 0 0 0 0 9
01 28 0 0 0 0 5
01 29 0 0 0 0 4
01 30 0 0 0 0 9
01 31 0 0 0 0 6
01 32 0 0 0 0 10
01 33 0 0 0 0 5
01 34 1 0 0 0 15
01 35 0 0 0 0 8
01 36 0 0 0 0 4
01 37 0 0 0 0 7
01 38 0 0 0 0 12
01 39 0 0 0 0 8
01 40 0 0 0 0 9
01 41 0 0 0 0 4
01 42 0 0 0 0 12
01 43 0 0 0 0 6
01 44 0 0 0 0 6
01 45 0 0 0 0 13
01 46 0 0 0 0 12
01 47 0 0 0 0 8
01 48 0 0 0 0 4
01 49 0 0 0 0 10
01 50 0 0 0 0 10
01 51 0 0 0 0 8
01 52 0 0 0 0 10
01 53 0 0 0 0 11
01 54 0 0 0 0 11
01 55 0 0 0 0 4
01 56 0 0 0 0 13
01 57 0 0 0 0 12
01 58 0 0 0 0 4
01 59 0 0 0 0 5
01 60 0 0 0 0 9
01 61 0 0 0 0 7
01 62 0 0 0 0 7
01 63 0 0 0 0 10
02 00 0 0 0 0 6
02 01 0 0 0 0 11
02 02 0 0 0 0 14
02 03 0 0 0 0 8
02 04 0 0 0 0 11
02 05 0 0 0 0 14
02 06 0 0 0 0 11
02 07 0 0 0 0 12
02 08 0 0 0 0 7
02 09 0 0 0 0 10
02 10 0 0 0 0 6
02 11 0 0 0 0 7
02 12 0 0 0 0 9
02 13 0 0 0 0 5
02 14 0 0 0 0 8
02 15 0 0 0 0 6
02 16 0 0 0 0 10
02 17 0 0 0 0 10
02 18 0 0 0 0 10
02 19 0 0 0 0 8
02 20 0 0 0 0 9
02 21 0 0 0 0 7
02 22 0 0 0 0 4
02 23 0 0 0 0 7
02 24 0 0 0 0 12
02 25 0 0 0 0 2
02 26 0 0 0 0 2
02 27 0 0 0 0 9
02 28 0 0 0 0 7
02 29 0 0 0 0 8
02 30 0 0 0 0 9
02 31 0 0 0 0 11
02 32 0 0 0 0 7
02 33 0 0 0 0 9
02 34 0 0 0 0 6
02 35 1 0 0 0 10
02 36 0 0 0 0 10
02 37 0 0 0 0 14
02 38 0 0 0 0 7
02 39 0 0 0 0 7
02 40 0 0 0 0 7
02 41 0 0 0 0 9
02 42 0 0 0 0 6
02 43 0 0 0 0 9
02 44 0 0 0 0 4
02 45 0 0 0 0 10
02 46 0 0 0 0 12
02 47 0 0 0 0 8
02 48 0 0 0 0 5
02 49 0 0 0 0 12
02 50 0 0 0 0 5
02 51 0 0 0 0 9
02 52 0 0 0 0 6
02 53 0 0 0 0 5
02 54 0 0 0 0 6
02 55 0 0 0 0 8
02 56 0 0 0 0 4
02 57 0 0 0 0 7
02 58 0 0 0 0 15
02 59 0 0 0 0 15
02 60 0 0 0 0 8
02 61 0 0 0 0 9
02 62 0 0 0 0 12
02 63 0 0 0 0 8
03 00 0 0 0 0 8
03 01 0 0 0 0 11
03 02 0 0 0 0 5
03 03 0 0 0 0 2
03 04 0 0 0 0 6
03 05 0 0 0 0 9
03 06 0 0 0 0 6
03 07 0 0 0 0 7
03 08 0 0 0 0 8
03 09 0 0 0 0 8
03 10 0 0 0 0 6
03 11 0 0 0 0 5
03 12 0 0 0 0 12
03 13 0 0 0 0 3
03 14 0 0 0 0 9
03 15 0 0 0 0 1
03 16 0 0 0 0 6
03 17 0 0 0 0 13
03 18 0 0 0 0 15
03 19 0 0 0 0 8
03 20 0 0 0 0 8
03 21 0 0 0 0 6
03 22 0 0 0 0 7
03 23 0 0 0 0 8
03 24 0 0 0 0 4
03 25 0 0 0 0 5
03 26 0 0 0 0 6
03 27 0 0 0 0 5
03 28 0 0 0 0 11
03 29 0 0 0 0 9
03 30 0 0 0 0 6
03 31 0 0 0 0 12
03 32 0 0 0 0 6
03 33 0 0 0 0 6
03 34 0 0 0 0 9
03 35 0 0 0 0 6
03 36 0 0 0 0 10
03 37 0 0 0 0 11
03 38 0 0 0 0 10
03 39 0 0 0 0 10
03 40 0 0 0 0 4
03 41 0 0 0 0 8
03 42 0 0 0 0 12
03 43 0 0 0 0 12
03 44 0 0 0 0 9
03 45 0 0 0 0 12
03 46 0 0 0 0 9
03 47 0 0 0 0 3
03 48 0 0 0 0 9
03 49 0 0 0 0 7
03 50 0 0 0 0 1
03 51 0 0 0 0 8
03 52 0 0 0 0 9
03 53 0 0 0 0 10
03 54 0 0 0 0 4
03 55 0 0 0 0 3
03 56 0 0 0 0 12
03 57 0 0 0 0 5
03 58 0 0 0 0 4
03 59 0 0 0 0 7
03 60 1 0 0 0 8
03 61 0 0 0 0 8
03 62 0 0 0 0 8
03 63 0 0 0 0 1
04 00 0 0 0 0 8
04 01 0 0 0 0 15
04 02 0 0 0 0 12
04 03 0 0 0 0 4
04 04 0 0 0 0 9
04 05 0 0 0 0 11
04 06 0 0 0 0 14
04 07 0 0 0 0 10
04 08 0 0 0 0 4
04 09 0 0 0 0 7
04 10 0 0 0 0 8
04 11 0 0 0 0 11
04 12 0 0 0 0 9
04 13 0 0 0 0 11
04 14 0 0 0 0 7
04 15 0 0 0 0 10
04 16 0 0 0 0 3
04 17 0 0 0 0 10
04 18 0 0 0 0 11
04 19 0 0 0 0 12
04 20 0 0 0 0 10
04 21 0 0 0 0 11
04 22 0 0 0 0 8
04 23 0 0 0 0 11
04 24 0 0 0 0 2
04 25 0 0 0 0 3
04 26 0 0 0 0 9
04 27 0 0 0 0 11
04 28 0 0 0 0 7
04 29 0 0 0 0 4
04 30 0 0 0 0 5
04 31 0 0 0 0 9
04 32 0 0 0 0 4
04 33 0 0 0 0 8
04 34 0 0 0 0 7
04 35 0 0 0 0 3
04 36 0 0 0 0 4
04 37 0 0 0 0 10
... 3802 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x0 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/MPW4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
66
|
Sat Mar 30 19:36:57 2024 |
hh, mb, ps | High statistics | 1049 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Unknown | 30.03.2024 19:28:44 | 30.03.2024 19:39:24 | 10 | HV | automatic log for run 1049
Comment:
Try with increased veto period of 20us (800) |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 0
HDMI2_clk = 0
HDMI3_clk = 0
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xA
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x00 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x0 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_AB]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_AB
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_AB]
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_AB_$12D$X
DISABLE_PRINT = 1
[Producer.tjmonopix2_CD]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_CD
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_CD]
EUDAQ_MN = monopix2_mon
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_CD_$12D$X
DISABLE_PRINT = 1
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
44
|
Sat Mar 30 15:02:07 2024 |
hh, mb, ps | 1st tests | 1027 | TJ-Monopix2 | 800 MeV | Low Flux Low | Proton | Unknown | 30.03.2024 14:52:54 | 30.03.2024 15:04:32 | 11 | HV | automatic log for run 1027
Comment: |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 0
HDMI2_clk = 1
HDMI3_clk = 0
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xB
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x00 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x3 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_AB]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_AB
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_AB]
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_AB_$12D$X
DISABLE_PRINT = 1
[Producer.tjmonopix2_CD]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_CD
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_CD]
EUDAQ_MN = monopix2_mon
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_CD_$12D$X
DISABLE_PRINT = 1
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
69
|
Sat Mar 30 20:27:35 2024 |
hh, mb, ps | High statistics | 1052 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Unknown | 30.03.2024 20:17:11 | 30.03.2024 20:30:02 | 12 | HV | automatic log for run 1052
