| ID |
Date |
Author |
Subject |
Run Number |
DUT |
Wafer |
HV |
Fluence |
Resistivity |
Beam Energy |
Rate Setting |
Particle Type |
Data |
t-Start |
t-Stop |
Duration_min |
|
40
|
Wed Jul 5 12:29:07 2023 |
tb-crew | searching correlations | 643 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 05.07.2023 12:20:44 | 05.07.2023 12:24:56 | 4 |
automatic log for run 643
Comment:
running with base & piggy
Only very few pixel active |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.35
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 1 0 0 0 -1
00 01 1 0 0 0 -1
00 02 1 0 0 0 -1
00 03 1 0 0 0 -1
00 04 1 0 0 0 -1
00 05 1 0 0 0 -1
00 06 1 0 0 0 -1
00 07 1 0 0 0 -1
00 08 1 0 0 0 -1
00 09 1 0 0 0 -1
00 10 1 0 0 0 -1
00 11 1 0 0 0 -1
00 12 1 0 0 0 -1
00 13 1 0 0 0 -1
00 14 1 0 0 0 -1
00 15 1 0 0 0 -1
00 16 1 0 0 0 -1
00 17 1 0 0 0 -1
00 18 1 0 0 0 -1
00 19 1 0 0 0 -1
00 20 1 0 0 0 -1
00 21 1 0 0 0 -1
00 22 1 0 0 0 -1
00 23 1 0 0 0 -1
00 24 1 0 0 0 -1
00 25 1 0 0 0 -1
00 26 1 0 0 0 -1
00 27 1 0 0 0 -1
00 28 1 0 0 0 -1
00 29 1 0 0 0 -1
00 30 1 0 0 0 -1
00 31 1 0 0 0 -1
00 32 1 0 0 0 -1
00 33 1 0 0 0 -1
00 34 1 0 0 0 -1
00 35 1 0 0 0 -1
00 36 1 0 0 0 -1
00 37 1 0 0 0 -1
00 38 1 0 0 0 -1
00 39 1 0 0 0 -1
00 40 1 0 0 0 -1
00 41 1 0 0 0 -1
00 42 1 0 0 0 -1
00 43 1 0 0 0 -1
00 44 1 0 0 0 -1
00 45 1 0 0 0 -1
00 46 1 0 0 0 -1
00 47 1 0 0 0 -1
00 48 1 0 0 0 -1
00 49 1 0 0 0 -1
00 50 1 0 0 0 -1
00 51 1 0 0 0 -1
00 52 1 0 0 0 -1
00 53 1 0 0 0 -1
00 54 1 0 0 0 -1
00 55 1 0 0 0 -1
00 56 1 0 0 0 -1
00 57 1 0 0 0 -1
00 58 1 0 0 0 -1
00 59 1 0 0 0 -1
00 60 1 0 0 0 -1
00 61 1 0 0 0 -1
00 62 1 0 0 0 -1
00 63 1 0 0 0 -1
01 00 1 0 0 0 -1
01 01 1 0 0 0 -1
01 02 1 0 0 0 -1
01 03 1 0 0 0 -1
01 04 1 0 0 0 -1
01 05 1 0 0 0 -1
01 06 1 0 0 0 -1
01 07 1 0 0 0 -1
01 08 1 0 0 0 -1
01 09 1 0 0 0 -1
01 10 1 0 0 0 -1
01 11 1 0 0 0 -1
01 12 1 0 0 0 -1
