Home CMS Production Clean room MedAustron HEPHY testbeams old
testbeam-RD50-DESY-Jul2023 testbeam-RD50-CERN-Oct2022 testbeam-DESY-Oct2017 testbeam-DESY-April2017 testbeam-SPS2015 testbeam-SPS2014 testbeam-DESY14 testbeam-SPS12 testbeam-SPS11 testbeam-SPS10 testbeam-SPS09 testbeam-SPS08 LP-TPC
  Belle testbeam at SPS in June 2015, Page 5 of 6  Not logged in ELOG logo
ID Date Author Project Subject Run Numberup Events XYPosition Cooling Data
  82   Wed Jun 10 19:05:04 2015 Benedikt WürknerSVD3 (H6B)Hardware FEI471500001NoUnknown

RUN WITH SVD3, telescope and FEI4

EUDET Run 71

Mimosa Threshold 6

Pos 1: x=100 mm, y=79 mm (Hits in APV 3 und 8-9 in p-Seite und 14 und 17 in n-Seite )

Downstream FEI4 used

  85   Wed Jun 10 21:36:25 2015 Benedikt WürknerSVD3 (H6B)Horizontal Beam Profile Run72500001NoGood

Trying to get a nice plot of the beam profile by only using the and 3 (horizontal)  see http://elog.hephy.at/testbeam-SPS2015/66 for details. 

Pos 1: x=100 mm, y=79 mm (Hits in APV 3 und 8-9 in p-Seite und 14 und 17 in n-Seite )

Producer.TLU Config Change:

  • AndMask=0x8 
Attachment 1: HW_072_002_Result.pdf
Attachment 2: HW_072_003_Result.pdf
Attachment 3: HW_072_000_Result.pdf
Attachment 4: HW_072_001_Result.pdf
  88   Thu Jun 11 15:56:32 2015 Benedikt WürknerSVD3 (H6B)Hardware FEI473200007NoUnknown

RUN WITH SVD3, telescope and FEI4

EUDET Run 73

Mimosa Threshold 6

Pos 7: x= 30.5 mm, y= 79 mm (wide side center)

Upstream FEI4 used, checking if alignment change helped

  91   Thu Jun 11 17:11:40 2015 Benedikt WürknerSVD3 (H6B)Hardware FEI474200008NoUnknown

RUN WITH SVD3, telescope and FEI4

EUDET Run 74

Mimosa Threshold 6

Pos 8: x=136.08 mm, y= 79 mm (narrow side center)

Upstream FEI4 used

  95   Fri Jun 12 16:52:52 2015 Benedikt WürknerSVD3 (H6B)Telescope without DUT76~30k NoGood

Threshold 6

Testrun to see how the telescope behaves without a DUT to test if there is an increased amount of multiple scattering after the aluminum planes of the FW and BW module. 

 

Attachment 1: Telescope_without_DUT.png
Telescope_without_DUT.png
  98   Fri Jun 12 17:08:23 2015 Benedikt WürknerSVD3 (H6B)Telescope with FEI480~30k NoGood

Threshold 6

Testrun to see how the telescope behaves without a DUT to test if there is an increased amount of multiple scattering after the aluminum planes of the FW and BW module. 

This time with the upstream FEI4 plane

  103   Sat Jun 13 16:47:28 2015 Benedikt WürknerSVD3 (H6B)Mimosa threshold with FEI48212000 NoGood

Set mimosa threshold to 5 and recorded with FEI4 upstream

L3 already in sensor but not yet configured. 

Probably to noisy to help much

  104   Sat Jun 13 17:05:35 2015 Benedikt WürknerSVD3 (H6B)L3 with FEI484300001NoGood

L3 sensor at position x: 105, y: 47 hitting apvs: 2&3 on p-side and apv 3 on n-side

Attachment 1: Telescope_with_L3.png
Telescope_with_L3.png
  105   Sat Jun 13 18:02:04 2015 Benedikt WürknerSVD3 (H6B)L3 with FEI485700002NoGood

L3 sensor at position x: 115, y: 47 hitting apvs: 2&3 on p-side and apv 3&4 on n-side

  106   Sat Jun 13 19:14:41 2015 Benedikt WürknerSVD3 (H6B)L3 with FEI4867320003NoGood

L3 sensor at position x: 115, y: 57 hitting apvs: 1&2 on p-side and apv 3&4 on n-side

  20   Sat Jun 6 16:14:36 2015 Benedikt WürknerSVD3 (H6B)calibration run and setup informationcal01   Unknown

Calibration Run with +- 50V Bias with higher compliance since the p-side draws more current than expected (23muA by the MAMBO)

 

  21   Sat Jun 6 16:17:52 2015 Benedikt WürknerSVD3 (H6B)hardware runhw0025000  Good

Table: 100:70

Bias: +-50V

Run to confirm trigger delay

  22   Sat Jun 6 16:18:48 2015 Benedikt WürknerSVD3 (H6B)hardware runhw00350000  Unknown

Table: 100:70

Bias: +-50V

Run to confirm trigger delay

  24   Sat Jun 6 21:00:15 2015 Benedikt WürknerSVD3 (H6B)first hardware run with TLU and Telescopehw004117171  Unknown

Table: 100:70

Bias: +-50V

600 pedestal

0 offset (at the beginning)

Started APVDAQ and waited till 600 were taken then started EUDAQ

EUDAQ Run 21

Mimosa Thresholds lvl 6

  26   Sun Jun 7 00:58:33 2015 Benedikt WürknerSVD3 (H6B)hardware runhw006   Crap

Table: 100:70

Bias: +-50V

600 pedestal

0 offset (at the beginning)

Started APVDAQ and waited till 600 were taken then started EUDAQ

EUDAQ Run 24

Mimosa Thresholds lvl 7

  29   Sun Jun 7 11:38:04 2015 Benedikt WürknerSVD3 (H6B)hardware run with TLU and Telescopehw00715000  Good

TLU Run 46

Threshold 8b

Offset 601

  33   Sun Jun 7 13:18:20 2015 Benedikt WürknerSVD3 (H6B)hardware run with TLU and Telescopehw008536701NoGood

FIRST GOOD RUN WITH SVD3 plus telescope

EUDET Run 49

Mimosa Threshold 7

Offset APVDAQ-TLU Event number: 601

Pos 1: x=100 mm, y=79 mm (Hits in APV 3 und 8-9 in p-Seite und 14 und 17 in n-Seite)

  37   Sun Jun 7 15:03:31 2015 Thomas BergauerSVD3 (H6B)hardware run with TLU and Telescopehw050500002NoGood

RUN WITH SVD3 plus telescope

EUDET Run 50

Mimosa Threshold 7

Pos 2: x=69.3 mm, y=79 mm (Hits in APV 3-4 und 8-9 in p-Seite und 13 und 18 in n-Seite) 

  40   Sun Jun 7 20:03:09 2015 Thomas BergauerSVD3 (H6B)hardware run with TLU and Telescopehw051500003NoGood

RUN WITH SVD3 plus telescope

EUDET Run 51

Mimosa Threshold 7

Pos 3: x=38.6 mm, y=84 mm

  41   Sun Jun 7 20:03:31 2015 Thomas BergauerSVD3 (H6B)hardware run with TLU and Telescopehw052500004NoGood

RUN WITH SVD3 plus telescope

EUDET Run 52

Mimosa Threshold 7

Pos 4: x=130.7 mm, y=84 mm (hits auf APV 2 und (bisschen) 3, (bisschen) 8 und 9, 15 und 16

ELOG V3.1.5-fc6679b