ID |
Date |
Author |
Project |
Subject |
Run Number |
Events |
StartTime |
EndTime |
Data |
121
|
Sun Nov 23 18:26:54 2014 |
Markus Friedl | Belle SVD | HardwareRun | 005 | 60600 | 23.11.2014 18:24:34 | 23.11.2014 | Good |
Hardware run, hitting APVs 2/3 on p-sides, 1/2 on n-sides
EUDAT telescope running with difference of 2 events |
120
|
Sun Nov 23 17:51:44 2014 |
Benedikt Würkner | Belle SVD | HardwareRun | 046 | 100000 | 20:06 | 20:36 | Unknown |
Hardware Run +-60V Bias
Room Temperature
Pedestal 018 (again marked all the bad strips)
Zero Suppressed
|
119
|
Sun Nov 23 16:55:37 2014 |
Markus Friedl | Belle SVD | HardwareRun | 004 | 60600 | 23.11.2014 16:51:49 | 23.11.2014 18:23:54 | Good |
Hardware run, hitting APVs 1/2 on p-sides, 1/2 on n-sides
EUDAT telescope running with difference of 2 events |
118
|
Sun Nov 23 15:13:37 2014 |
Markus Friedl | Belle SVD | HardwareRun | 003 | 100600 | 23.11.2014 14:07:23 | 23.11.2014 16:51:27 | Good |
Hardware run, hitting APVs 0/1 on p-sides, 1/2 on n-sides
EUDAT telescope running with difference of 2 events |
117
|
Sun Nov 23 15:10:42 2014 |
Markus Friedl | Belle SVD | CalibrationRun | 001 | 83400 | | | Good |
Initial calibration run with SVD3 setup and WedgeOld, FW993, BW993 (reading out 4 chips on every p-side) |
116
|
Sun Nov 23 15:09:53 2014 |
Markus Friedl | Belle SVD | PedestalRun | 001 | 10000 | | | Good |
Initial pedestal run with SVD3 setup and WedgeOld, FW993, BW993 (reading out 4 chips on every p-side) |
115
|
Sun Nov 23 15:07:54 2014 |
Markus Friedl | Belle SVD | common | | | | | Unknown |
Geometry setup of FW/BW:
(all dimensions are in mm and refer to the sensor planes) |
114
|
Sun Nov 23 12:55:47 2014 |
Benedikt Würkner | Belle SVD | HardwareRun | 045 | 20000 | | | Unknown |
Hardware Run +-50V Bias
Room Temperature
Pedestal 018 (again marked all the bad strips)
Zero Suppressed |
113
|
Sun Nov 23 12:39:45 2014 |
Axel König | common | PMT's of EUDET (Igor Rubinsky) | | | | | Unknown |
Der zweite PM (entsprechend der Beamrichtung) war von Anfang an nicht angeschlossen an die TLU! Stattdessen war ein Atlas pixel sensor, welcher als 4ter PM fungiert angeschlossen. Genau dieser "PM" hatte 0 counts bei der TLU --> Igor sagt, dass dieser Sensor ("PM") anscheinend keine Versorgungsspannung hatte (~400V). Jetzt baut Igor diesen Atlas Sensor wieder aus und hat bereits den nicht angeschlossenen PM wieder angeschlossen an die TLU. DIeser PM zeigt aber nun zu viele counts. Deshalb behalten wir die AND mask 11 (auch jetzt bei den Belle Modulen). |
112
|
Sun Nov 23 12:17:59 2014 |
Benedikt Würkner | Belle SVD | HardwareRun | 044 | 20000 | | | Unknown |
Hardware Run +-30V Bias
Room Temperature
Pedestal 017 (again marked all the bad strips)
Zero Suppressed |
111
|
Sun Nov 23 10:51:49 2014 |
Hao Yin | Belle SVD | HardwareRun | 042 | 76863 | | | Unknown |
Hardware Run +-40V Bias
Room Temperature
Pedestal 016
Zero Suppressed |
110
|
Sun Nov 23 10:32:41 2014 |
Hao Yin | Belle SVD | PedestalRun | 016 | 10000 | | | Unknown |
Pedestal Run
room temperature (30C)
Bias scans planned |
109
|
Sun Nov 23 09:49:00 2014 |
Markus Friedl | Belle SVD | cooling | | | | | Unknown |
Saturday evening, the cooling became unstable which indicates the end of the CO2 supply, possibly having a mixture of liquid and gas phases.
Strange oscillations observed for the DUT temperatures until the MF valve was finally turned off close to midnight.
|
108
|
Sun Nov 23 09:36:27 2014 |
Axel König | Infineon | hardware run | Infineon_old_run006 | 526562 | | | Unknown |
Infineon old
multi hit
Voltage=300V, I=10.4028uA
(new table calibration): V:75, H:95
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: run000998
DaqEvents: 526562 (-600 ped)
EUDAQ EVENTS: daq events - 600 (+2 offset) |
107
|
Sun Nov 23 09:32:48 2014 |
Axel König | Infineon | hardware run | Infineon_old_run007 | 63913 | | | Unknown |
Infineon old
multi hit
Voltage=300V, I=10.4028uA
(new table calibration): V:75, H:96.5
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: run000999
DaqEvents: 63913 (-600 ped)
EUDAQ EVENTS: daq events - 600 (+2 offset) |
106
|
Sun Nov 23 01:37:42 2014 |
Hao Yin | Belle SVD | HardwareRun | 040 | 20000 | 2014-11-23 01:37:00 | | Unknown |
Bias voltage set to +-80V
Pedestal_015 (cooled)
"New" layout with no cooling (CO2 is no more)
Newly set values for APC Delay
New FIR Run 005
Temperature around 30 C
Bias: +-80V |
105
|
Sun Nov 23 01:05:43 2014 |
Hao Yin | Belle SVD | HardwareRun | 039 | 20000 | 2014-11-22 15:18:40 | | Crap |
Cooled down to -20
Bias voltage set to +-80V
Pedestal_013 (cooled)
Noisefile: HardwareRun_036.noi
|
103
|
Sun Nov 23 00:51:07 2014 |
Axel König | Infineon | hardware run | Infineon_old_run005 | 26569 | | | Unknown |
Infineon old
multi hit
Voltage=300V, I=10.4609uA
(new table calibration): V:75, H:94.5
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: run000997
DaqEvents: 26569 (-600 ped)
EUDAQ EVENTS: daq events - 600 (+2 offset)
|
|
102
|
Sun Nov 23 00:24:15 2014 |
Axel König | Infineon | hardware run | Infineon_old_run004 | 168725 | | | Unknown |
Infineon old
multi hit
Voltage=300V, I=10.6529uA
(new table calibration): V:81, H:88
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: run000996
DaqEvents: 168725 (-600 ped)
EUDAQ EVENTS: daq events - 600 (+2 offset) |
101
|
Sun Nov 23 00:20:41 2014 |
Axel König | Infineon | hardware run | Infineon_old_run003 | 30000 | | | Unknown |
Infineon old
multi hit
Voltage=300V, I=10.9797uA
(new table calibration): V:?, H:?
config: L:\cern14\AIDA
data: L:\cern14\AIDA
EUDAQ File: run000994
DaqEvents: 30000 (-600 ped)
EUDAQ EVENTS: daq events - 600 (+2 offset) |