01 13 1 0 0 0 -1
01 14 1 0 0 0 -1
01 15 1 0 0 0 -1
01 16 1 0 0 0 -1
01 17 1 0 0 0 -1
01 18 1 0 0 0 -1
01 19 1 0 0 0 -1
01 20 1 0 0 0 -1
01 21 1 0 0 0 -1
01 22 1 0 0 0 -1
01 23 1 0 0 0 -1
01 24 1 0 0 0 -1
01 25 1 0 0 0 -1
01 26 1 0 0 0 -1
01 27 1 0 0 0 -1
01 28 1 0 0 0 -1
01 29 1 0 0 0 -1
01 30 1 0 0 0 -1
01 31 1 0 0 0 -1
01 32 1 0 0 0 -1
01 33 1 0 0 0 -1
01 34 1 0 0 0 -1
01 35 1 0 0 0 -1
01 36 1 0 0 0 -1
01 37 1 0 0 0 -1
01 38 1 0 0 0 -1
01 39 1 0 0 0 -1
01 40 1 0 0 0 -1
01 41 1 0 0 0 -1
01 42 1 0 0 0 -1
01 43 1 0 0 0 -1
01 44 1 0 0 0 -1
01 45 1 0 0 0 -1
01 46 1 0 0 0 -1
01 47 1 0 0 0 -1
01 48 1 0 0 0 -1
01 49 1 0 0 0 -1
01 50 1 0 0 0 -1
01 51 1 0 0 0 -1
01 52 1 0 0 0 -1
01 53 1 0 0 0 -1
01 54 1 0 0 0 -1
01 55 1 0 0 0 -1
01 56 1 0 0 0 -1
01 57 1 0 0 0 -1
01 58 1 0 0 0 -1
01 59 1 0 0 0 -1
01 60 1 0 0 0 -1
01 61 1 0 0 0 -1
01 62 1 0 0 0 -1
01 63 1 0 0 0 -1
02 00 1 0 0 0 -1
02 01 1 0 0 0 -1
02 02 1 0 0 0 -1
02 03 1 0 0 0 -1
02 04 1 0 0 0 -1
02 05 1 0 0 0 -1
02 06 1 0 0 0 -1
02 07 1 0 0 0 -1
02 08 1 0 0 0 -1
02 09 1 0 0 0 -1
02 10 1 0 0 0 -1
02 11 1 0 0 0 -1
02 12 1 0 0 0 -1
02 13 1 0 0 0 -1
02 14 1 0 0 0 -1
02 15 1 0 0 0 -1
02 16 1 0 0 0 -1
02 17 1 0 0 0 -1
02 18 1 0 0 0 -1
02 19 1 0 0 0 -1
02 20 1 0 0 0 -1
02 21 1 0 0 0 -1
02 22 1 0 0 0 -1
02 23 1 0 0 0 -1
02 24 1 0 0 0 -1
02 25 1 0 0 0 -1
02 26 1 0 0 0 -1
02 27 1 0 0 0 -1
02 28 1 0 0 0 -1
02 29 1 0 0 0 -1
02 30 1 0 0 0 -1
02 31 1 0 0 0 -1
02 32 1 0 0 0 -1
02 33 1 0 0 0 -1
02 34 1 0 0 0 -1
02 35 1 0 0 0 -1
02 36 1 0 0 0 -1
02 37 1 0 0 0 -1
02 38 1 0 0 0 -1
02 39 1 0 0 0 -1
02 40 1 0 0 0 -1
02 41 1 0 0 0 -1
02 42 1 0 0 0 -1
02 43 1 0 0 0 -1
02 44 1 0 0 0 -1
02 45 1 0 0 0 -1
02 46 1 0 0 0 -1
02 47 1 0 0 0 -1
02 48 1 0 0 0 -1
02 49 1 0 0 0 -1
02 50 1 0 0 0 -1
02 51 1 0 0 0 -1
02 52 1 0 0 0 -1
02 53 1 0 0 0 -1
02 54 1 0 0 0 -1
02 55 1 0 0 0 -1
02 56 1 0 0 0 -1
02 57 1 0 0 0 -1