Comment:
Back to stock veto period of 7us (100) |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 0
HDMI2_clk = 0
HDMI3_clk = 0
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xA
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x00 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x0 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_AB]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_AB
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_AB]
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_AB_$12D$X
DISABLE_PRINT = 1
[Producer.tjmonopix2_CD]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_CD
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_CD]
EUDAQ_MN = monopix2_mon
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_CD_$12D$X
DISABLE_PRINT = 1
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
9
|
Sat Mar 30 07:59:41 2024 |
bp, ci, hh | RD50-MPW4 | 1006 | RD50-MPW4 | 800 MeV | Low Flux Very Low | Proton | Good | 30.03.2024 07:46:50 | 30.03.2024 08:02:08 | 15 | Normal | automatic log for run 1006
Comment:
beautifully correlated  |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib_base.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_hitbus_dcols =
en_sfout_dcol = 0
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-9
inj_t0 = 511
matrix_config = matrix_mpw4.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 3
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
inj__u = 0
inj__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 0.92
th__i = 3
|
| Attachment 2: matrix_mpw4.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {masked} {en_inj} {en_hb} {en_sfout} {trimDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 0 0 0 0 13
00 01 0 0 0 0 4
00 02 0 0 0 0 9
00 03 0 0 0 0 12
00 04 0 0 0 0 7
00 05 0 0 0 0 10
00 06 0 0 0 0 8
00 07 0 0 0 0 8
00 08 0 0 0 0 8
00 09 0 0 0 0 9
00 10 0 0 0 0 10
00 11 0 0 0 0 5
00 12 0 0 0 0 14
00 13 0 0 0 0 6
00 14 0 0 0 0 7
00 15 0 0 0 0 3
00 16 0 0 0 0 5
00 17 0 0 0 0 15
00 18 0 0 0 0 12
00 19 0 0 0 0 11
00 20 0 0 0 0 6
00 21 0 0 0 0 5
00 22 0 0 0 0 7
00 23 0 0 0 0 6
00 24 0 0 0 0 10
00 25 0 0 0 0 4
00 26 0 0 0 0 6
00 27 0 0 0 0 0
00 28 0 0 0 0 6
00 29 0 0 0 0 6
00 30 0 0 0 0 11
00 31 0 0 0 0 3
00 32 0 0 0 0 6
00 33 0 0 0 0 8
00 34 0 0 0 0 9
00 35 0 0 0 0 8
00 36 0 0 0 0 11
00 37 0 0 0 0 8
00 38 0 0 0 0 11
00 39 0 0 0 0 8
00 40 0 0 0 0 13
00 41 0 0 0 0 8
00 42 0 0 0 0 7
00 43 0 0 0 0 5
00 44 0 0 0 0 10
00 45 0 0 0 0 14
00 46 0 0 0 0 3
00 47 0 0 0 0 8
00 48 0 0 0 0 7
00 49 0 0 0 0 7
00 50 0 0 0 0 5
00 51 0 0 0 0 8
00 52 0 0 0 0 11
00 53 0 0 0 0 7
00 54 0 0 0 0 8
00 55 0 0 0 0 10
00 56 0 0 0 0 11
00 57 0 0 0 0 6
00 58 0 0 0 0 11
00 59 0 0 0 0 4
00 60 0 0 0 0 8
00 61 0 0 0 0 5
00 62 1 0 0 0 10
00 63 0 0 0 0 9
01 00 0 0 0 0 15
01 01 0 0 0 0 10
01 02 0 0 0 0 8
01 03 0 0 0 0 7
01 04 0 0 0 0 10
01 05 0 0 0 0 0
01 06 0 0 0 0 10
01 07 0 0 0 0 15
01 08 0 0 0 0 4
01 09 0 0 0 0 13
01 10 0 0 0 0 9
01 11 0 0 0 0 4
01 12 0 0 0 0 12
01 13 0 0 0 0 11
01 14 0 0 0 0 7
01 15 0 0 0 0 2
01 16 0 0 0 0 7
01 17 0 0 0 0 12
01 18 0 0 0 0 6
01 19 0 0 0 0 10
01 20 0 0 0 0 9
01 21 0 0 0 0 13
01 22 0 0 0 0 6
01 23 0 0 0 0 12
01 24 0 0 0 0 5
01 25 0 0 0 0 10
01 26 0 0 0 0 9
01 27 0 0 0 0 9
01 28 0 0 0 0 5
01 29 0 0 0 0 4
01 30 0 0 0 0 9
01 31 0 0 0 0 6
01 32 0 0 0 0 10
01 33 0 0 0 0 5
01 34 1 0 0 0 15
01 35 0 0 0 0 8
01 36 0 0 0 0 4
01 37 0 0 0 0 7
01 38 0 0 0 0 12
01 39 0 0 0 0 8
01 40 0 0 0 0 9
01 41 0 0 0 0 4
01 42 0 0 0 0 12
01 43 0 0 0 0 6
01 44 0 0 0 0 6
01 45 0 0 0 0 13
01 46 0 0 0 0 12
01 47 0 0 0 0 8
01 48 0 0 0 0 4
01 49 0 0 0 0 10
01 50 0 0 0 0 10
01 51 0 0 0 0 8
01 52 0 0 0 0 10
01 53 0 0 0 0 11
01 54 0 0 0 0 11
01 55 0 0 0 0 4
01 56 0 0 0 0 13
01 57 0 0 0 0 12
01 58 0 0 0 0 4
01 59 0 0 0 0 5
01 60 0 0 0 0 9
01 61 0 0 0 0 7
01 62 0 0 0 0 7
01 63 0 0 0 0 10
02 00 0 0 0 0 6
02 01 0 0 0 0 11
02 02 0 0 0 0 14
02 03 0 0 0 0 8
02 04 0 0 0 0 11
02 05 0 0 0 0 14
02 06 0 0 0 0 11
02 07 0 0 0 0 12
02 08 0 0 0 0 7
02 09 0 0 0 0 10
02 10 0 0 0 0 6
02 11 0 0 0 0 7
02 12 0 0 0 0 9
02 13 0 0 0 0 5
02 14 0 0 0 0 8
02 15 0 0 0 0 6
02 16 0 0 0 0 10
02 17 0 0 0 0 10
02 18 0 0 0 0 10
02 19 0 0 0 0 8
02 20 0 0 0 0 9
02 21 0 0 0 0 7
02 22 0 0 0 0 4
02 23 0 0 0 0 7
02 24 0 0 0 0 12
02 25 0 0 0 0 2
02 26 0 0 0 0 2
02 27 0 0 0 0 9
02 28 0 0 0 0 7
02 29 0 0 0 0 8
02 30 0 0 0 0 9
02 31 0 0 0 0 11
02 32 0 0 0 0 7
02 33 0 0 0 0 9
02 34 0 0 0 0 6
02 35 1 0 0 0 10
02 36 0 0 0 0 10
02 37 0 0 0 0 14
02 38 0 0 0 0 7
02 39 0 0 0 0 7
02 40 0 0 0 0 7
02 41 0 0 0 0 9
02 42 0 0 0 0 6
02 43 0 0 0 0 9
02 44 0 0 0 0 4
02 45 0 0 0 0 10
02 46 0 0 0 0 12
02 47 0 0 0 0 8
02 48 0 0 0 0 5
02 49 0 0 0 0 12
02 50 0 0 0 0 5
02 51 0 0 0 0 9
02 52 0 0 0 0 6
02 53 0 0 0 0 5
02 54 0 0 0 0 6
02 55 0 0 0 0 8
02 56 0 0 0 0 4
02 57 0 0 0 0 7
02 58 0 0 0 0 15
02 59 0 0 0 0 15
02 60 0 0 0 0 8
02 61 0 0 0 0 9
02 62 0 0 0 0 12
02 63 0 0 0 0 8
03 00 0 0 0 0 8
03 01 0 0 0 0 11
03 02 0 0 0 0 5
03 03 0 0 0 0 2
03 04 0 0 0 0 6
03 05 0 0 0 0 9
03 06 0 0 0 0 6
03 07 0 0 0 0 7
03 08 0 0 0 0 8
03 09 0 0 0 0 8
03 10 0 0 0 0 6
03 11 0 0 0 0 5
03 12 0 0 0 0 12
03 13 0 0 0 0 3
03 14 0 0 0 0 9
03 15 0 0 0 0 1
03 16 0 0 0 0 6
03 17 0 0 0 0 13
03 18 0 0 0 0 15
03 19 0 0 0 0 8
03 20 0 0 0 0 8
03 21 0 0 0 0 6
03 22 0 0 0 0 7
03 23 0 0 0 0 8
03 24 0 0 0 0 4
03 25 0 0 0 0 5
03 26 0 0 0 0 6
03 27 0 0 0 0 5
03 28 0 0 0 0 11
03 29 0 0 0 0 9
03 30 0 0 0 0 6
03 31 0 0 0 0 12
03 32 0 0 0 0 6
03 33 0 0 0 0 6
03 34 0 0 0 0 9
03 35 0 0 0 0 6
03 36 0 0 0 0 10
03 37 0 0 0 0 11
03 38 0 0 0 0 10
03 39 0 0 0 0 10
03 40 0 0 0 0 4
03 41 0 0 0 0 8
03 42 0 0 0 0 12
03 43 0 0 0 0 12
03 44 0 0 0 0 9
03 45 0 0 0 0 12
03 46 0 0 0 0 9
03 47 0 0 0 0 3
03 48 0 0 0 0 9
03 49 0 0 0 0 7
03 50 0 0 0 0 1
03 51 0 0 0 0 8
03 52 0 0 0 0 9
