#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib_base.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_hitbus_dcols =
en_sfout_dcol = 0
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-9
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 3
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
inj__u = 0
inj__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1
th__i = 3
[RD50_MPW4_Piggy]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib_piggy.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_hitbus_dcols =
en_sfout_dcol = 0
en_tb_mode = 0
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
inj_t0 = 0
matrix_config = matrix_mpw4_piggy.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 2
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 3
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
|
[RunControl]
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
ADDITIONAL_DISPLAY_NUMBERS = log,_SERVER
[LogCollector.log]
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
#PMT1_V = 0.8
#PMT2_V = 0.85
#PMT3_V = 0.8
#PMT4_V = 0.0
## TRIGGER CONFIGURATION
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00000002
trigMaskHi = 0x00000001
trigMaskLo = 0x00000000
in0_DEL = 0
in0_STR = 0x3F
in1_DEL = 0
in1_STR = 1
in2_DEL = 0
in2_STR = 0x3F
in3_DEL = 0
in3_STR = 1
in4_DEL = 0
in4_STR = 0
in5_DEL = 0
in5_STR = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = +0.3
DACThreshold1 = -0.04
DACThreshold2 = -0.04
DACThreshold3 = -1.2
DACThreshold4 = -1.2
DACThreshold5 = +0.3
trigPol=0x0
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask = 0xD
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode = 0xF1
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x0 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
[Producer.altel]
EUDAQ_DC = tel_dc
EUDAQ_ID = 1
[Producer.elog1]
files2log = "peary_config.cfg, matrix_mpw4_base.txt"
start_cmd = "./get_mpw4_configs.sh"
[Producer.keithleyPS]
voltage = -190
max_current = 50e-6
ramp_step = 5
ramp_speed = 100
[Producer.MuPix8]
#EUDAQ_DC = tel_dc
#lazyFrog = -25
#register_value = 0
ThPix = 144
[Producer.RD50_MPW4_0]
voltage_key = th
voltage_value = 1.05
register_key = vnfb
register_value = 18
[DataCollector.mpw4_dc]
DISABLE_PRINT = 1
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/external-hd/desy2410/mpw4/mpw4_run$6R$X
EUDAQ_MN = mpw4_mon
XILINX_IP = 192.168.201.1
[DataCollector.tel_dc]
DISABLE_PRINT = 1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /data1/rd50-mpw4/oct24/adenium/adenium_run$6R$X
[DataCollector.tlu_dc]
DISABLE_PRINT = 1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /data1/rd50-mpw4/oct24/tlu/tlu_run$6R$X
[Monitor.mpw4_mon]
buffer_size = 50000
update_thr = 50
|