02 58 1 0 0 0 -1
02 59 1 0 0 0 -1
02 60 1 0 0 0 -1
02 61 1 0 0 0 -1
02 62 1 0 0 0 -1
02 63 1 0 0 0 -1
03 00 1 0 0 0 -1
03 01 1 0 0 0 -1
03 02 1 0 0 0 -1
03 03 1 0 0 0 -1
03 04 1 0 0 0 -1
03 05 1 0 0 0 -1
03 06 1 0 0 0 -1
03 07 1 0 0 0 -1
03 08 1 0 0 0 -1
03 09 1 0 0 0 -1
03 10 1 0 0 0 -1
03 11 1 0 0 0 -1
03 12 1 0 0 0 -1
03 13 1 0 0 0 -1
03 14 1 0 0 0 -1
03 15 1 0 0 0 -1
03 16 1 0 0 0 -1
03 17 1 0 0 0 -1
03 18 1 0 0 0 -1
03 19 1 0 0 0 -1
03 20 1 0 0 0 -1
03 21 1 0 0 0 -1
03 22 1 0 0 0 -1
03 23 1 0 0 0 -1
03 24 1 0 0 0 -1
03 25 1 0 0 0 -1
03 26 1 0 0 0 -1
03 27 1 0 0 0 -1
03 28 1 0 0 0 -1
03 29 1 0 0 0 -1
03 30 1 0 0 0 -1
03 31 1 0 0 0 -1
03 32 1 0 0 0 -1
03 33 1 0 0 0 -1
03 34 1 0 0 0 -1
03 35 1 0 0 0 -1
03 36 1 0 0 0 -1
03 37 1 0 0 0 -1
03 38 1 0 0 0 -1
03 39 1 0 0 0 -1
03 40 1 0 0 0 -1
03 41 1 0 0 0 -1
03 42 1 0 0 0 -1
03 43 1 0 0 0 -1
03 44 1 0 0 0 -1
03 45 1 0 0 0 -1
03 46 1 0 0 0 -1
03 47 1 0 0 0 -1
03 48 1 0 0 0 -1
03 49 1 0 0 0 -1
03 50 1 0 0 0 -1
03 51 1 0 0 0 -1
03 52 1 0 0 0 -1
03 53 1 0 0 0 -1
03 54 1 0 0 0 -1
03 55 1 0 0 0 -1
03 56 1 0 0 0 -1
03 57 1 0 0 0 -1
03 58 1 0 0 0 -1
03 59 1 0 0 0 -1
03 60 1 0 0 0 -1
03 61 1 0 0 0 -1
03 62 1 0 0 0 -1
03 63 1 0 0 0 -1
04 00 1 0 0 0 -1
04 01 1 0 0 0 -1
04 02 1 0 0 0 -1
04 03 1 0 0 0 -1
04 04 1 0 0 0 -1
04 05 1 0 0 0 -1
04 06 1 0 0 0 -1
04 07 1 0 0 0 -1
04 08 1 0 0 0 -1
04 09 1 0 0 0 -1
04 10 1 0 0 0 -1
04 11 1 0 0 0 -1
04 12 1 0 0 0 -1
04 13 1 0 0 0 -1
04 14 1 0 0 0 -1
04 15 1 0 0 0 -1
04 16 1 0 0 0 -1
04 17 1 0 0 0 -1
04 18 1 0 0 0 -1
04 19 1 0 0 0 -1
04 20 1 0 0 0 -1
04 21 1 0 0 0 -1
04 22 1 0 0 0 -1
04 23 1 0 0 0 -1
04 24 1 0 0 0 -1
04 25 1 0 0 0 -1
04 26 1 0 0 0 -1
04 27 1 0 0 0 -1
04 28 1 0 0 0 -1
04 29 1 0 0 0 -1
04 30 1 0 0 0 -1
04 31 1 0 0 0 -1
04 32 1 0 0 0 -1
04 33 1 0 0 0 -1
04 34 1 0 0 0 -1
04 35 1 0 0 0 -1
04 36 1 0 0 0 -1
04 37 1 0 0 0 -1
... 3774 more lines ...
