ID |
Date |
Author |
Project |
Subject |
Run Number |
Events |
XYPosition |
Cooling |
Data |
82
|
Wed Jun 10 19:05:04 2015 |
Benedikt Würkner | SVD3 (H6B) | Hardware FEI4 | 71 | 50000 | 1 | No | Unknown |
RUN WITH SVD3, telescope and FEI4
EUDET Run 71
Mimosa Threshold 6
Pos 1: x=100 mm, y=79 mm (Hits in APV 3 und 8-9 in p-Seite und 14 und 17 in n-Seite )
Downstream FEI4 used |
85
|
Wed Jun 10 21:36:25 2015 |
Benedikt Würkner | SVD3 (H6B) | Horizontal Beam Profile Run | 72 | 50000 | 1 | No | Good |
Trying to get a nice plot of the beam profile by only using the and 3 (horizontal) see http://elog.hephy.at/testbeam-SPS2015/66 for details.
Pos 1: x=100 mm, y=79 mm (Hits in APV 3 und 8-9 in p-Seite und 14 und 17 in n-Seite )
Producer.TLU Config Change:
|
Attachment 1: HW_072_002_Result.pdf
|
Attachment 2: HW_072_003_Result.pdf
|
Attachment 3: HW_072_000_Result.pdf
|
Attachment 4: HW_072_001_Result.pdf
|
88
|
Thu Jun 11 15:56:32 2015 |
Benedikt Würkner | SVD3 (H6B) | Hardware FEI4 | 73 | 20000 | 7 | No | Unknown |
RUN WITH SVD3, telescope and FEI4
EUDET Run 73
Mimosa Threshold 6
Pos 7: x= 30.5 mm, y= 79 mm (wide side center)
Upstream FEI4 used, checking if alignment change helped |
91
|
Thu Jun 11 17:11:40 2015 |
Benedikt Würkner | SVD3 (H6B) | Hardware FEI4 | 74 | 20000 | 8 | No | Unknown |
RUN WITH SVD3, telescope and FEI4
EUDET Run 74
Mimosa Threshold 6
Pos 8: x=136.08 mm, y= 79 mm (narrow side center)
Upstream FEI4 used |
95
|
Fri Jun 12 16:52:52 2015 |
Benedikt Würkner | SVD3 (H6B) | Telescope without DUT | 76 | ~30k | | No | Good |
Threshold 6
Testrun to see how the telescope behaves without a DUT to test if there is an increased amount of multiple scattering after the aluminum planes of the FW and BW module.
|
Attachment 1: Telescope_without_DUT.png
|
|
98
|
Fri Jun 12 17:08:23 2015 |
Benedikt Würkner | SVD3 (H6B) | Telescope with FEI4 | 80 | ~30k | | No | Good |
Threshold 6
Testrun to see how the telescope behaves without a DUT to test if there is an increased amount of multiple scattering after the aluminum planes of the FW and BW module.
This time with the upstream FEI4 plane |
103
|
Sat Jun 13 16:47:28 2015 |
Benedikt Würkner | SVD3 (H6B) | Mimosa threshold with FEI4 | 82 | 12000 | | No | Good |
Set mimosa threshold to 5 and recorded with FEI4 upstream
L3 already in sensor but not yet configured.
Probably to noisy to help much |
104
|
Sat Jun 13 17:05:35 2015 |
Benedikt Würkner | SVD3 (H6B) | L3 with FEI4 | 84 | 30000 | 1 | No | Good |
L3 sensor at position x: 105, y: 47 hitting apvs: 2&3 on p-side and apv 3 on n-side |
Attachment 1: Telescope_with_L3.png
|
|
105
|
Sat Jun 13 18:02:04 2015 |
Benedikt Würkner | SVD3 (H6B) | L3 with FEI4 | 85 | 70000 | 2 | No | Good |
L3 sensor at position x: 115, y: 47 hitting apvs: 2&3 on p-side and apv 3&4 on n-side |
106
|
Sat Jun 13 19:14:41 2015 |
Benedikt Würkner | SVD3 (H6B) | L3 with FEI4 | 86 | 732000 | 3 | No | Good |
L3 sensor at position x: 115, y: 57 hitting apvs: 1&2 on p-side and apv 3&4 on n-side |
20
|
Sat Jun 6 16:14:36 2015 |
Benedikt Würkner | SVD3 (H6B) | calibration run and setup information | cal01 | | | | Unknown |
Calibration Run with +- 50V Bias with higher compliance since the p-side draws more current than expected (23muA by the MAMBO)
|
21
|
Sat Jun 6 16:17:52 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run | hw002 | 5000 | | | Good |
Table: 100:70
Bias: +-50V
Run to confirm trigger delay |
22
|
Sat Jun 6 16:18:48 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run | hw003 | 50000 | | | Unknown |
Table: 100:70
Bias: +-50V
Run to confirm trigger delay |
24
|
Sat Jun 6 21:00:15 2015 |
Benedikt Würkner | SVD3 (H6B) | first hardware run with TLU and Telescope | hw004 | 117171 | | | Unknown |
Table: 100:70
Bias: +-50V
600 pedestal
0 offset (at the beginning)
Started APVDAQ and waited till 600 were taken then started EUDAQ
EUDAQ Run 21
Mimosa Thresholds lvl 6 |
26
|
Sun Jun 7 00:58:33 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run | hw006 | | | | Crap |
Table: 100:70
Bias: +-50V
600 pedestal
0 offset (at the beginning)
Started APVDAQ and waited till 600 were taken then started EUDAQ
EUDAQ Run 24
Mimosa Thresholds lvl 7 |
29
|
Sun Jun 7 11:38:04 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run with TLU and Telescope | hw007 | 15000 | | | Good |
TLU Run 46
Threshold 8b
Offset 601 |
33
|
Sun Jun 7 13:18:20 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run with TLU and Telescope | hw008 | 53670 | 1 | No | Good |
FIRST GOOD RUN WITH SVD3 plus telescope
EUDET Run 49
Mimosa Threshold 7
Offset APVDAQ-TLU Event number: 601
Pos 1: x=100 mm, y=79 mm (Hits in APV 3 und 8-9 in p-Seite und 14 und 17 in n-Seite) |
37
|
Sun Jun 7 15:03:31 2015 |
Thomas Bergauer | SVD3 (H6B) | hardware run with TLU and Telescope | hw050 | 50000 | 2 | No | Good |
RUN WITH SVD3 plus telescope
EUDET Run 50
Mimosa Threshold 7
Pos 2: x=69.3 mm, y=79 mm (Hits in APV 3-4 und 8-9 in p-Seite und 13 und 18 in n-Seite) |
40
|
Sun Jun 7 20:03:09 2015 |
Thomas Bergauer | SVD3 (H6B) | hardware run with TLU and Telescope | hw051 | 50000 | 3 | No | Good |
RUN WITH SVD3 plus telescope
EUDET Run 51
Mimosa Threshold 7
Pos 3: x=38.6 mm, y=84 mm |
41
|
Sun Jun 7 20:03:31 2015 |
Thomas Bergauer | SVD3 (H6B) | hardware run with TLU and Telescope | hw052 | 50000 | 4 | No | Good |
RUN WITH SVD3 plus telescope
EUDET Run 52
Mimosa Threshold 7
Pos 4: x=130.7 mm, y=84 mm (hits auf APV 2 und (bisschen) 3, (bisschen) 8 und 9, 15 und 16 |