Home CMS Production Clean room MedAustron HEPHY testbeams old
testbeam-RD50-DESY-Jul2023 testbeam-RD50-CERN-Oct2022 testbeam-DESY-Oct2017 testbeam-DESY-April2017 testbeam-SPS2015 testbeam-SPS2014 testbeam-DESY14 testbeam-SPS12 testbeam-SPS11 testbeam-SPS10 testbeam-SPS09 testbeam-SPS08 LP-TPC
  Belle testbeam at SPS in June 2015, Page 3 of 6  Not logged in ELOG logo
New entries since:Thu Jan 1 01:00:00 1970
ID Date Author Project Subject Run Number Eventsup XYPosition Cooling Data
  108   Sat Jun 13 19:29:50 2015 Hao YinBelle II FADC (H6A)Hardware030 1NoGood

room temp

FIRRun002,
PedestalRun012,
CalibrationRun003

wo L3 and L4
taget: bw, pos 1
 

  5   Thu Jun 4 14:16:20 2015 Hao YinBelle II FADC (H6A)Pedestal00110000  Good

FirRun001, room temp
telescope n-side switched.

  8   Thu Jun 4 18:45:42 2015 Hao YinBelle II FADC (H6A)Pedestal00310000  Good

firrun003, room temp
 

  15   Fri Jun 5 19:59:44 2015 Hao YinBelle II FADC (H6A)Pedestal00410000  Good

update pedestal values for room temp sixlet runs.
 

  16   Fri Jun 5 23:38:51 2015 Hao YinBelle II FADC (H6A)Pedestal00510000  Unknown

Readjust after cooling box.

room temp, firrun002
 

  27   Sun Jun 7 10:36:38 2015 Hao YinBelle II FADC (H6A)Pedestal00610000  Unknown

Cooled, Temp see attachment
FirRun002
 

  62   Tue Jun 9 09:32:41 2015 Hao YinBelle II FADC (H6A)Pedestal00710000  Good

Room temp, fir002

  73   Tue Jun 9 20:32:46 2015 Hao YinBelle II FADC (H6A)Pedestal00810000 NoGood

Room temp, fir004

  81   Wed Jun 10 18:52:34 2015 Hao YinBelle II FADC (H6A)Pedestal00910000 YesGood

temp: in -22 out -18,
FIRRun004,

  96   Fri Jun 12 17:00:18 2015 Hao YinBelle II FADC (H6A)Pedestal01110000 NoGood

cooled pedestal vaules for long sixlet cal

  97   Fri Jun 12 17:03:02 2015 Hao YinBelle II FADC (H6A)Pedestal01210000 NoGood

room temp
FIRRun002
 

  24   Sat Jun 6 21:00:15 2015 Benedikt WürknerSVD3 (H6B)first hardware run with TLU and Telescopehw004117171  Unknown

Table: 100:70

Bias: +-50V

600 pedestal

0 offset (at the beginning)

Started APVDAQ and waited till 600 were taken then started EUDAQ

EUDAQ Run 21

Mimosa Thresholds lvl 6

  103   Sat Jun 13 16:47:28 2015 Benedikt WürknerSVD3 (H6B)Mimosa threshold with FEI48212000 NoGood

Set mimosa threshold to 5 and recorded with FEI4 upstream

L3 already in sensor but not yet configured. 

Probably to noisy to help much

  45   Sun Jun 7 23:09:46 2015 Benedikt WürknerSVD3 (H6B)hardware run with TLU and Telescopehw0541200006NoGood

RUN WITH SVD3 plus telescope

EUDET Run 54

Mimosa Threshold 6

Pos 6: x=136.08 mm, y= 91.49 mm (narrow side top)

  30   Sun Jun 7 12:10:24 2015 Benedikt WürknerSVD3 (H6B)Telescope Threshold8b test run 004614399  Unknown

Telescope in combination with SVD3

  29   Sun Jun 7 11:38:04 2015 Benedikt WürknerSVD3 (H6B)hardware run with TLU and Telescopehw00715000  Good

TLU Run 46

Threshold 8b

Offset 601

  10   Thu Jun 4 22:07:16 2015 Hao YinBelle II FADC (H6A)Hardware003189k3NoGood

CE. pedestal run 003. Fir run 002. Room temp

  53   Mon Jun 8 15:03:53 2015 Benedikt WürknerSVD3 (H6B)hardware run with TLU and FEI4 WORKING5919000  Unknown

Testrun with the FEI4 working for the first time. 

Lessons learned about the configuration:

EnableDUTVeto needs to be set for the FEI4 to allow it to work

HandShakeMode needs to be enabled for the FEI4 as well

"Enable RJ45 input during scans" needs to be enabled for the USB-controller

  88   Thu Jun 11 15:56:32 2015 Benedikt WürknerSVD3 (H6B)Hardware FEI473200007NoUnknown

RUN WITH SVD3, telescope and FEI4

EUDET Run 73

Mimosa Threshold 6

Pos 7: x= 30.5 mm, y= 79 mm (wide side center)

Upstream FEI4 used, checking if alignment change helped

  91   Thu Jun 11 17:11:40 2015 Benedikt WürknerSVD3 (H6B)Hardware FEI474200008NoUnknown

RUN WITH SVD3, telescope and FEI4

EUDET Run 74

Mimosa Threshold 6

Pos 8: x=136.08 mm, y= 79 mm (narrow side center)

Upstream FEI4 used

ELOG V3.1.5-fc6679b