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 1 0 0 0 -1
00 01 1 0 0 0 -1
00 02 1 0 0 0 -1
00 03 1 0 0 0 -1
00 04 1 0 0 0 -1
00 05 1 0 0 0 -1
00 06 1 0 0 0 -1
00 07 1 0 0 0 -1
00 08 1 0 0 0 -1
00 09 1 0 0 0 -1
00 10 1 0 0 0 -1
00 11 1 0 0 0 -1
00 12 1 0 0 0 -1
00 13 1 0 0 0 -1
00 14 1 0 0 0 -1
00 15 1 0 0 0 -1
00 16 1 0 0 0 -1
00 17 1 0 0 0 -1
00 18 1 0 0 0 -1
00 19 1 0 0 0 -1
00 20 1 0 0 0 -1
00 21 1 0 0 0 -1
00 22 1 0 0 0 -1
00 23 1 0 0 0 -1
00 24 1 0 0 0 -1
00 25 1 0 0 0 -1
00 26 1 0 0 0 -1
00 27 1 0 0 0 -1
00 28 1 0 0 0 -1
00 29 1 0 0 0 -1
00 30 1 0 0 0 -1
00 31 1 0 0 0 -1
00 32 1 0 0 0 -1
00 33 1 0 0 0 -1
00 34 1 0 0 0 -1
00 35 1 0 0 0 -1
00 36 1 0 0 0 -1
00 37 1 0 0 0 -1
00 38 1 0 0 0 -1
00 39 1 0 0 0 -1
00 40 1 0 0 0 -1
00 41 1 0 0 0 -1
00 42 1 0 0 0 -1
00 43 1 0 0 0 -1
00 44 1 0 0 0 -1
00 45 1 0 0 0 -1
00 46 1 0 0 0 -1
00 47 1 0 0 0 -1
00 48 1 0 0 0 -1
00 49 1 0 0 0 -1
00 50 1 0 0 0 -1
00 51 1 0 0 0 -1
00 52 1 0 0 0 -1
00 53 1 0 0 0 -1
00 54 1 0 0 0 -1
00 55 1 0 0 0 -1
00 56 1 0 0 0 -1
00 57 1 0 0 0 -1
00 58 1 0 0 0 -1
00 59 1 0 0 0 -1
00 60 1 0 0 0 -1
00 61 1 0 0 0 -1
00 62 1 0 0 0 -1
00 63 1 0 0 0 -1
01 00 1 0 0 0 -1
01 01 1 0 0 0 -1
01 02 1 0 0 0 -1
01 03 1 0 0 0 -1
01 04 1 0 0 0 -1
01 05 1 0 0 0 -1
01 06 1 0 0 0 -1
01 07 1 0 0 0 -1
01 08 1 0 0 0 -1
01 09 1 0 0 0 -1
01 10 1 0 0 0 -1
01 11 1 0 0 0 -1
01 12 1 0 0 0 -1
01 13 1 0 0 0 -1
01 14 1 0 0 0 -1
01 15 1 0 0 0 -1
01 16 1 0 0 0 -1
01 17 1 0 0 0 -1
01 18 1 0 0 0 -1
01 19 1 0 0 0 -1
01 20 1 0 0 0 -1
01 21 1 0 0 0 -1
01 22 1 0 0 0 -1
01 23 1 0 0 0 -1
01 24 1 0 0 0 -1
01 25 1 0 0 0 -1
01 26 1 0 0 0 -1
01 27 1 0 0 0 -1
01 28 1 0 0 0 -1
01 29 1 0 0 0 -1
01 30 1 0 0 0 -1
01 31 1 0 0 0 -1
01 32 1 0 0 0 -1
01 33 1 0 0 0 -1
01 34 1 0 0 0 -1
01 35 1 0 0 0 -1
01 36 1 0 0 0 -1
01 37 1 0 0 0 -1
01 38 1 0 0 0 -1
01 39 1 0 0 0 -1
01 40 1 0 0 0 -1
01 41 1 0 0 0 -1
01 42 1 0 0 0 -1
01 43 1 0 0 0 -1
01 44 1 0 0 0 -1
01 45 1 0 0 0 -1
01 46 1 0 0 0 -1
01 47 1 0 0 0 -1
01 48 1 0 0 0 -1
01 49 1 0 0 0 -1
01 50 1 0 0 0 -1
01 51 1 0 0 0 -1
01 52 1 0 0 0 -1
01 53 1 0 0 0 -1
01 54 1 0 0 0 -1
01 55 1 0 0 0 -1
01 56 1 0 0 0 -1
01 57 1 0 0 0 -1
01 58 1 0 0 0 -1
01 59 1 0 0 0 -1
01 60 1 0 0 0 -1
01 61 1 0 0 0 -1
01 62 1 0 0 0 -1