03 53 0 0 0 0 10
03 54 0 0 0 0 4
03 55 0 0 0 0 3
03 56 0 0 0 0 12
03 57 0 0 0 0 5
03 58 0 0 0 0 4
03 59 0 0 0 0 7
03 60 1 0 0 0 8
03 61 0 0 0 0 8
03 62 0 0 0 0 8
03 63 0 0 0 0 1
04 00 0 0 0 0 8
04 01 0 0 0 0 15
04 02 0 0 0 0 12
04 03 0 0 0 0 4
04 04 0 0 0 0 9
04 05 0 0 0 0 11
04 06 0 0 0 0 14
04 07 0 0 0 0 10
04 08 0 0 0 0 4
04 09 0 0 0 0 7
04 10 0 0 0 0 8
04 11 0 0 0 0 11
04 12 0 0 0 0 9
04 13 0 0 0 0 11
04 14 0 0 0 0 7
04 15 0 0 0 0 10
04 16 0 0 0 0 3
04 17 0 0 0 0 10
04 18 0 0 0 0 11
04 19 0 0 0 0 12
04 20 0 0 0 0 10
04 21 0 0 0 0 11
04 22 0 0 0 0 8
04 23 0 0 0 0 11
04 24 0 0 0 0 2
04 25 0 0 0 0 3
04 26 0 0 0 0 9
04 27 0 0 0 0 11
04 28 0 0 0 0 7
04 29 0 0 0 0 4
04 30 0 0 0 0 5
04 31 0 0 0 0 9
04 32 0 0 0 0 4
04 33 0 0 0 0 8
04 34 0 0 0 0 7
04 35 0 0 0 0 3
04 36 0 0 0 0 4
04 37 0 0 0 0 10
... 3802 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x0 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/MPW4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
70
|
Sat Mar 30 20:46:41 2024 |
hh, mb, ps | High statistics | 1053 | TJ-Monopix2 | 800 MeV | Low Flux High | Proton | Unknown | 30.03.2024 20:31:14 | 30.03.2024 20:49:08 | 17 | HV | automatic log for run 1053
Comment:
Back to stock veto period of 7us (100)
Lets try with high |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 0
HDMI2_clk = 0
HDMI3_clk = 0
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xA
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x00 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x0 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_AB]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_AB
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_AB]
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_AB_$12D$X
DISABLE_PRINT = 1
[Producer.tjmonopix2_CD]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_CD
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_CD]
EUDAQ_MN = monopix2_mon
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_CD_$12D$X
DISABLE_PRINT = 1
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
32
|
Sat Mar 30 10:25:55 2024 |
bp, ci, hh | RD50-MPW4 | 1018 | RD50-MPW4 | 800 MeV | Low Flux Low | Proton | Crap | 30.03.2024 10:26:17 | 30.03.2024 10:28:21 | 2 | Normal | automatic log for run 1018
Comment: |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib_base.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_hitbus_dcols =
en_sfout_dcol = 0
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-9
inj_t0 = 511
matrix_config = matrix_mpw4.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 3
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
inj__u = 0
inj__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 0.92
th__i = 3
|
| Attachment 2: matrix_mpw4.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {masked} {en_inj} {en_hb} {en_sfout} {trimDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 0 0 0 0 13
00 01 0 0 0 0 4
00 02 0 0 0 0 9
00 03 0 0 0 0 12
00 04 0 0 0 0 7
00 05 0 0 0 0 10
00 06 0 0 0 0 8
00 07 0 0 0 0 8
00 08 0 0 0 0 8
00 09 0 0 0 0 9
00 10 0 0 0 0 10
00 11 0 0 0 0 5
00 12 0 0 0 0 14
00 13 0 0 0 0 6
00 14 0 0 0 0 7
00 15 0 0 0 0 3
00 16 0 0 0 0 5
00 17 0 0 0 0 15
00 18 0 0 0 0 12
00 19 0 0 0 0 11
00 20 0 0 0 0 6
00 21 0 0 0 0 5
00 22 0 0 0 0 7
00 23 0 0 0 0 6
00 24 0 0 0 0 10
00 25 0 0 0 0 4
00 26 0 0 0 0 6
00 27 0 0 0 0 0
00 28 0 0 0 0 6
00 29 0 0 0 0 6
00 30 0 0 0 0 11
00 31 0 0 0 0 3
00 32 0 0 0 0 6
00 33 0 0 0 0 8
00 34 0 0 0 0 9
00 35 0 0 0 0 8
00 36 0 0 0 0 11
00 37 0 0 0 0 8
00 38 0 0 0 0 11
00 39 0 0 0 0 8
00 40 0 0 0 0 13
00 41 0 0 0 0 8
00 42 0 0 0 0 7
00 43 0 0 0 0 5
00 44 0 0 0 0 10
00 45 0 0 0 0 14
00 46 0 0 0 0 3
00 47 0 0 0 0 8
00 48 0 0 0 0 7
00 49 0 0 0 0 7
00 50 0 0 0 0 5
00 51 0 0 0 0 8
00 52 0 0 0 0 11
00 53 0 0 0 0 7
00 54 0 0 0 0 8
00 55 0 0 0 0 10
00 56 0 0 0 0 11
00 57 0 0 0 0 6
00 58 0 0 0 0 11
00 59 0 0 0 0 4
00 60 0 0 0 0 8
00 61 0 0 0 0 5
00 62 1 0 0 0 10
00 63 0 0 0 0 9
01 00 0 0 0 0 15
01 01 0 0 0 0 10
01 02 0 0 0 0 8
01 03 0 0 0 0 7
01 04 0 0 0 0 10
01 05 0 0 0 0 0
01 06 0 0 0 0 10
01 07 0 0 0 0 15
01 08 0 0 0 0 4
01 09 0 0 0 0 13
01 10 0 0 0 0 9
01 11 0 0 0 0 4
01 12 0 0 0 0 12
01 13 0 0 0 0 11
01 14 0 0 0 0 7
01 15 0 0 0 0 2
01 16 0 0 0 0 7
01 17 0 0 0 0 12
01 18 0 0 0 0 6
01 19 0 0 0 0 10
01 20 0 0 0 0 9
01 21 0 0 0 0 13
01 22 0 0 0 0 6
01 23 0 0 0 0 12
01 24 0 0 0 0 5
01 25 0 0 0 0 10
01 26 0 0 0 0 9
01 27 0 0 0 0 9
01 28 0 0 0 0 5
01 29 0 0 0 0 4
01 30 0 0 0 0 9
01 31 0 0 0 0 6
01 32 0 0 0 0 10
01 33 0 0 0 0 5
01 34 1 0 0 0 15
01 35 0 0 0 0 8
01 36 0 0 0 0 4
01 37 0 0 0 0 7
01 38 0 0 0 0 12
01 39 0 0 0 0 8
01 40 0 0 0 0 9
01 41 0 0 0 0 4
01 42 0 0 0 0 12
01 43 0 0 0 0 6
01 44 0 0 0 0 6
01 45 0 0 0 0 13
01 46 0 0 0 0 12
01 47 0 0 0 0 8
01 48 0 0 0 0 4
01 49 0 0 0 0 10
01 50 0 0 0 0 10
01 51 0 0 0 0 8
01 52 0 0 0 0 10
01 53 0 0 0 0 11
01 54 0 0 0 0 11
01 55 0 0 0 0 4
01 56 0 0 0 0 13
01 57 0 0 0 0 12
01 58 0 0 0 0 4
01 59 0 0 0 0 5
01 60 0 0 0 0 9
01 61 0 0 0 0 7
01 62 0 0 0 0 7
01 63 0 0 0 0 10
02 00 0 0 0 0 6
02 01 0 0 0 0 11
02 02 0 0 0 0 14
02 03 0 0 0 0 8
02 04 0 0 0 0 11
02 05 0 0 0 0 14
02 06 0 0 0 0 11
02 07 0 0 0 0 12
02 08 0 0 0 0 7
02 09 0 0 0 0 10
02 10 0 0 0 0 6
02 11 0 0 0 0 7
02 12 0 0 0 0 9
02 13 0 0 0 0 5
02 14 0 0 0 0 8
02 15 0 0 0 0 6
02 16 0 0 0 0 10
02 17 0 0 0 0 10
02 18 0 0 0 0 10
02 19 0 0 0 0 8
02 20 0 0 0 0 9
02 21 0 0 0 0 7
02 22 0 0 0 0 4
02 23 0 0 0 0 7
02 24 0 0 0 0 12
02 25 0 0 0 0 2
02 26 0 0 0 0 2
02 27 0 0 0 0 9
02 28 0 0 0 0 7
02 29 0 0 0 0 8
02 30 0 0 0 0 9
02 31 0 0 0 0 11
02 32 0 0 0 0 7
02 33 0 0 0 0 9
02 34 0 0 0 0 6
02 35 1 0 0 0 10
02 36 0 0 0 0 10
02 37 0 0 0 0 14
02 38 0 0 0 0 7
02 39 0 0 0 0 7
02 40 0 0 0 0 7
02 41 0 0 0 0 9
02 42 0 0 0 0 6
02 43 0 0 0 0 9
02 44 0 0 0 0 4
02 45 0 0 0 0 10
02 46 0 0 0 0 12
02 47 0 0 0 0 8
