ID |
Date |
Author |
Project |
Subject |
Run Number |
Events |
StartTime |
EndTime |
103
|
Sat Oct 9 00:17:02 2010 |
Markus Friedl | BELLE | run | run056 | 225k | 09.10.2010 00:15:53 | 09.10.2010 09:54:28 |
Belle stack w/o Origami2 after irradiation
HV=80V / I_start=255 µA, I_stop=243 µA
cooling: Origami only, chiller set to -25°C,
2 suspicious APVs on n side of Micron (possibly due to burnt strip)
same position as in previous run
telescope run 20198 - now with correct telescope threshold settings
a lot of "Error detected in APV 21, subevent 2. Event discarded, reset sent." errors started at 09.10.2010 09:00:25 (after whole night without any error) |
104
|
Sat Oct 9 12:00:55 2010 |
Christian Irmler | BELLE | cal | cal017 | 83800 | 09.10.2010 11:59:37 | |
Origami1 (n-side only) + Micron1 (non-irrad)
angle scan: 73°
HV=100V / 40 µA
cooling: chiller set to 15°C
Origami p-side does not receive triggers -> disabled
origami flex straight part needed to be folded due to severe rotation angle -> nanonics connector problem... |
105
|
Sat Oct 9 12:25:36 2010 |
Thomas Bergauer | BELLE | run | run057 | 276475 | 09.10.2010 12:22:21 | 09.10.2010 15:08:46 |
Origami1 (n-side only) + Micron1 (non-irrad)
angle scan: 73 degree
HV=100V / 36 uA (beginning), 35uA (end of run)
cooling: chiller set to 15C
PROBLEM: wrong config file (single hit, not multi6)
telescope run 20200
Origami p-side does not receive triggers -> disabled
origami flex straight part needed to be folded due to severe rotation angle -> nanonics connector problem...
|
|
106
|
Sat Oct 9 15:29:09 2010 |
Markus Friedl | BELLE | run | run058 | 30000 | 09.10.2010 15:26:50 | 09.10.2010 16:21:37 |
Origami1 (n-side only) + Micron1 (non-irrad)
angle scan: 73 - now with multi6 (previous run was single)
HV=100V / 35uA (beginning of run) 34uA (end of run)
cooling: chiller set to 15C
telescope run 20201
Origami p-side does not receive triggers -> disabled
origami flex straight part needed to be folded due to severe rotation angle -> nanonics connector problem...
|
|
107
|
Sat Oct 9 18:56:35 2010 |
Thomas Bergauer | common | path to telescope data | | | | |
eudetmac001.cern.ch
path is /Volumes/Data/eudet/Data/cern_2010_sept_silc_apvdaq (Vienna system)
and /Volumes/Data/eudet/Data/cern_2010_sept_silc_alibava (Santander system) |
108
|
Sat Oct 9 19:44:36 2010 |
Markus Friedl | common | end of success | | | 09.10.2010 19:44:23 | NaN |
|
109
|
Sun Oct 10 15:45:04 2010 |
Thomas Bergauer | common | end of success | | | 09.10.2010 19:44:23 | NaN |
;-)
genau das gleiche wollte ich auch gerade schreiben! |
110
|
Mon Oct 11 11:18:17 2010 |
Christian Irmler | common | end of success | | | 09.10.2010 19:44:23 | NaN |
der Beiweis :-) |
Attachment 1: IMG_9033.JPG
|
|
111
|
Tue Oct 19 14:58:56 2010 |
Manfred Valentan | Micron Baby | geometry | | | | |
|
Attachment 1: IMG_8888.JPG
|
|
Attachment 2: micron_baby_stack_telescope_geometry.JPG
|
|
Attachment 3: micron_baby_stack_telectope_geometry.dwg
|
112
|
Thu Mar 31 10:28:19 2011 |
Manfred Valentan | Micron Baby | DUT5, source run, post irrad, pre zupf | cal100 | | 31.03.2011 10:24:59 | 31.03.2011 10:33:15 |
DUT5
cal-file: micronbaby_single_irrad_cal100.cfg
HV=+-50V
90Sr 1mCi ~centered
I_start=99muA
I_end=103muA
|
113
|
Thu Mar 31 11:05:39 2011 |