01 63 1 0 0 0 -1
02 00 1 0 0 0 -1
02 01 1 0 0 0 -1
02 02 1 0 0 0 -1
02 03 1 0 0 0 -1
02 04 1 0 0 0 -1
02 05 1 0 0 0 -1
02 06 1 0 0 0 -1
02 07 1 0 0 0 -1
02 08 1 0 0 0 -1
02 09 1 0 0 0 -1
02 10 1 0 0 0 -1
02 11 1 0 0 0 -1
02 12 1 0 0 0 -1
02 13 1 0 0 0 -1
02 14 1 0 0 0 -1
02 15 1 0 0 0 -1
02 16 1 0 0 0 -1
02 17 1 0 0 0 -1
02 18 1 0 0 0 -1
02 19 1 0 0 0 -1
02 20 1 0 0 0 -1
02 21 1 0 0 0 -1
02 22 1 0 0 0 -1
02 23 1 0 0 0 -1
02 24 1 0 0 0 -1
02 25 1 0 0 0 -1
02 26 1 0 0 0 -1
02 27 1 0 0 0 -1
02 28 1 0 0 0 -1
02 29 1 0 0 0 -1
02 30 1 0 0 0 -1
02 31 1 0 0 0 -1
02 32 1 0 0 0 -1
02 33 1 0 0 0 -1
02 34 1 0 0 0 -1
02 35 1 0 0 0 -1
02 36 1 0 0 0 -1
02 37 1 0 0 0 -1
02 38 1 0 0 0 -1
02 39 1 0 0 0 -1
02 40 1 0 0 0 -1
02 41 1 0 0 0 -1
02 42 1 0 0 0 -1
02 43 1 0 0 0 -1
02 44 1 0 0 0 -1
02 45 1 0 0 0 -1
02 46 1 0 0 0 -1
02 47 1 0 0 0 -1
02 48 1 0 0 0 -1
02 49 1 0 0 0 -1
02 50 1 0 0 0 -1
02 51 1 0 0 0 -1
02 52 1 0 0 0 -1
02 53 1 0 0 0 -1
02 54 1 0 0 0 -1
02 55 1 0 0 0 -1
02 56 1 0 0 0 -1
02 57 1 0 0 0 -1
02 58 1 0 0 0 -1
02 59 1 0 0 0 -1
02 60 1 0 0 0 -1
02 61 1 0 0 0 -1
02 62 1 0 0 0 -1
02 63 1 0 0 0 -1
03 00 1 0 0 0 -1
03 01 1 0 0 0 -1
03 02 1 0 0 0 -1
03 03 1 0 0 0 -1
03 04 1 0 0 0 -1
03 05 1 0 0 0 -1
03 06 1 0 0 0 -1
03 07 1 0 0 0 -1
03 08 1 0 0 0 -1
03 09 1 0 0 0 -1
03 10 1 0 0 0 -1
03 11 1 0 0 0 -1
03 12 1 0 0 0 -1
03 13 1 0 0 0 -1
03 14 1 0 0 0 -1
03 15 1 0 0 0 -1
03 16 1 0 0 0 -1
03 17 1 0 0 0 -1
03 18 1 0 0 0 -1
03 19 1 0 0 0 -1
03 20 1 0 0 0 -1
03 21 1 0 0 0 -1
03 22 1 0 0 0 -1
03 23 1 0 0 0 -1
03 24 1 0 0 0 -1
03 25 1 0 0 0 -1
03 26 1 0 0 0 -1
03 27 1 0 0 0 -1
03 28 1 0 0 0 -1
03 29 1 0 0 0 -1
03 30 1 0 0 0 -1
03 31 1 0 0 0 -1
03 32 1 0 0 0 -1
03 33 1 0 0 0 -1
03 34 1 0 0 0 -1
03 35 1 0 0 0 -1
03 36 1 0 0 0 -1
03 37 1 0 0 0 -1
03 38 1 0 0 0 -1
03 39 1 0 0 0 -1
03 40 1 0 0 0 -1
03 41 1 0 0 0 -1
03 42 1 0 0 0 -1
03 43 1 0 0 0 -1
03 44 1 0 0 0 -1
03 45 1 0 0 0 -1
03 46 1 0 0 0 -1
03 47 1 0 0 0 -1
03 48 1 0 0 0 -1
03 49 1 0 0 0 -1
03 50 1 0 0 0 -1
03 51 1 0 0 0 -1
03 52 1 0 0 0 -1
03 53 1 0 0 0 -1
03 54 1 0 0 0 -1
03 55 1 0 0 0 -1
03 56 1 0 0 0 -1
03 57 1 0 0 0 -1
03 58 1 0 0 0 -1
03 59 1 0 0 0 -1
03 60 1 0 0 0 -1
03 61 1 0 0 0 -1
03 62 1 0 0 0 -1
03 63 1 0 0 0 -1
04 00 1 0 0 0 -1