02 48 0 0 0 0 5
02 49 0 0 0 0 12
02 50 0 0 0 0 5
02 51 0 0 0 0 9
02 52 0 0 0 0 6
02 53 0 0 0 0 5
02 54 0 0 0 0 6
02 55 0 0 0 0 8
02 56 0 0 0 0 4
02 57 0 0 0 0 7
02 58 0 0 0 0 15
02 59 0 0 0 0 15
02 60 0 0 0 0 8
02 61 0 0 0 0 9
02 62 0 0 0 0 12
02 63 0 0 0 0 8
03 00 0 0 0 0 8
03 01 0 0 0 0 11
03 02 0 0 0 0 5
03 03 0 0 0 0 2
03 04 0 0 0 0 6
03 05 0 0 0 0 9
03 06 0 0 0 0 6
03 07 0 0 0 0 7
03 08 0 0 0 0 8
03 09 0 0 0 0 8
03 10 0 0 0 0 6
03 11 0 0 0 0 5
03 12 0 0 0 0 12
03 13 0 0 0 0 3
03 14 0 0 0 0 9
03 15 0 0 0 0 1
03 16 0 0 0 0 6
03 17 0 0 0 0 13
03 18 0 0 0 0 15
03 19 0 0 0 0 8
03 20 0 0 0 0 8
03 21 0 0 0 0 6
03 22 0 0 0 0 7
03 23 0 0 0 0 8
03 24 0 0 0 0 4
03 25 0 0 0 0 5
03 26 0 0 0 0 6
03 27 0 0 0 0 5
03 28 0 0 0 0 11
03 29 0 0 0 0 9
03 30 0 0 0 0 6
03 31 0 0 0 0 12
03 32 0 0 0 0 6
03 33 0 0 0 0 6
03 34 0 0 0 0 9
03 35 0 0 0 0 6
03 36 0 0 0 0 10
03 37 0 0 0 0 11
03 38 0 0 0 0 10
03 39 0 0 0 0 10
03 40 0 0 0 0 4
03 41 0 0 0 0 8
03 42 0 0 0 0 12
03 43 0 0 0 0 12
03 44 0 0 0 0 9
03 45 0 0 0 0 12
03 46 0 0 0 0 9
03 47 0 0 0 0 3
03 48 0 0 0 0 9
03 49 0 0 0 0 7
03 50 0 0 0 0 1
03 51 0 0 0 0 8
03 52 0 0 0 0 9
03 53 0 0 0 0 10
03 54 0 0 0 0 4
03 55 0 0 0 0 3
03 56 0 0 0 0 12
03 57 0 0 0 0 5
03 58 0 0 0 0 4
03 59 0 0 0 0 7
03 60 1 0 0 0 8
03 61 0 0 0 0 8
03 62 0 0 0 0 8
03 63 0 0 0 0 1
04 00 0 0 0 0 8
04 01 0 0 0 0 15
04 02 0 0 0 0 12
04 03 0 0 0 0 4
04 04 0 0 0 0 9
04 05 0 0 0 0 11
04 06 0 0 0 0 14
04 07 0 0 0 0 10
04 08 0 0 0 0 4
04 09 0 0 0 0 7
04 10 0 0 0 0 8
04 11 0 0 0 0 11
04 12 0 0 0 0 9
04 13 0 0 0 0 11
04 14 0 0 0 0 7
04 15 0 0 0 0 10
04 16 0 0 0 0 3
04 17 0 0 0 0 10
04 18 0 0 0 0 11
04 19 0 0 0 0 12
04 20 0 0 0 0 10
04 21 0 0 0 0 11
04 22 0 0 0 0 8
04 23 0 0 0 0 11
04 24 0 0 0 0 2
04 25 0 0 0 0 3
04 26 0 0 0 0 9
04 27 0 0 0 0 11
04 28 0 0 0 0 7
04 29 0 0 0 0 4
04 30 0 0 0 0 5
04 31 0 0 0 0 9
04 32 0 0 0 0 4
04 33 0 0 0 0 8
04 34 0 0 0 0 7
04 35 0 0 0 0 3
04 36 0 0 0 0 4
04 37 0 0 0 0 10
... 3802 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x0 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/MPW4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
46
|
Sat Mar 30 15:08:33 2024 |
hh, mb, ps | 1st tests | 1029 | TJ-Monopix2 | 800 MeV | Low Flux Low | Proton | Unknown | 30.03.2024 15:08:26 | 30.03.2024 15:11:00 | 2 | HV | automatic log for run 1029
Comment: |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 0
HDMI2_clk = 1
HDMI3_clk = 0
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xB
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x00 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x3 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_AB]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_AB
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_AB]
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_AB_$12D$X
DISABLE_PRINT = 1
[Producer.tjmonopix2_CD]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_CD
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_CD]
EUDAQ_MN = monopix2_mon
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_CD_$12D$X
DISABLE_PRINT = 1
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
47
|
Sat Mar 30 15:18:29 2024 |
hh, mb, ps | 1st tests | 1030 | TJ-Monopix2 | 800 MeV | Low Flux Low | Proton | Unknown | 30.03.2024 15:18:21 | 30.03.2024 15:20:55 | 2 | HV | automatic log for run 1030
Comment: |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 0
HDMI2_clk = 1
HDMI3_clk = 0
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xB
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x00 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x3 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_AB]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_AB
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_AB]
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_AB_$12D$X
DISABLE_PRINT = 1
[Producer.tjmonopix2_CD]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_CD
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_CD]
EUDAQ_MN = monopix2_mon
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_CD_$12D$X
DISABLE_PRINT = 1
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
50
|
Sat Mar 30 15:24:44 2024 |
hh, mb, ps | 1st tests | 1033 | TJ-Monopix2 | 800 MeV | Low Flux Low | Proton | Unknown | 30.03.2024 15:25:06 | 30.03.2024 15:27:10 | 2 | HV | automatic log for run 1033
Comment: |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 0
HDMI2_clk = 1
HDMI3_clk = 0
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xC
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x00 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x3 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_AB]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_AB
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_AB]
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_AB_$12D$X
DISABLE_PRINT = 1
[Producer.tjmonopix2_CD]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_CD
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_CD]
EUDAQ_MN = monopix2_mon
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_CD_$12D$X
DISABLE_PRINT = 1
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
55
|
Sat Mar 30 16:03:35 2024 |
hh, mb, ps | 1st tests | 1038 | TJ-Monopix2 | 800 MeV | Low Flux Low | Proton | Unknown | 30.03.2024 16:03:18 | 30.03.2024 16:06:01 | 2 | HV | automatic log for run 1038
Comment: |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 0
HDMI2_clk = 1
HDMI3_clk = 0
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xC
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x00 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x7 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_AB]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_AB