Manfred Valentan | Micron Baby | DUT5, source run, post irrad, pre zupf | run100 | 100k | 31.03.2011 11:02:17 | 31.03.2011 11:15:41 |
DUT5
cal-file: micronbaby_multi6_irrad_run100.cfg
HV=+-50V
90Sr 1mCi ~centered
I_start=104µA
I_end=111µA
|
114
|
Thu Mar 31 12:11:04 2011 |
Manfred Valentan | Micron Baby | DUT4, source run, post irrad, pre zupf | cal101 | | 31.03.2011 12:09:36 | 31.03.2011 12:17:52 |
DUT4
config file: micronbaby_single_irrrad_cal101.cfg
HV=+-50V
90Sr 1mCi ~centered
I_start=128µA
I_end=140µA
|
115
|
Thu Mar 31 12:24:24 2011 |
Manfred Valentan | Micron Baby | DUT4, source run, post irrad, pre zupf | run101 | 100k | 31.03.2011 12:23:00 | 31.03.2011 12:36:48 |
DUT4
config file: micronbaby_multi6_irrrad_run101.cfg
HV=+-50V
90Sr 1mCi ~centered
I_start=128µA
I_end=155µA
|
116
|
Fri Apr 8 13:25:58 2011 |
Manfred Valentan | Micron Baby | sensors and modules | | | | |
TRK1: B2Micron_2826_1_baby2
TRK2: B2Micron_2826_1_baby3
DUT3: B2Micron_2826_7_baby2 (common p-stop)
DUT4: B2Micron_2826_19_baby4 (combined p-stop)
DUT5: B2Micron_2826_19_baby3 (atoll p-stop)
TRK6: B2Micron_2826_1_baby4
TRK7: B2Micron_2826_19_baby2
GEW: B2Micron_2826_7_baby4
not used: B2Micron_2826_7_baby3 |
117
|
Mon Apr 11 18:25:35 2011 |
Manfred Valentan | Micron Baby | DUT5, source run, post irrad, pre zupf | cal104 | 83800 | 11.04.2011 18:12:38 | 11.04.2011 18:20:50 |
DUT5 (atoll)
config file: D:/cern10/micronbaby/data_lab/DUT5/micronbaby_single_irrrad.cfg
HV=+-50V
90Sr 1mCi ~centered
I_start=26µA
I_end=48µA
|
118
|
Mon Apr 11 18:37:28 2011 |
Manfred Valentan | Micron Baby | DUT5, source run, post irrad, pre zupf | run104 | 100k | 11.04.2011 18:25:28 | 11.04.2011 18:32:11 |
DUT5 (atoll)
config file: D:/cern10/micronbaby/data_lab/DUT5/micronbaby_multi6_irrrad.cfg
HV=+-50V
90Sr 1mCi ~centered
I_start=50µA
I_end=95µA
|
119
|
Wed Apr 13 12:13:09 2011 |
Manfred Valentan | Micron Baby | DUT5, source run, post irrad, post zupf ** DO NOT USE ** | cal105 | 83800 | 13.04.2011 12:02:41 | 13.04.2011 12:10:55 |
DUT5 (atoll), each second bond removed to simulate intermediate strips
config file: D:/cern10/micronbaby/data_lab/DUT5/micronbaby_single_irrrad.cfg
HV=+-50V
90Sr 1mCi ~centered
I_start=18µA
I_end=21.5µA
data recorded with new switching power supplies and old intcal, which doesn't ignore bad strips!!!!! |
120
|
Wed May 4 15:14:31 2011 |
Thomas Bergauer | Pt | info about module | | | | |
pt-Modul hat jeweils zwei OB1 Sensoren von STM (mit 122um Pitch)
im Abstand von 2mm uebereinander |
121
|
Wed May 11 16:28:07 2011 |
Manfred Valentan | Micron Baby | DUT5, source run, post irrad, post zupf | run106 | 100k | 11.05.2011 16:00 | 11.05.2011 16:25 |
DUT5 (atoll)
config file: D:/cern10/micronbaby/data_lab/DUT5/micronbaby_multi6_irrrad.cfg
HV=+-50V
90Sr 1mCi ~centered
I_start=52µA
I_end=120µA
DAQ modified so that only strips marked as good are considered when calculating the common mode correction. |
122
|
Wed May 11 16:28:20 2011 |
Manfred Valentan | Micron Baby | DUT5, source run, post irrad, post zupf | cal106 | 100k | 11.05.2011 16:00 | 11.05.2011 16:25 |
DUT5 (atoll)
config file: D:/cern10/micronbaby/data_lab/DUT5/micronbaby_multi6_irrrad.cfg
HV=+-50V
90Sr 1mCi ~centered
I_start=52µA
I_end=120µA
DAQ modified so that only strips marked as good are considered when calculating the common mode correction. |