Wed Jun 10 18:52:34 2015, Hao Yin, Belle II FADC (H6A), Pedestal, 009, 10000, , Yes, Good
|
temp: in -22 out -18,
FIRRun004, |
Wed Jun 10 19:07:42 2015, Hao Yin, Belle II FADC (H6A), Hardware, 021, , 5, Yes, Good
|
temp: in -23 out -20
FIRRun002,
PedestalRun010,
Calibrationrun002
taget: BW |
Thu Jun 11 11:41:50 2015, Hao Yin, Belle II FADC (H6A), Sixlet Calibration, 011, , , Yes, Good
|
cooled
pedestalrun 008
FIRRun004
max frame pos = 1-2-3. frame n side still shifted
[six]
lvl = 15, 35
lat = 96
sam = 50
grp = 8 |
Thu Jun 11 11:42:39 2015, Hao Yin, Belle II FADC (H6A), Sixlet Calibration, 012, , , Yes, Good
|
cooled until about 400k after that room temp
pedestalrun 009
FIRRun005
sixlet calibration run with only ladders
[six]
lvl = 0, 255
lat = 97
sam = 50
grp = 8 |
Thu Jun 11 16:35:14 2015, Hao Yin, Belle II FADC (H6A), Hardware, 022, , 5, Yes, Good
|
temp: in -23 out -20
FIRRun002,
PedestalRun010,
Calibrationrun002
taget: BW, pos 5 |
Thu Jun 11 16:38:17 2015, Hao Yin, Belle II FADC (H6A), Hardware, 023, , 7, Yes, Good
|
temp: attachment (in 1st col, out 2nd col)
FIRRun002,
PedestalRun010,
Calibrationrun002
taget: CE, pos 7 |
Thu Jun 11 18:01:54 2015, Hao Yin, Belle II FADC (H6A), Hardware, 024, , 6, Yes, Good
|
temp: attachment (in 1st col, out 2nd col)
FIRRun002,
PedestalRun010,
Calibrationrun002
taget: -z, pos 6 |
Thu Jun 11 18:37:11 2015, Hao Yin, Belle II FADC (H6A), Hardware, 025, , 6, Yes, Good
|
temp: attachment (in 1st col, out 2nd col)
FIRRun002,
PedestalRun010,
Calibrationrun002
taget: ce, pos 3 |
Fri Jun 12 09:31:58 2015, Hao Yin, Belle II FADC (H6A), FIR, 005, , , Yes, Good
|
FIR filer and ADC delay for long sixlet cal run. |
Fri Jun 12 17:00:18 2015, Hao Yin, Belle II FADC (H6A), Pedestal, 011, 10000, , No, Good
|
cooled pedestal vaules for long sixlet cal |
Fri Jun 12 17:03:02 2015, Hao Yin, Belle II FADC (H6A), Pedestal, 012, 10000, , No, Good
|
room temp
FIRRun002
|
Fri Jun 12 17:11:45 2015, Hao Yin, Belle II FADC (H6A), Hardware, 026, 50k, 1, No, Good
|
room temp
FIRRun002,
PedestalRun012,
CalibrationRun003
L3 rotated.
taget: bw, pos 1
|
Sat Jun 13 09:09:37 2015, Hao Yin, Belle II FADC (H6A), Hardware, 027, ~200k, 2, No, Good
|
room temp
FIRRun002,
PedestalRun012,
CalibrationRun003
L3 rotated.
taget: CE, pos 1
|
Sat Jun 13 10:07:36 2015, Hao Yin, Belle II FADC (H6A), Hardware, 028, 50k, 4, No, Good
|
room temp
FIRRun002,
PedestalRun012,
CalibrationRun003
L3 rotated.
taget: FW, pos 4
|
Sat Jun 13 13:01:39 2015, Hao Yin, Belle II FADC (H6A), Hardware, 029, , 3, No, Good
|
room temp
FIRRun002,
PedestalRun012,
CalibrationRun003
L3 rotated.
taget: CE, pos 3
|
Sat Jun 13 19:26:26 2015, Hao Yin, Belle II FADC (H6A), Hardware, 030, , 3, No, Good
|
room temp
FIRRun002,
PedestalRun012,
CalibrationRun003
wo L3 and L4
taget: CE, pos 3
|
Sat Jun 13 19:29:50 2015, Hao Yin, Belle II FADC (H6A), Hardware, 030, , 1, No, Good
|
room temp
FIRRun002,
PedestalRun012,
CalibrationRun003
wo L3 and L4
taget: bw, pos 1
|
Tue May 12 10:27:39 2015, Benedikt Würkner, SVD3 (H6B), Setup information, , , , , Unknown
|
Information concerning the SVD3 setup during a beam test
In the beam area setup the whole crate and the power supply with the usual spider cable and the two Keithly 2410 high voltage supplies. Monitoring of the 2410 happens via a NI MAX interface that connects to the GPIB-Ethernet interface and needs to be configured there. The IP and password are noted on the device. The software can be found on heros in medialib/LONGTERM/longterm R3.1_doubleSided as a normal *.vi file.
Default adresses 16 and 17 as defined in labview, need to figure out on site which is which, if the voltage selected (e.g. 100V) is applied as +50/-50 or if it is applied as +100/-100 before connecting the cables.
Take a run without dut as well to check the telescope integrity. Without dut in beamline!!!!! |
Thu Jun 4 18:49:03 2015, Benedikt Würkner, SVD3 (H6B), Setup, , , , , Unknown
|
|
Sat Jun 6 16:14:36 2015, Benedikt Würkner, SVD3 (H6B), calibration run and setup information, cal01, , , , Unknown
|
Calibration Run with +- 50V Bias with higher compliance since the p-side draws more current than expected (23muA by the MAMBO)
|
|