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_AB]
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_AB_$12D$X
DISABLE_PRINT = 1
[Producer.tjmonopix2_CD]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_CD
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_CD]
EUDAQ_MN = monopix2_mon
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_CD_$12D$X
DISABLE_PRINT = 1
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
57
|
Sat Mar 30 16:15:20 2024 |
hh, mb, ps | 1st tests | 1040 | TJ-Monopix2 | 800 MeV | Low Flux Low | Proton | Unknown | 30.03.2024 16:15:22 | 30.03.2024 16:17:46 | 2 | HV | automatic log for run 1040
Comment: |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 0
HDMI2_clk = 1
HDMI3_clk = 0
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 10 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xC
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x00 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x3 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_AB]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_AB
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_AB]
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_AB_$12D$X
DISABLE_PRINT = 1
[Producer.tjmonopix2_CD]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_CD
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_CD]
EUDAQ_MN = monopix2_mon
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_CD_$12D$X
DISABLE_PRINT = 1
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
8
|
Sat Mar 30 07:44:15 2024 |
bp, ci, hh | RD50-MPW4 | 1005 | RD50-MPW4 | 800 MeV | Low Flux Very Low | Proton | Unknown | 30.03.2024 07:25:51 | 30.03.2024 07:46:41 | 20 | Normal | automatic log for run 1005
Comment:
beautifully correlated |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib_base.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_hitbus_dcols =
en_sfout_dcol = 0
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-9
inj_t0 = 511
matrix_config = matrix_mpw4.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 3
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
inj__u = 0
inj__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 0.92
th__i = 3
|
| Attachment 2: matrix_mpw4.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {masked} {en_inj} {en_hb} {en_sfout} {trimDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 0 0 0 0 13
00 01 0 0 0 0 4
00 02 0 0 0 0 9
00 03 0 0 0 0 12
00 04 0 0 0 0 7
00 05 0 0 0 0 10
00 06 0 0 0 0 8
00 07 0 0 0 0 8
00 08 0 0 0 0 8
00 09 0 0 0 0 9
00 10 0 0 0 0 10
00 11 0 0 0 0 5
00 12 0 0 0 0 14
00 13 0 0 0 0 6
00 14 0 0 0 0 7
00 15 0 0 0 0 3
00 16 0 0 0 0 5
00 17 0 0 0 0 15
00 18 0 0 0 0 12
00 19 0 0 0 0 11
00 20 0 0 0 0 6
00 21 0 0 0 0 5
00 22 0 0 0 0 7
00 23 0 0 0 0 6
00 24 0 0 0 0 10
00 25 0 0 0 0 4
00 26 0 0 0 0 6
00 27 0 0 0 0 0
00 28 0 0 0 0 6
00 29 0 0 0 0 6
00 30 0 0 0 0 11
00 31 0 0 0 0 3
00 32 0 0 0 0 6
00 33 0 0 0 0 8
00 34 0 0 0 0 9
00 35 0 0 0 0 8
00 36 0 0 0 0 11
00 37 0 0 0 0 8
00 38 0 0 0 0 11
00 39 0 0 0 0 8
00 40 0 0 0 0 13
00 41 0 0 0 0 8
00 42 0 0 0 0 7
00 43 0 0 0 0 5
00 44 0 0 0 0 10
00 45 0 0 0 0 14
00 46 0 0 0 0 3
00 47 0 0 0 0 8
00 48 0 0 0 0 7
00 49 0 0 0 0 7
00 50 0 0 0 0 5
00 51 0 0 0 0 8
00 52 0 0 0 0 11
00 53 0 0 0 0 7
00 54 0 0 0 0 8
00 55 0 0 0 0 10
00 56 0 0 0 0 11
00 57 0 0 0 0 6
00 58 0 0 0 0 11
00 59 0 0 0 0 4
00 60 0 0 0 0 8
00 61 0 0 0 0 5
00 62 1 0 0 0 10
00 63 0 0 0 0 9
01 00 0 0 0 0 15
01 01 0 0 0 0 10
01 02 0 0 0 0 8
01 03 0 0 0 0 7
01 04 0 0 0 0 10
01 05 0 0 0 0 0
01 06 0 0 0 0 10
01 07 0 0 0 0 15
01 08 0 0 0 0 4
01 09 0 0 0 0 13
01 10 0 0 0 0 9
01 11 0 0 0 0 4
01 12 0 0 0 0 12
01 13 0 0 0 0 11
01 14 0 0 0 0 7
01 15 0 0 0 0 2
01 16 0 0 0 0 7
01 17 0 0 0 0 12
01 18 0 0 0 0 6
01 19 0 0 0 0 10
01 20 0 0 0 0 9
01 21 0 0 0 0 13
01 22 0 0 0 0 6
01 23 0 0 0 0 12
01 24 0 0 0 0 5
01 25 0 0 0 0 10
01 26 0 0 0 0 9
01 27 0 0 0 0 9
01 28 0 0 0 0 5
01 29 0 0 0 0 4
01 30 0 0 0 0 9
01 31 0 0 0 0 6
01 32 0 0 0 0 10
01 33 0 0 0 0 5
01 34 1 0 0 0 15
01 35 0 0 0 0 8
01 36 0 0 0 0 4
01 37 0 0 0 0 7
01 38 0 0 0 0 12
01 39 0 0 0 0 8
01 40 0 0 0 0 9
01 41 0 0 0 0 4
01 42 0 0 0 0 12
01 43 0 0 0 0 6
01 44 0 0 0 0 6
01 45 0 0 0 0 13
01 46 0 0 0 0 12
01 47 0 0 0 0 8
01 48 0 0 0 0 4
01 49 0 0 0 0 10
01 50 0 0 0 0 10
01 51 0 0 0 0 8
01 52 0 0 0 0 10
01 53 0 0 0 0 11
01 54 0 0 0 0 11
01 55 0 0 0 0 4
01 56 0 0 0 0 13
01 57 0 0 0 0 12
01 58 0 0 0 0 4
01 59 0 0 0 0 5
01 60 0 0 0 0 9
01 61 0 0 0 0 7
01 62 0 0 0 0 7
01 63 0 0 0 0 10
02 00 0 0 0 0 6
02 01 0 0 0 0 11
02 02 0 0 0 0 14
02 03 0 0 0 0 8
02 04 0 0 0 0 11
02 05 0 0 0 0 14
02 06 0 0 0 0 11
02 07 0 0 0 0 12
02 08 0 0 0 0 7
02 09 0 0 0 0 10
02 10 0 0 0 0 6
02 11 0 0 0 0 7
02 12 0 0 0 0 9
02 13 0 0 0 0 5
02 14 0 0 0 0 8
02 15 0 0 0 0 6
02 16 0 0 0 0 10
02 17 0 0 0 0 10
02 18 0 0 0 0 10
02 19 0 0 0 0 8
02 20 0 0 0 0 9
02 21 0 0 0 0 7
02 22 0 0 0 0 4
02 23 0 0 0 0 7
02 24 0 0 0 0 12
02 25 0 0 0 0 2
02 26 0 0 0 0 2
02 27 0 0 0 0 9
02 28 0 0 0 0 7
02 29 0 0 0 0 8
02 30 0 0 0 0 9
02 31 0 0 0 0 11
02 32 0 0 0 0 7
02 33 0 0 0 0 9
02 34 0 0 0 0 6
02 35 1 0 0 0 10
02 36 0 0 0 0 10
02 37 0 0 0 0 14
02 38 0 0 0 0 7
02 39 0 0 0 0 7
02 40 0 0 0 0 7
02 41 0 0 0 0 9
02 42 0 0 0 0 6
02 43 0 0 0 0 9
02 44 0 0 0 0 4
02 45 0 0 0 0 10
02 46 0 0 0 0 12
02 47 0 0 0 0 8
02 48 0 0 0 0 5
02 49 0 0 0 0 12
02 50 0 0 0 0 5
02 51 0 0 0 0 9
02 52 0 0 0 0 6
02 53 0 0 0 0 5
02 54 0 0 0 0 6
02 55 0 0 0 0 8
02 56 0 0 0 0 4
02 57 0 0 0 0 7
02 58 0 0 0 0 15
02 59 0 0 0 0 15
02 60 0 0 0 0 8
02 61 0 0 0 0 9
02 62 0 0 0 0 12
02 63 0 0 0 0 8
03 00 0 0 0 0 8
03 01 0 0 0 0 11
03 02 0 0 0 0 5
03 03 0 0 0 0 2
03 04 0 0 0 0 6
03 05 0 0 0 0 9
03 06 0 0 0 0 6
03 07 0 0 0 0 7
03 08 0 0 0 0 8
03 09 0 0 0 0 8
03 10 0 0 0 0 6
03 11 0 0 0 0 5
03 12 0 0 0 0 12
03 13 0 0 0 0 3
03 14 0 0 0 0 9
03 15 0 0 0 0 1