04 01 1 0 0 0 -1
04 02 1 0 0 0 -1
04 03 1 0 0 0 -1
04 04 1 0 0 0 -1
04 05 1 0 0 0 -1
04 06 1 0 0 0 -1
04 07 1 0 0 0 -1
04 08 1 0 0 0 -1
04 09 1 0 0 0 -1
04 10 1 0 0 0 -1
04 11 1 0 0 0 -1
04 12 1 0 0 0 -1
04 13 1 0 0 0 -1
04 14 1 0 0 0 -1
04 15 1 0 0 0 -1
04 16 1 0 0 0 -1
04 17 1 0 0 0 -1
04 18 1 0 0 0 -1
04 19 1 0 0 0 -1
04 20 1 0 0 0 -1
04 21 1 0 0 0 -1
04 22 1 0 0 0 -1
04 23 1 0 0 0 -1
04 24 1 0 0 0 -1
04 25 1 0 0 0 -1
04 26 1 0 0 0 -1
04 27 1 0 0 0 -1
04 28 1 0 0 0 -1
04 29 1 0 0 0 -1
04 30 1 0 0 0 -1
04 31 1 0 0 0 -1
04 32 1 0 0 0 -1
04 33 1 0 0 0 -1
04 34 1 0 0 0 -1
04 35 1 0 0 0 -1
04 36 1 0 0 0 -1
04 37 1 0 0 0 -1
... 3774 more lines ...
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/run$6R_mpw3$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
#NF_THR30
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/04_HV_THR22/20230705_104444_threshold_scan_interpreted.h5
#MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 480
STOP_COLUMN = 492
WAIT_FOR_FPGA = 1
CONFIG_ID = 9
ELOG_CATEGORY = Beam # Debug, Beam, VoltageScan, Scan
COMMENT_IN_CONF = "Comment here"
ELOG_OUTPUT_PATH = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs"
[Producer.hameg]
HV = 10
#BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
39
|
Wed Jul 5 12:24:26 2023 |
tb-crew | searching correlations | 642 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 05.07.2023 12:04:35 | 05.07.2023 12:20:16 | 15 |
automatic log for run 642
Comment:
running with base & piggy
Only very few pixel active |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.35
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 1 0 0 0 -1
00 01 1 0 0 0 -1
00 02 1 0 0 0 -1
00 03 1 0 0 0 -1
00 04 1 0 0 0 -1
00 05 1 0 0 0 -1
00 06 1 0 0 0 -1
00 07 1 0 0 0 -1
00 08 1 0 0 0 -1
00 09 1 0 0 0 -1
00 10 1 0 0 0 -1
00 11 1 0 0 0 -1
00 12 1 0 0 0 -1
00 13 1 0 0 0 -1
00 14 1 0 0 0 -1
00 15 1 0 0 0 -1
00 16 1 0 0 0 -1
00 17 1 0 0 0 -1
00 18 1 0 0 0 -1
00 19 1 0 0 0 -1
00 20 1 0 0 0 -1
00 21 1 0 0 0 -1
00 22 1 0 0 0 -1
00 23 1 0 0 0 -1
00 24 1 0 0 0 -1
00 25 1 0 0 0 -1
00 26 1 0 0 0 -1
00 27 1 0 0 0 -1
00 28 1 0 0 0 -1
00 29 1 0 0 0 -1
00 30 1 0 0 0 -1
00 31 1 0 0 0 -1
00 32 1 0 0 0 -1
00 33 1 0 0 0 -1
00 34 1 0 0 0 -1
00 35 1 0 0 0 -1
