Infineon old
multi hit
Voltage=300V, I=10.4028uA
(new table calibration): V:75, H:96.5
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: run000999
DaqEvents: 63913 (-600 ped)
EUDAQ EVENTS: daq events - 600 (+2 offset)
(new table calibration): V:75, H:95
EUDAQ File: run000998
DaqEvents: 526562 (-600 ped)
Der zweite PM (entsprechend der Beamrichtung) war von Anfang an nicht angeschlossen an die TLU! Stattdessen war ein Atlas pixel sensor, welcher als 4ter PM fungiert angeschlossen. Genau dieser "PM" hatte 0 counts bei der TLU --> Igor sagt, dass dieser Sensor ("PM") anscheinend keine Versorgungsspannung hatte (~400V). Jetzt baut Igor diesen Atlas Sensor wieder aus und hat bereits den nicht angeschlossenen PM wieder angeschlossen an die TLU. DIeser PM zeigt aber nun zu viele counts. Deshalb behalten wir die AND mask 11 (auch jetzt bei den Belle Modulen).
L5_p_side APV #3 faulty signal
L4_n_side APV #2 and #3 faulty signal
We set the coordinates trying to put the beam in an area with well working APVs
Peak of course differs for n and p sensors due to their different pitch.
L4-6 n-side Peak around strip 180
L4&6 p-side mean value around strip 380
L5 p-side moved by 4.8mm due to reasons (APV misalignment I think) therefore the peak of the same measurements is moved by 4.8/75µm = 64 strips therefore centered around strip 320
The coordinates of the x-y table were set to 0:0 at this point. Refer to Run Alignment2 for reference data.
Cooled see appendix
with new layout (l3_n-side channels changed and reactivated).
Latest FIRRun
cooled see appendix (FIRRun003)
MaxEvents 10000
cooled see appendix (FIRRun_003)
PedestalRun_009
cooling see attachment of FIRRun003
Ped 009
Cal 005
Multi 6 raw mode
L5_n_side out of order
FIFO_FULL_ERROR starting at ~2000 events
cooled see appendix (FirRun003) PedestalRun_010 multi 6 Raw Mode FIFO size increased L3n deactivated 100000 deadtime (CTRL TRG) Zero_suppressed
cooled see appendix (FirRun003) PedestalRun_010 multi 6 Raw Mode FIFO size increased L3n deactivated 100000 deadtime (CTRL TRG)
VME Error, overnight run
Not completely cooled since cooling failed at 1:42 in the night
Bias voltage set to +-60V
Some error with event no17 or 18 leading to the data not being easily analysable requiring a hack in TuxOA
Pedestal_013 (cooled)
Noisefile: HardwareRun_036.noi
Hardware Run +-30V Bias
Room Temperature
Pedestal 017 (again marked all the bad strips)
Zero Suppressed
Hardware Run +-50V Bias
Pedestal 018 (again marked all the bad strips)
Hardware Run +-60V Bias
fachi: aimhephy@antispam.e4ward.com
chrisu: gargamel0971
flo: flo.bux@sbg.at
shorty: martin@kurznet.net
markus; mueffi1040
hao: hao.yin@gmx.at
benni: benedikt.wuerkner@assoc.oeaw.ac.at
juan: juan.garcia.ferrero@cern.ch
axel: ???
bergi: callmebergi