ID |
Date |
Author |
Project |
Subject |
Run Number |
Events |
XYPosition |
Cooling |
Data |
108
|
Sat Jun 13 19:29:50 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 030 | | 1 | No | Good |
room temp
FIRRun002,
PedestalRun012,
CalibrationRun003
wo L3 and L4
taget: bw, pos 1
|
5
|
Thu Jun 4 14:16:20 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 001 | 10000 | | | Good |
FirRun001, room temp
telescope n-side switched. |
8
|
Thu Jun 4 18:45:42 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 003 | 10000 | | | Good |
firrun003, room temp
|
15
|
Fri Jun 5 19:59:44 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 004 | 10000 | | | Good |
update pedestal values for room temp sixlet runs.
|
16
|
Fri Jun 5 23:38:51 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 005 | 10000 | | | Unknown |
Readjust after cooling box.
room temp, firrun002
|
27
|
Sun Jun 7 10:36:38 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 006 | 10000 | | | Unknown |
Cooled, Temp see attachment
FirRun002
|
62
|
Tue Jun 9 09:32:41 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 007 | 10000 | | | Good |
Room temp, fir002 |
73
|
Tue Jun 9 20:32:46 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 008 | 10000 | | No | Good |
Room temp, fir004 |
81
|
Wed Jun 10 18:52:34 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 009 | 10000 | | Yes | Good |
temp: in -22 out -18,
FIRRun004, |
96
|
Fri Jun 12 17:00:18 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 011 | 10000 | | No | Good |
cooled pedestal vaules for long sixlet cal |
97
|
Fri Jun 12 17:03:02 2015 |
Hao Yin | Belle II FADC (H6A) | Pedestal | 012 | 10000 | | No | Good |
room temp
FIRRun002
|
24
|
Sat Jun 6 21:00:15 2015 |
Benedikt Würkner | SVD3 (H6B) | first hardware run with TLU and Telescope | hw004 | 117171 | | | Unknown |
Table: 100:70
Bias: +-50V
600 pedestal
0 offset (at the beginning)
Started APVDAQ and waited till 600 were taken then started EUDAQ
EUDAQ Run 21
Mimosa Thresholds lvl 6 |
103
|
Sat Jun 13 16:47:28 2015 |
Benedikt Würkner | SVD3 (H6B) | Mimosa threshold with FEI4 | 82 | 12000 | | No | Good |
Set mimosa threshold to 5 and recorded with FEI4 upstream
L3 already in sensor but not yet configured.
Probably to noisy to help much |
45
|
Sun Jun 7 23:09:46 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run with TLU and Telescope | hw054 | 120000 | 6 | No | Good |
RUN WITH SVD3 plus telescope
EUDET Run 54
Mimosa Threshold 6
Pos 6: x=136.08 mm, y= 91.49 mm (narrow side top) |
30
|
Sun Jun 7 12:10:24 2015 |
Benedikt Würkner | SVD3 (H6B) | Telescope Threshold8b test run | 0046 | 14399 | | | Unknown |
Telescope in combination with SVD3 |
29
|
Sun Jun 7 11:38:04 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run with TLU and Telescope | hw007 | 15000 | | | Good |
TLU Run 46
Threshold 8b
Offset 601 |
10
|
Thu Jun 4 22:07:16 2015 |
Hao Yin | Belle II FADC (H6A) | Hardware | 003 | 189k | 3 | No | Good |
CE. pedestal run 003. Fir run 002. Room temp |
53
|
Mon Jun 8 15:03:53 2015 |
Benedikt Würkner | SVD3 (H6B) | hardware run with TLU and FEI4 WORKING | 59 | 19000 | | | Unknown |
Testrun with the FEI4 working for the first time.
Lessons learned about the configuration:
EnableDUTVeto needs to be set for the FEI4 to allow it to work
HandShakeMode needs to be enabled for the FEI4 as well
"Enable RJ45 input during scans" needs to be enabled for the USB-controller |
88
|
Thu Jun 11 15:56:32 2015 |
Benedikt Würkner | SVD3 (H6B) | Hardware FEI4 | 73 | 20000 | 7 | No | Unknown |
RUN WITH SVD3, telescope and FEI4
EUDET Run 73
Mimosa Threshold 6
Pos 7: x= 30.5 mm, y= 79 mm (wide side center)
Upstream FEI4 used, checking if alignment change helped |
91
|
Thu Jun 11 17:11:40 2015 |
Benedikt Würkner | SVD3 (H6B) | Hardware FEI4 | 74 | 20000 | 8 | No | Unknown |
RUN WITH SVD3, telescope and FEI4
EUDET Run 74
Mimosa Threshold 6
Pos 8: x=136.08 mm, y= 79 mm (narrow side center)
Upstream FEI4 used |