 Mon Jan 6 19:10:36 2014, Thomas Bergauer, common, Beam Momentum 3GeV/c, run001 to run012, , , , Unknown 
|
We have set the beam momentum to 3 GeV |
|
Tue Jan 7 09:33:51 2014, Thomas Bergauer, common, beam momentum back to 3Gev/c, run014 and later ones, , , , Unknown
|
| |
|
Thu Jan 9 14:47:21 2014, Thomas Bergauer, common, position of DESY Table, , , , , Unknown
|
BEAM mode:
- height (z): -346 (initially: -357)
- horizontal (x): -255
OFF BEAM mode (Parkposition):
- height (z): +37
- horizontal (x): -255
|
|
Mon Jan 13 12:02:40 2014, Markus Friedl, common, Kontakt, , , , , Unknown
|
Richard Thalmeier Tel. 4801
Hao Yin |
|
Sun Jan 19 18:01:46 2014, Christian Irmler, common, AIDA setup operated with TuxDAQ, , , , , Unknown
|
New SIS driver version sis1100-2.13-3 installed on DAQPC.
To install the driver call as root:
cd /lib/modules/2.6.18-371.3.1.el5/extra
/sbin/modprobe sis1100
Check if /dev/sis* are created.
Managed to run the AIDA setup with old TuxDAQ version from T. Obermayer.
Will now try to install a newer version, which also supports ADC delay scan and internal calibration. |
|
Sat Jan 4 16:30:46 2014, Markus Friedl, Infineon, cal, cal001, 83800, 04.01.2014 16:16:51, 04.01.2014 16:25:46, Good
|
HV=300V I=9.3uA (total) |
|
Mon Jan 6 16:33:13 2014, Markus Friedl, Infineon, run, run001, 200k, 06.01.2014 16:28:58, 06.01.2014 17:10:56, Good
|
HV=300V I=11.1uA
position centered horizontally (+5mm)
DESY table z=-346 x=-255
3 GeV beam momentum |
|
Mon Jan 6 17:17:47 2014, Markus Friedl, Infineon, run, run002, 200k, 06.01.2014 17:14:39, 06.01.2014 18:00:34, Good
|
HV=100V I=8.5uA
position centered horizontally (+5mm)
DESY table z=-346 x=-255
3 GeV beam momentum |
|
Mon Jan 6 18:06:16 2014, Markus Friedl, Infineon, run, run003, 200k, 06.01.2014 18:04:14, 06.01.2014 18:44:15, Good
|
HV=200V I=9.3uA
position centered horizontally (+5mm)
DESY table z=-346 x=-255
3 GeV beam momentum |
|
Mon Jan 6 18:49:00 2014, Markus Friedl, Infineon, run, run004, 200k, 06.01.2014 18:47:38, 06.01.2014 19:27:33, Good
|
HV=250V I=9.5uA
position centered horizontally (+5mm)
DESY table z=-346 x=-255
3 GeV beam momentum |
|
Mon Jan 6 20:14:21 2014, Markus Friedl, Infineon, run, run006, 200k, 06.01.2014 20:12:20, 06.01.2014 20:54:34, Good
|
HV=240V I=9.4uA
position centered horizontally (+5mm)
DESY table z=-346 x=-255
3 GeV beam momentum |
|
Mon Jan 6 20:57:38 2014, Markus Friedl, Infineon, run, run007, 200k, 06.01.2014 20:56:08, 06.01.2014 21:36:54, Good
|
HV=220V I=9.1uA
position centered horizontally (+5mm)
DESY table z=-346 x=-255
3 GeV beam momentum |
|
Mon Jan 6 21:40:29 2014, Markus Friedl, Infineon, run, run008, 200k, 06.01.2014 21:38:46, 06.01.2014 22:20:13, Good
|
HV=210V I=9.0uA
position centered horizontally (+5mm)
DESY table z=-346 x=-255
3 GeV beam momentum |
|
Mon Jan 6 22:23:39 2014, Markus Friedl, Infineon, run, run009, 200k, 06.01.2014 22:22:10, 06.01.2014 23:03:23, Good
|
HV=260V I=9.3uA
position centered horizontally (+5mm)
DESY table z=-346 x=-255
3 GeV beam momentum |
|
Mon Jan 6 23:06:51 2014, Markus Friedl, Infineon, run, run010, 200k, 06.01.2014 23:03:23, 06.01.2014 23:47:02 , Good
|
HV=270V I=9.6uA
position centered horizontally (+5mm)
DESY table z=-346 x=-255
3 GeV beam momentum |
|
Mon Jan 6 23:50:59 2014, Markus Friedl, Infineon, run, run011, 200k, 06.01.2014 23:49:09, 07.01.2014 00:30:38 , Good
|
HV=280V I=9.6uA
position centered horizontally (+5mm)
DESY table z=-346 x=-255
3 GeV beam momentum |
|
Tue Jan 7 00:36:03 2014, Markus Friedl, Infineon, run, run012, 190k, 07.01.2014 00:33:58, 07.01.2014 02:12:32 , Good
|
HV=150V I=8.0uA
position centered horizontally (+5mm)
DESY table z=-346 x=-255
3 GeV beam momentum
close to end: switched to 6GeV |
|
Tue Jan 7 02:18:26 2014, Markus Friedl, Infineon, run, run013, 215k, 07.01.2014 02:14:50, 07.01.2014 08:31:25, Crap
|
HV=150V I=7.90uA
position centered horizontally (+5mm)
DESY table z=-346 x=-255
3 GeV beam momentum
close to end: switched to 6GeV
bias voltage accidentally left at 150V instead of initially planned 290V |
|
Tue Jan 7 08:36:29 2014, Thomas Bergauer, Infineon, run, run014, 20k, 07.01.2014 08:34:06, 07.01.2014 09:05:47, Good
|
HV=290V I=9.55uA
position centered horizontally (+5mm)
DESY table z=-346 x=-255
6Gev/c,
bad strip region hardly hit |
|
Tue Jan 7 11:50:34 2014, Markus Friedl, Infineon, scan, run018x, 10k, 07.01.2014 11:xx:xx, 07.01.2014 11:xx:xx, Good
|
Delay scan with single sample
Several runs |
|