03 16 0 0 0 0 6
03 17 0 0 0 0 13
03 18 0 0 0 0 15
03 19 0 0 0 0 8
03 20 0 0 0 0 8
03 21 0 0 0 0 6
03 22 0 0 0 0 7
03 23 0 0 0 0 8
03 24 0 0 0 0 4
03 25 0 0 0 0 5
03 26 0 0 0 0 6
03 27 0 0 0 0 5
03 28 0 0 0 0 11
03 29 0 0 0 0 9
03 30 0 0 0 0 6
03 31 0 0 0 0 12
03 32 0 0 0 0 6
03 33 0 0 0 0 6
03 34 0 0 0 0 9
03 35 0 0 0 0 6
03 36 0 0 0 0 10
03 37 0 0 0 0 11
03 38 0 0 0 0 10
03 39 0 0 0 0 10
03 40 0 0 0 0 4
03 41 0 0 0 0 8
03 42 0 0 0 0 12
03 43 0 0 0 0 12
03 44 0 0 0 0 9
03 45 0 0 0 0 12
03 46 0 0 0 0 9
03 47 0 0 0 0 3
03 48 0 0 0 0 9
03 49 0 0 0 0 7
03 50 0 0 0 0 1
03 51 0 0 0 0 8
03 52 0 0 0 0 9
03 53 0 0 0 0 10
03 54 0 0 0 0 4
03 55 0 0 0 0 3
03 56 0 0 0 0 12
03 57 0 0 0 0 5
03 58 0 0 0 0 4
03 59 0 0 0 0 7
03 60 1 0 0 0 8
03 61 0 0 0 0 8
03 62 0 0 0 0 8
03 63 0 0 0 0 1
04 00 0 0 0 0 8
04 01 0 0 0 0 15
04 02 0 0 0 0 12
04 03 0 0 0 0 4
04 04 0 0 0 0 9
04 05 0 0 0 0 11
04 06 0 0 0 0 14
04 07 0 0 0 0 10
04 08 0 0 0 0 4
04 09 0 0 0 0 7
04 10 0 0 0 0 8
04 11 0 0 0 0 11
04 12 0 0 0 0 9
04 13 0 0 0 0 11
04 14 0 0 0 0 7
04 15 0 0 0 0 10
04 16 0 0 0 0 3
04 17 0 0 0 0 10
04 18 0 0 0 0 11
04 19 0 0 0 0 12
04 20 0 0 0 0 10
04 21 0 0 0 0 11
04 22 0 0 0 0 8
04 23 0 0 0 0 11
04 24 0 0 0 0 2
04 25 0 0 0 0 3
04 26 0 0 0 0 9
04 27 0 0 0 0 11
04 28 0 0 0 0 7
04 29 0 0 0 0 4
04 30 0 0 0 0 5
04 31 0 0 0 0 9
04 32 0 0 0 0 4
04 33 0 0 0 0 8
04 34 0 0 0 0 7
04 35 0 0 0 0 3
04 36 0 0 0 0 4
04 37 0 0 0 0 10
... 3802 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x0 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/MPW4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
12
|
Sat Mar 30 08:21:04 2024 |
bp, ci, hh | RD50-MPW4 | 1007 | RD50-MPW4 | 800 MeV | Low Flux Very Low | Proton | Good | 30.03.2024 08:02:46 | 30.03.2024 08:23:30 | 20 | Normal | automatic log for run 1007
Comment:
waiting for eam |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib_base.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_hitbus_dcols =
en_sfout_dcol = 0
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-9
inj_t0 = 511
matrix_config = matrix_mpw4.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 3
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
inj__u = 0
inj__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 0.92
th__i = 3
|
| Attachment 2: matrix_mpw4.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {masked} {en_inj} {en_hb} {en_sfout} {trimDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 0 0 0 0 13
00 01 0 0 0 0 4
00 02 0 0 0 0 9
00 03 0 0 0 0 12
00 04 0 0 0 0 7
00 05 0 0 0 0 10
00 06 0 0 0 0 8
00 07 0 0 0 0 8
00 08 0 0 0 0 8
00 09 0 0 0 0 9
00 10 0 0 0 0 10
00 11 0 0 0 0 5
00 12 0 0 0 0 14
00 13 0 0 0 0 6
00 14 0 0 0 0 7
00 15 0 0 0 0 3
00 16 0 0 0 0 5
00 17 0 0 0 0 15
00 18 0 0 0 0 12
00 19 0 0 0 0 11
00 20 0 0 0 0 6
00 21 0 0 0 0 5
00 22 0 0 0 0 7
00 23 0 0 0 0 6
00 24 0 0 0 0 10
00 25 0 0 0 0 4
00 26 0 0 0 0 6
00 27 0 0 0 0 0
00 28 0 0 0 0 6
00 29 0 0 0 0 6
00 30 0 0 0 0 11
00 31 0 0 0 0 3
00 32 0 0 0 0 6
00 33 0 0 0 0 8
00 34 0 0 0 0 9
00 35 0 0 0 0 8
00 36 0 0 0 0 11
00 37 0 0 0 0 8
00 38 0 0 0 0 11
00 39 0 0 0 0 8
00 40 0 0 0 0 13
00 41 0 0 0 0 8
00 42 0 0 0 0 7
00 43 0 0 0 0 5
00 44 0 0 0 0 10
00 45 0 0 0 0 14
00 46 0 0 0 0 3
00 47 0 0 0 0 8
00 48 0 0 0 0 7
00 49 0 0 0 0 7
00 50 0 0 0 0 5
00 51 0 0 0 0 8
00 52 0 0 0 0 11
00 53 0 0 0 0 7
00 54 0 0 0 0 8
00 55 0 0 0 0 10
00 56 0 0 0 0 11
00 57 0 0 0 0 6
00 58 0 0 0 0 11
00 59 0 0 0 0 4
00 60 0 0 0 0 8
00 61 0 0 0 0 5
00 62 1 0 0 0 10
00 63 0 0 0 0 9
01 00 0 0 0 0 15
01 01 0 0 0 0 10
01 02 0 0 0 0 8
01 03 0 0 0 0 7
01 04 0 0 0 0 10
01 05 0 0 0 0 0
01 06 0 0 0 0 10
01 07 0 0 0 0 15
01 08 0 0 0 0 4
01 09 0 0 0 0 13
01 10 0 0 0 0 9
01 11 0 0 0 0 4
01 12 0 0 0 0 12
01 13 0 0 0 0 11
01 14 0 0 0 0 7
01 15 0 0 0 0 2
01 16 0 0 0 0 7
01 17 0 0 0 0 12
01 18 0 0 0 0 6
01 19 0 0 0 0 10
01 20 0 0 0 0 9
01 21 0 0 0 0 13
01 22 0 0 0 0 6
01 23 0 0 0 0 12
01 24 0 0 0 0 5
01 25 0 0 0 0 10
01 26 0 0 0 0 9
01 27 0 0 0 0 9
01 28 0 0 0 0 5
01 29 0 0 0 0 4
01 30 0 0 0 0 9
01 31 0 0 0 0 6
01 32 0 0 0 0 10
01 33 0 0 0 0 5
01 34 1 0 0 0 15
01 35 0 0 0 0 8
01 36 0 0 0 0 4
01 37 0 0 0 0 7
01 38 0 0 0 0 12
01 39 0 0 0 0 8
01 40 0 0 0 0 9
01 41 0 0 0 0 4
01 42 0 0 0 0 12
01 43 0 0 0 0 6
01 44 0 0 0 0 6
01 45 0 0 0 0 13
01 46 0 0 0 0 12
01 47 0 0 0 0 8
01 48 0 0 0 0 4
01 49 0 0 0 0 10
01 50 0 0 0 0 10
01 51 0 0 0 0 8
01 52 0 0 0 0 10
01 53 0 0 0 0 11
01 54 0 0 0 0 11
01 55 0 0 0 0 4
01 56 0 0 0 0 13
01 57 0 0 0 0 12
01 58 0 0 0 0 4
01 59 0 0 0 0 5
01 60 0 0 0 0 9
01 61 0 0 0 0 7
01 62 0 0 0 0 7
01 63 0 0 0 0 10
02 00 0 0 0 0 6
02 01 0 0 0 0 11
02 02 0 0 0 0 14
02 03 0 0 0 0 8
02 04 0 0 0 0 11
02 05 0 0 0 0 14
02 06 0 0 0 0 11
02 07 0 0 0 0 12
02 08 0 0 0 0 7
02 09 0 0 0 0 10
02 10 0 0 0 0 6
02 11 0 0 0 0 7
02 12 0 0 0 0 9
02 13 0 0 0 0 5
02 14 0 0 0 0 8
02 15 0 0 0 0 6
02 16 0 0 0 0 10
02 17 0 0 0 0 10
02 18 0 0 0 0 10
02 19 0 0 0 0 8
02 20 0 0 0 0 9
02 21 0 0 0 0 7
02 22 0 0 0 0 4
02 23 0 0 0 0 7
02 24 0 0 0 0 12
02 25 0 0 0 0 2
02 26 0 0 0 0 2
02 27 0 0 0 0 9
02 28 0 0 0 0 7
02 29 0 0 0 0 8
02 30 0 0 0 0 9
02 31 0 0 0 0 11
02 32 0 0 0 0 7
02 33 0 0 0 0 9
02 34 0 0 0 0 6
02 35 1 0 0 0 10
02 36 0 0 0 0 10
02 37 0 0 0 0 14
02 38 0 0 0 0 7
02 39 0 0 0 0 7
02 40 0 0 0 0 7
02 41 0 0 0 0 9
02 42 0 0 0 0 6
02 43 0 0 0 0 9
02 44 0 0 0 0 4
02 45 0 0 0 0 10
02 46 0 0 0 0 12
02 47 0 0 0 0 8
02 48 0 0 0 0 5
02 49 0 0 0 0 12
02 50 0 0 0 0 5
02 51 0 0 0 0 9
02 52 0 0 0 0 6
02 53 0 0 0 0 5
02 54 0 0 0 0 6
02 55 0 0 0 0 8
02 56 0 0 0 0 4
02 57 0 0 0 0 7
02 58 0 0 0 0 15
02 59 0 0 0 0 15
02 60 0 0 0 0 8
02 61 0 0 0 0 9
02 62 0 0 0 0 12
02 63 0 0 0 0 8
03 00 0 0 0 0 8
03 01 0 0 0 0 11
03 02 0 0 0 0 5
03 03 0 0 0 0 2
03 04 0 0 0 0 6
03 05 0 0 0 0 9
03 06 0 0 0 0 6
03 07 0 0 0 0 7
03 08 0 0 0 0 8
03 09 0 0 0 0 8
03 10 0 0 0 0 6
