ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns), FIRRun_Cold_001

ADC shifted by 9 (4.5ns) all sensors

with room temp i2c config

Temp = room

target: -Z

ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns), FIRRun_Cold_001

ADC shifted by 5 (2.5ns) all sensors

with room temp i2c config

Temp = room

target: -Z

Note : n-side (strip nr 200 - 220 shadowhits)

ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns), FIRRun_Cold_001

ADC delay shifted by 3 (1.5ns) all sensors

with room temp i2c config

Temp = room

target: -Z

ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns), FIRRun_Cold_001

with room temp i2c config

Temp = room

target: -Z

ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns), FIRRun_Cold_001

with room temp i2c config

Temp = 0°C

target: CE

ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns), FIRRun_Cold_001

Temp = 0°C

target: CE

ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns), FIRRun_Cold_001

target: -Z

ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns), FIRRun_Cold_001

ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns)

ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns)

ADC Hot, FIRRun001, PedestalRun001

target: -Z

room temp pedrun

ADC Hot, FIRRun001, PedestalRun001

room temp pedrun

target: BW

ADC Hot, FIRRun001

room temp pedrun

FirRun 20 min after I2C

ADC delay scan at room temp and 20 min after APV I2C config.

measured values at display in the FIR_HOT cfg file.

17:06 first run 20 min after i2c config.

FIR filter and ADC delay test:
ADC delay and FIR filter with and without cooling to reproduce error detected during CERN beam test 2015.
 

Measurements wo cooling:

Measurements w cooling:

Mesurements w cooled configs:

Data of this entry is recorded in the folder: LV315kHz_Injections
Injecting noise to LV with a freq. of 314 kHz to emulate Caen PS with KenWood PS.

Run Name 315kHzKenWood_: (injecting cmc noise into p-side lv) (attachment 1)
000 ... baseline noise
001 ... 4mA
002 ... 1mA
003 ... 1mA wo Amplifier
004 ... 4mA wo Amplifier
005 ... 0.5mA wo Amplifier
006 ... 2mA wo Amplifier
007 ... 0.2mA wo Amplifier

Run Name 315kHzKenWood_Filter_BW_: (injecting cmc noise into p-side lv with filters (inductance with 470 mH x 6 ) conn. at bw) (attachment 1) (wo Amplifier)
000 ... baseline noise
001 ... 0.2mA
002 ... 0.4mA
003 ... 0.5mA
004 ... 1mA
005 ... 2mA
006 ... 4mA

Run Name 315kHzKenWood_Filer_BW_HVRET-GND:
000 ... baseline noise
001 ... 0.2mA
002 ... 0.4mA
 

Measured Primary side of caen wo load (setup attachment 2 and prelimilary res. attachment 1. )

and with load (attachment 3: Load, att. 4 corresponding circuit scheme)

Baseline noise measurements wo injection.

measure noise in both HV and LV.

wings of APV25 using cmc with 128 strip are visible wo injection. (folder CAEN_PS, run name Noise_xxx.dat).

CMC measurements wo injection:
* LV 300kHz, 1MHz + harmonics
* HV also noisy, few peak showed a induction of about 1 mA. the injected noise goese through p-side HV and returns at n-side HV - and vise versa-.

@ caen HV Ctrl (software)
always shows a current with about 0.5 mA with LV and HV switched off....

 

(TestNr: 16)

base line noise measurement are saved in SYSTEM_CHECK_AFTER_WE.
(noise wings at fw n side decreased !!!)

Measuring noise emitted by our system.
1) noise emmision at the cable from dockbox to the hybrid (fw n and p side)