| ID |
Date |
Author |
Subject |
Run Number |
DUT |
Beam Energy |
Rate Setting |
Particle Type |
Data |
t-Start |
t-Stop |
Duration_min |
Frontend |
Phantom |
Phantom thickness |
|
238
|
Sat Sep 20 20:41:39 2025 |
elog_producer | Caribou 1.5 | | RD50-MPW4 | 800 MeV | Low Flux High | Proton | Unknown | | | | Normal | | | | data collector starts to loose frames |
|
239
|
Sat Sep 20 20:58:41 2025 |
elog_producer | Caribou 1.5 | 1040 | RD50-MPW4 | 800 MeV | Low Flux High | Proton | Unknown | 20.09.2025 20:51:57 | 20.09.2025 20:58:53 | 6 | Normal | | | automatic log for run 1040
Comment:
this time no RX drops |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -190
[Producer.tracker_irgendwas]
|
|
240
|
Sat Sep 20 20:59:07 2025 |
elog_producer | Caribou 1.5 | | RD50-MPW4 | 800 MeV | Low Flux High | Proton | Unknown | | | | Normal | | | | lost one right at the end 20:58:44 |
|
241
|
Sat Sep 20 21:00:14 2025 |
elog_producer | Caribou 1.5 | | RD50-MPW4 | 800 MeV | Low Flux High | Proton | Unknown | | | | Normal | | | | changing Peary readout to DMA |
|
242
|
Sat Sep 20 21:00:20 2025 |
elog_producer | Caribou 1.5 | | RD50-MPW4 | 800 MeV | Low Flux High | Proton | Unknown | | | | Normal | | | | changing Peary readout to DMA |
|
243
|
Sat Sep 20 21:02:14 2025 |
elog_producer | Caribou 1.5 | 1041 | RD50-MPW4 | 800 MeV | Low Flux High | Proton | Unknown | 20.09.2025 21:01:34 | 20.09.2025 21:02:26 | 0 | Normal | | | automatic log for run 1041
Comment:
no data from DMA  |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 1
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/dma/dma_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -190
[Producer.tracker_irgendwas]
|
|
244
|
Sat Sep 20 21:12:30 2025 |
elog_producer | Caribou 1.5 | 1042 | RD50-MPW4 | 800 MeV | Low Flux High | Proton | Unknown | 20.09.2025 21:11:57 | 20.09.2025 21:12:41 | 0 | Normal | | | automatic log for run 1042
Comment:
DMA debugging |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 1
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/dma/dma_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -190
[Producer.tracker_irgendwas]
|
|
245
|
Sat Sep 20 21:19:04 2025 |
elog_producer | Caribou 1.5 | | RD50-MPW4 | 800 MeV | Low Flux High | Proton | Unknown | | | | Normal | | | DMA debugging
not waiting for IOC flag
frame rate UDP vs. DMA similar now |
|
246
|
Sat Sep 20 21:19:29 2025 |
elog_producer | Caribou 1.5 | 1043 | RD50-MPW4 | 800 MeV | Low Flux High | Proton | Unknown | 20.09.2025 21:18:09 | 20.09.2025 21:19:40 | 1 | Normal | | | automatic log for run 1043
Comment:
DMA debugging
not waiting for IOC flag
frame rate UDP vs. DMA similar now |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 1
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/dma/dma_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -190
[Producer.tracker_irgendwas]
|
|
247
|
Sat Sep 20 21:23:52 2025 |
elog_producer | Caribou 1.5 | 1044 | RD50-MPW4 | 800 MeV | Low Flux High | Proton | Unknown | 20.09.2025 21:23:44 | 20.09.2025 21:24:03 | 0 | Normal | | | automatic log for run 1044
Comment:
DMA debugging
no data |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 1
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/dma/dma_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -190
[Producer.tracker_irgendwas]
|
|
1
|
Wed Mar 12 09:29:08 2025 |
tb-crew | validating setup | | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | | | | HV | None | | | 1st test |
|
2
|
Thu Mar 13 16:29:06 2025 |
tb-crew | validating setup | 94 | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | 13.03.2025 16:27:33 | 13.03.2025 16:29:31 | 1 | HV | None | | automatic log for run 94
Comment:
tests without beam |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 0
HDMI2_clk = 0
HDMI3_clk = 0
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 6 # 0
in0_DEL = 0 # 18
in1_STR = 6 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 10 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xD
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x0 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN="/home/silicon/TJ-Monopix2/testbeam_03_2025/tlu/tlu_run$6R.raw"
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_W02R01]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W02R01_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.10.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W02R01"
chip_sn="W02R01"
online_monitor_port="5700"
[Producer.tjmonopix2_W14R18]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W14R18_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.12.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W14R18"
chip_sn="W14R18"
online_monitor_port="5500"
[Producer.HamegProducer]
hv=20
power_cycle_at_stop=1 #0=False 1=True
logging=1 #0=False 1=True
log_interval=10
logging_directory="/home/silicon/TJ-Monopix2/TJ-Monopix2-Power/Log/testbeam_prep"
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
3
|
Thu Mar 13 16:36:43 2025 |
tb-crew | validating setup | 95 | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | 13.03.2025 16:34:19 | 13.03.2025 16:37:08 | 2 | HV | None | | automatic log for run 95
Comment:
tests without beam |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 6 # 0
in0_DEL = 0 # 18
in1_STR = 6 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 10 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xD
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xFF #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x0 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN="/home/silicon/TJ-Monopix2/testbeam_03_2025/tlu/tlu_run$6R.raw"
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_W02R01]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W02R01_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.10.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W02R01"
chip_sn="W02R01"
online_monitor_port="5700"
[Producer.tjmonopix2_W14R18]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W14R18_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.12.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W14R18"
chip_sn="W14R18"
online_monitor_port="5500"
[Producer.HamegProducer]
hv=20
power_cycle_at_stop=1 #0=False 1=True
logging=1 #0=False 1=True
log_interval=10
logging_directory="/home/silicon/TJ-Monopix2/TJ-Monopix2-Power/Log/testbeam_prep"
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
4
|
Fri Mar 14 19:47:58 2025 |
mausi | validating setup | | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | | | | HV | None | | | system tests |
|
5
|
Fri Mar 14 19:50:29 2025 |
elog-producer | validating setup | 109 | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | 14.03.2025 19:49:10 | 14.03.2025 19:50:55 | 1 | HV | None | | automatic log for run 109
Comment:
system tests |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 6 # 0
in0_DEL = 0 # 18
in1_STR = 6 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 10 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x3F #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN="/home/silicon/TJ-Monopix2/testbeam_03_2025/tlu/tlu_run$6R.raw"
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_W02R01]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W02R01_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.10.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W02R01"
chip_sn="W02R01"
online_monitor_port="5500"
[Producer.tjmonopix2_W14R18]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W14R18_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.12.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W14R18"
chip_sn="W14R18"
online_monitor_port="5700"
[Producer.HamegProducer]
hv=20
power_cycle_at_stop=1 #0=False 1=True
logging=1 #0=False 1=True
log_interval=10
logging_directory="/home/silicon/TJ-Monopix2/TJ-Monopix2-Power/Log/testbeam_prep"
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
6
|
Fri Mar 14 19:57:28 2025 |
elog-producer | validating setup | 110 | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | 14.03.2025 19:51:51 | 14.03.2025 19:57:54 | 6 | HV | None | | automatic log for run 110
Comment:
bla |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 6 # 0
in0_DEL = 0 # 18
in1_STR = 6 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 10 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x3F #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN="/home/silicon/TJ-Monopix2/testbeam_03_2025/tlu/tlu_run$6R.raw"
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_W02R01]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W02R01_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.10.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W02R01"
chip_sn="W02R01"
online_monitor_port="5500"
[Producer.tjmonopix2_W14R18]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W14R18_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.12.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W14R18"
chip_sn="W14R18"
online_monitor_port="5700"
[Producer.HamegProducer]
hv=20
power_cycle_at_stop=1 #0=False 1=True
logging=1 #0=False 1=True
log_interval=10
logging_directory="/home/silicon/TJ-Monopix2/TJ-Monopix2-Power/Log/testbeam_prep"
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
7
|
Fri Mar 14 20:04:41 2025 |
elog-producer | validating setup | 111 | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | 14.03.2025 20:03:34 | 14.03.2025 20:05:07 | 1 | HV | None | | automatic log for run 111
Comment:
bla |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 6 # 0
in0_DEL = 0 # 18
in1_STR = 6 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 10 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x3F #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN="/home/silicon/TJ-Monopix2/testbeam_03_2025/tlu/tlu_run$6R.raw"
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_W02R01]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W02R01_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.10.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W02R01"
chip_sn="W02R01"
online_monitor_port="5500"
[Producer.tjmonopix2_W14R18]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W14R18_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.12.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W14R18"
chip_sn="W14R18"
online_monitor_port="5700"
[Producer.HamegProducer]
hv=20
power_cycle_at_stop=1 #0=False 1=True
logging=1 #0=False 1=True
log_interval=10
logging_directory="/home/silicon/TJ-Monopix2/TJ-Monopix2-Power/Log/testbeam_prep"
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
8
|
Fri Mar 14 20:40:06 2025 |
elog-producer | validating setup | 112 | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | 14.03.2025 20:07:47 | 14.03.2025 20:40:32 | 32 | HV | None | | automatic log for run 112
Comment:
still testing nonsense |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 6 # 0
in0_DEL = 0 # 18
in1_STR = 6 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 10 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x3F #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN="/home/silicon/TJ-Monopix2/testbeam_03_2025/tlu/tlu_run$6R.raw"
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_W02R01]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W02R01_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.10.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W02R01"
chip_sn="W02R01"
online_monitor_port="5500"
[Producer.tjmonopix2_W14R18]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W14R18_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.12.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W14R18"
chip_sn="W14R18"
online_monitor_port="5700"
[Producer.HamegProducer]
hv=20
power_cycle_at_stop=1 #0=False 1=True
logging=1 #0=False 1=True
log_interval=10
logging_directory="/home/silicon/TJ-Monopix2/TJ-Monopix2-Power/Log/testbeam_prep"
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
9
|
Fri Mar 14 21:40:34 2025 |
elog-producer | validating setup | | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | | | | HV | None | | | tracker test without beam |
|
10
|
Fri Mar 14 21:41:12 2025 |
elog-producer | validating setup | 116 | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | 14.03.2025 21:41:05 | 14.03.2025 21:41:38 | 0 | HV | None | | automatic log for run 116
Comment:
tracker test without beam |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 6 # 0
in0_DEL = 0 # 18
in1_STR = 6 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 20000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xB
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x3F #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xB #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN="/home/silicon/TJ-Monopix2/testbeam_03_2025/tlu/tlu_run$6R.raw"
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_W02R01]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W02R01_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.10.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W02R01"
chip_sn="W02R01"
online_monitor_port="5500"
[Producer.tjmonopix2_W14R18]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W14R18_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.12.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W14R18"
chip_sn="W14R18"
online_monitor_port="5700"
[Producer.HamegProducer]
hv=20
power_cycle_at_stop=1 #0=False 1=True
logging=1 #0=False 1=True
log_interval=10
logging_directory="/home/silicon/TJ-Monopix2/TJ-Monopix2-Power/Log/testbeam_prep"
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|