03 11 0 0 0 0 5
03 12 0 0 0 0 12
03 13 0 0 0 0 3
03 14 0 0 0 0 9
03 15 0 0 0 0 1
03 16 0 0 0 0 6
03 17 0 0 0 0 13
03 18 0 0 0 0 15
03 19 0 0 0 0 8
03 20 0 0 0 0 8
03 21 0 0 0 0 6
03 22 0 0 0 0 7
03 23 0 0 0 0 8
03 24 0 0 0 0 4
03 25 0 0 0 0 5
03 26 0 0 0 0 6
03 27 0 0 0 0 5
03 28 0 0 0 0 11
03 29 0 0 0 0 9
03 30 0 0 0 0 6
03 31 0 0 0 0 12
03 32 0 0 0 0 6
03 33 0 0 0 0 6
03 34 0 0 0 0 9
03 35 0 0 0 0 6
03 36 0 0 0 0 10
03 37 0 0 0 0 11
03 38 0 0 0 0 10
03 39 0 0 0 0 10
03 40 0 0 0 0 4
03 41 0 0 0 0 8
03 42 0 0 0 0 12
03 43 0 0 0 0 12
03 44 0 0 0 0 9
03 45 0 0 0 0 12
03 46 0 0 0 0 9
03 47 0 0 0 0 3
03 48 0 0 0 0 9
03 49 0 0 0 0 7
03 50 0 0 0 0 1
03 51 0 0 0 0 8
03 52 0 0 0 0 9
03 53 0 0 0 0 10
03 54 0 0 0 0 4
03 55 0 0 0 0 3
03 56 0 0 0 0 12
03 57 0 0 0 0 5
03 58 0 0 0 0 4
03 59 0 0 0 0 7
03 60 1 0 0 0 8
03 61 0 0 0 0 8
03 62 0 0 0 0 8
03 63 0 0 0 0 1
04 00 0 0 0 0 8
04 01 0 0 0 0 15
04 02 0 0 0 0 12
04 03 0 0 0 0 4
04 04 0 0 0 0 9
04 05 0 0 0 0 11
04 06 0 0 0 0 14
04 07 0 0 0 0 10
04 08 0 0 0 0 4
04 09 0 0 0 0 7
04 10 0 0 0 0 8
04 11 0 0 0 0 11
04 12 0 0 0 0 9
04 13 0 0 0 0 11
04 14 0 0 0 0 7
04 15 0 0 0 0 10
04 16 0 0 0 0 3
04 17 0 0 0 0 10
04 18 0 0 0 0 11
04 19 0 0 0 0 12
04 20 0 0 0 0 10
04 21 0 0 0 0 11
04 22 0 0 0 0 8
04 23 0 0 0 0 11
04 24 0 0 0 0 2
04 25 0 0 0 0 3
04 26 0 0 0 0 9
04 27 0 0 0 0 11
04 28 0 0 0 0 7
04 29 0 0 0 0 4
04 30 0 0 0 0 5
04 31 0 0 0 0 9
04 32 0 0 0 0 4
04 33 0 0 0 0 8
04 34 0 0 0 0 7
04 35 0 0 0 0 3
04 36 0 0 0 0 4
04 37 0 0 0 0 10
... 3802 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x0 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/MPW4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
63
|
Sat Mar 30 17:31:59 2024 |
hh, mb, ps | High statistics | 1046 | TJ-Monopix2 | 800 MeV | Low Flux Low | Proton | Unknown | 30.03.2024 17:13:09 | 30.03.2024 17:34:25 | 21 | HV | automatic log for run 1046
Comment:
High statistics run, from now we fix the geometry
Veto: 7us (100, so 7 us is handshake time) |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 0
HDMI2_clk = 0
HDMI3_clk = 0
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xA
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x00 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x0 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/Data/2024_03_MAUS/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_AB]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_AB
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_AB]
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_AB_$12D$X
DISABLE_PRINT = 1
[Producer.tjmonopix2_CD]
# connection to the data collector
EUDAQ_DC = dc_tjmonopix2_CD
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
[DataCollector.dc_tjmonopix2_CD]
EUDAQ_MN = monopix2_mon
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/raw/run$3R_tjmonopix2_CD_$12D$X
DISABLE_PRINT = 1
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
| Attachment 2: testbench_AB.yaml
|
general: # General configuration
readout_system: # Readout system, available platforms are BDAQ53 or MIO3 (+ GPAC). BDAQ53 is default
output_directory: /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/h5 #'/media/raid/data/tjmonopix2/2021-10-25_elsa/tuning' # Top-level output data directory, default is the current folder where the script is started
# Connected Modules
modules:
module_0: # Arbitrary name of module, defines folder name with chip sub folders
identifier: "unknown" # Module/wafer/PCB identifier, has to be given (e.g. SCC number)
chip_0: # Arbitrary name of chip, defines folder name with chip data
chip_sn: "W02R01"
chip_id: 0
receiver: "rx0"
chip_config_file: /home/silicon/TJ-Monopix2/2024_03_MAUS_Tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5 # If defined: use config from in file (either .cfg.yaml or .h5). If not defined use chip config of latest scan and std. config if no previous scan exists
record_chip_status: True # Add chip statuses to the output files after the scan (link errors and powering infos)
use_good_pixels_diff: False
send_data: "tcp://127.0.0.1:5500" # Socket address of online monitor
disable_columns: []
module_1: # Arbitrary name of module, defines folder name with chip sub folders
identifier: "unknown" # Module/wafer/PCB identifier, has to be given (e.g. SCC number)
chip_1: # Arbitrary name of chip, defines folder name with chip data
chip_sn: "W08R19"
chip_id: 1
receiver: "rx2"
chip_config_file: /home/silicon/TJ-Monopix2/2024_03_MAUS_Tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5 # If defined: use config from in file (either .cfg.yaml or .h5). If not defined use chip config of latest scan and std. config if no previous scan exists
record_chip_status: True # Add chip statuses to the output files after the scan (link errors and powering infos)
use_good_pixels_diff: False
send_data: "tcp://127.0.0.1:5501" # Socket address of online monitor
disable_columns: []
TLU:
TRIGGER_MODE: 3 # Selecting trigger mode: Use trigger inputs/trigger select (0), TLU no handshake (1), TLU simple handshake (2), TLU data handshake (3)
TRIGGER_SELECT: 0 # Selecting trigger input: HitOr (individual, TDC loop-through) (16), RX1 (multi purpose) (8), RX0 (TDC loop-trough) (4), HitOR [DP_ML_5 and mDP] (logical OR of all eight lines) (3), HitOR [mDP only] (logical OR of all four lines) (2), HitOR [DP_ML_5 only] (logical OR of all four lines) (1), disabled (0)
TRIGGER_INVERT: 0 # Inverting trigger input: HitOr (individual, TDC loop-through) (16), RX1 (multi purpose) (8), RX0 (TDC loop-trough) (4), HitOR [DP_ML_5 and mDP] (logical OR of all eight lines) (3), HitOR [mDP only] (logical OR of all four lines) (2), HitOR [DP_ML_5 only] (logical OR of all four lines) (1), disabled (0)
TRIGGER_LOW_TIMEOUT: 0 # Maximum wait cycles for TLU trigger low.
TRIGGER_VETO_SELECT: 0 # Selecting trigger veto: AZ VETO (2), RX FIFO full (1), disabled (0). Set to (2) if SYNC FE is enabled.
TRIGGER_HANDSHAKE_ACCEPT_WAIT_CYCLES: 5 # TLU trigger minimum length in TLU clock cycles
DATA_FORMAT: 0 # Select trigger data format: only trigger number (0), only time stamp (1), combined, 15 bit time stamp + 16 bit trigger number (2)
EN_TLU_VETO: 0 # Assert TLU veto when external veto. Activate this in order to VETO triggers if SYNC FE is enabled.
TRIGGER_DATA_DELAY: 8 # Depends on the cable length and should be adjusted (run scan/tune_tlu.py)
TDC:
EN_WRITE_TIMESTAMP: 1 # Writing trigger timestamp
EN_TRIGGER_DIST: 1 # Measuring trigger to TDC delay with 640MHz clock
EN_NO_WRITE_TRIG_ERR: 1 # Writing TDC word only if valid trigger occurred
EN_INVERT_TDC: 0 # Inverting TDC input
EN_INVERT_TRIGGER: 0 # Inverting trigger input, e.g. for using Test output from EUDET TLU
hardware: # Setup-specific hardware settings
enable_NTC: True # Only enable if you know you have the correct resistors mounted on the BDAQ board!
electron_conversion: # Charge conversion from DAC to e⁻, typically 8.8 for DC and 13.3 for AC (slightly chip dependent!)
DC_coupled: 8.8
AC_coupled: 13.3
calibration: # Setup-specific calibration constants
bdaq_ntc: # Resistors on BDAQ board for NTC readout
R16: 1.2e6
R17: 20e3
R19: 7.95e3
# Standard analysis settings
# Scans might overwrite these settings if needed.
# Detailed description of parameters in bdaq53/analysis/analysis.py
analysis:
skip: False # Omit analysis in scans
create_pdf: True # Create analysis summary pdf
# module_plotting: True # Create combined plots for chip in a module
store_hits: True # store hit table
cluster_hits: False # store cluster data
# analyze_tdc: False # analyze TDC words
# use_tdc_trigger_dist: False # analyze TDC to TRG distance
# align_method: 0 # how to detect new events
# chunk_size: 1000000 # scales amount of data in RAM (~150 MB)
# blocking: True # block main process during analysis
|
| Attachment 3: testbench_CD.yaml
|
general: # General configuration
readout_system: # Readout system, available platforms are BDAQ53 or MIO3 (+ GPAC). BDAQ53 is default
output_directory: /home/silicon/Data/2024_03_MAUS/TJ-Monopix2/h5 #'/media/raid/data/tjmonopix2/2021-10-25_elsa/tuning' # Top-level output data directory, default is the current folder where the script is started
# Connected Modules
modules:
module_2: # Arbitrary name of module, defines folder name with chip sub folders
identifier: "unknown" # Module/wafer/PCB identifier, has to be given (e.g. SCC number)
chip_2: # Arbitrary name of chip, defines folder name with chip data
chip_sn: "W14R18"
chip_id: 2
receiver: "rx2"
chip_config_file: /home/silicon/TJ-Monopix2/2024_03_MAUS_Tuning/W14R18/20240329_175240_threshold_scan_interpreted.h5
record_chip_status: True # Add chip statuses to the output files after the scan (link errors and powering infos)
use_good_pixels_diff: False
send_data: "tcp://127.0.0.1:5502" # Socket address of online monitor
disable_columns: [484, 485]
module_3: # Arbitrary name of module, defines folder name with chip sub folders
identifier: "unknown" # Module/wafer/PCB identifier, has to be given (e.g. SCC number)
chip_3: # Arbitrary name of chip, defines folder name with chip data
chip_sn: "W18R03"
chip_id: 3
receiver: "rx3"
chip_config_file: /home/silicon/TJ-Monopix2/2024_03_MAUS_Tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5 # If defined: use config from in file (either .cfg.yaml or .h5). If not defined use chip config of latest scan and std. config if no previous scan exists
record_chip_status: True # Add chip statuses to the output files after the scan (link errors and powering infos)
use_good_pixels_diff: False
send_data: "tcp://127.0.0.1:5503" # Socket address of online monitor
disable_columns: [456, 457]
# module_3: # Arbitrary name of module, defines folder name with chip sub folders
# identifier: "unknown" # Module/wafer/PCB identifier, has to be given (e.g. SCC number)
# chip_3: # Arbitrary name of chip, defines folder name with chip data
# chip_sn: "W08R03"
# chip_id: 3
# receiver: "rx3"
# chip_config_file: /home/silicon/TJ-Monopix2/2024_03_MAUS_Tuning/W08R03/20240222_151416_threshold_scan_interpreted.h5 # If defined: use config from in file (either .cfg.yaml or .h5). If not defined use chip config of latest scan and std. config if no previous scan exists
# record_chip_status: True # Add chip statuses to the output files after the scan (link errors and powering infos)
# use_good_pixels_diff: False
# send_data: "tcp://127.0.0.1:5503" # Socket address of online monitor
# disable_columns: []
TLU:
TRIGGER_MODE: 3 # Selecting trigger mode: Use trigger inputs/trigger select (0), TLU no handshake (1), TLU simple handshake (2), TLU data handshake (3)
TRIGGER_SELECT: 0 # Selecting trigger input: HitOr (individual, TDC loop-through) (16), RX1 (multi purpose) (8), RX0 (TDC loop-trough) (4), HitOR [DP_ML_5 and mDP] (logical OR of all eight lines) (3), HitOR [mDP only] (logical OR of all four lines) (2), HitOR [DP_ML_5 only] (logical OR of all four lines) (1), disabled (0)
TRIGGER_INVERT: 0 # Inverting trigger input: HitOr (individual, TDC loop-through) (16), RX1 (multi purpose) (8), RX0 (TDC loop-trough) (4), HitOR [DP_ML_5 and mDP] (logical OR of all eight lines) (3), HitOR [mDP only] (logical OR of all four lines) (2), HitOR [DP_ML_5 only] (logical OR of all four lines) (1), disabled (0)
TRIGGER_LOW_TIMEOUT: 0 # Maximum wait cycles for TLU trigger low.
TRIGGER_VETO_SELECT: 0 # Selecting trigger veto: AZ VETO (2), RX FIFO full (1), disabled (0). Set to (2) if SYNC FE is enabled.
TRIGGER_HANDSHAKE_ACCEPT_WAIT_CYCLES: 5 # TLU trigger minimum length in TLU clock cycles
DATA_FORMAT: 0 # Select trigger data format: only trigger number (0), only time stamp (1), combined, 15 bit time stamp + 16 bit trigger number (2)
EN_TLU_VETO: 0 # Assert TLU veto when external veto. Activate this in order to VETO triggers if SYNC FE is enabled.
TRIGGER_DATA_DELAY: 8 # Depends on the cable length and should be adjusted (run scan/tune_tlu.py)
TDC:
EN_WRITE_TIMESTAMP: 1 # Writing trigger timestamp
EN_TRIGGER_DIST: 1 # Measuring trigger to TDC delay with 640MHz clock
EN_NO_WRITE_TRIG_ERR: 1 # Writing TDC word only if valid trigger occurred
EN_INVERT_TDC: 0 # Inverting TDC input
EN_INVERT_TRIGGER: 0 # Inverting trigger input, e.g. for using Test output from EUDET TLU
hardware: # Setup-specific hardware settings
enable_NTC: True # Only enable if you know you have the correct resistors mounted on the BDAQ board!
electron_conversion: # Charge conversion from DAC to e⁻, typically 8.8 for DC and 13.3 for AC (slightly chip dependent!)
DC_coupled: 8.8
AC_coupled: 13.3
calibration: # Setup-specific calibration constants
bdaq_ntc: # Resistors on BDAQ board for NTC readout
R16: 1.2e6
R17: 20e3
R19: 7.95e3
# Standard analysis settings
# Scans might overwrite these settings if needed.
# Detailed description of parameters in bdaq53/analysis/analysis.py
analysis:
skip: False # Omit analysis in scans
create_pdf: True # Create analysis summary pdf
# module_plotting: True # Create combined plots for chip in a module
store_hits: True # store hit table
cluster_hits: False # store cluster data
# analyze_tdc: False # analyze TDC words
# use_tdc_trigger_dist: False # analyze TDC to TRG distance
# align_method: 0 # how to detect new events
# chunk_size: 1000000 # scales amount of data in RAM (~150 MB)
# blocking: True # block main process during analysis
|
|