00 36 1 0 0 0 -1
00 37 1 0 0 0 -1
00 38 1 0 0 0 -1
00 39 1 0 0 0 -1
00 40 1 0 0 0 -1
00 41 1 0 0 0 -1
00 42 1 0 0 0 -1
00 43 1 0 0 0 -1
00 44 1 0 0 0 -1
00 45 1 0 0 0 -1
00 46 1 0 0 0 -1
00 47 1 0 0 0 -1
00 48 1 0 0 0 -1
00 49 1 0 0 0 -1
00 50 1 0 0 0 -1
00 51 1 0 0 0 -1
00 52 1 0 0 0 -1
00 53 1 0 0 0 -1
00 54 1 0 0 0 -1
00 55 1 0 0 0 -1
00 56 1 0 0 0 -1
00 57 1 0 0 0 -1
00 58 1 0 0 0 -1
00 59 1 0 0 0 -1
00 60 1 0 0 0 -1
00 61 1 0 0 0 -1
00 62 1 0 0 0 -1
00 63 1 0 0 0 -1
01 00 1 0 0 0 -1
01 01 1 0 0 0 -1
01 02 1 0 0 0 -1
01 03 1 0 0 0 -1
01 04 1 0 0 0 -1
01 05 1 0 0 0 -1
01 06 1 0 0 0 -1
01 07 1 0 0 0 -1
01 08 1 0 0 0 -1
01 09 1 0 0 0 -1
01 10 1 0 0 0 -1
01 11 1 0 0 0 -1
01 12 1 0 0 0 -1
01 13 1 0 0 0 -1
01 14 1 0 0 0 -1
01 15 1 0 0 0 -1
01 16 1 0 0 0 -1
01 17 1 0 0 0 -1
01 18 1 0 0 0 -1
01 19 1 0 0 0 -1
01 20 1 0 0 0 -1
01 21 1 0 0 0 -1
01 22 1 0 0 0 -1
01 23 1 0 0 0 -1
01 24 1 0 0 0 -1
01 25 1 0 0 0 -1
01 26 1 0 0 0 -1
01 27 1 0 0 0 -1
01 28 1 0 0 0 -1
01 29 1 0 0 0 -1
01 30 1 0 0 0 -1
01 31 1 0 0 0 -1
01 32 1 0 0 0 -1
01 33 1 0 0 0 -1
01 34 1 0 0 0 -1
01 35 1 0 0 0 -1
01 36 1 0 0 0 -1
01 37 1 0 0 0 -1
01 38 1 0 0 0 -1
01 39 1 0 0 0 -1
01 40 1 0 0 0 -1
01 41 1 0 0 0 -1
01 42 1 0 0 0 -1
01 43 1 0 0 0 -1
01 44 1 0 0 0 -1
01 45 1 0 0 0 -1
01 46 1 0 0 0 -1
01 47 1 0 0 0 -1
01 48 1 0 0 0 -1
01 49 1 0 0 0 -1
01 50 1 0 0 0 -1
01 51 1 0 0 0 -1
01 52 1 0 0 0 -1
01 53 1 0 0 0 -1
01 54 1 0 0 0 -1
01 55 1 0 0 0 -1
01 56 1 0 0 0 -1
01 57 1 0 0 0 -1
01 58 1 0 0 0 -1
01 59 1 0 0 0 -1
01 60 1 0 0 0 -1
01 61 1 0 0 0 -1
01 62 1 0 0 0 -1
01 63 1 0 0 0 -1
02 00 1 0 0 0 -1
02 01 1 0 0 0 -1
02 02 1 0 0 0 -1
02 03 1 0 0 0 -1
02 04 1 0 0 0 -1
02 05 1 0 0 0 -1
02 06 1 0 0 0 -1
02 07 1 0 0 0 -1
02 08 1 0 0 0 -1
02 09 1 0 0 0 -1
02 10 1 0 0 0 -1
02 11 1 0 0 0 -1
02 12 1 0 0 0 -1
02 13 1 0 0 0 -1
02 14 1 0 0 0 -1
02 15 1 0 0 0 -1
02 16 1 0 0 0 -1
02 17 1 0 0 0 -1
02 18 1 0 0 0 -1
02 19 1 0 0 0 -1
02 20 1 0 0 0 -1
02 21 1 0 0 0 -1
02 22 1 0 0 0 -1
02 23 1 0 0 0 -1
02 24 1 0 0 0 -1
02 25 1 0 0 0 -1
02 26 1 0 0 0 -1
02 27 1 0 0 0 -1
02 28 1 0 0 0 -1
02 29 1 0 0 0 -1
02 30 1 0 0 0 -1
02 31 1 0 0 0 -1
02 32 1 0 0 0 -1
02 33 1 0 0 0 -1
02 34 1 0 0 0 -1
02 35 1 0 0 0 -1
02 36 1 0 0 0 -1
02 37 1 0 0 0 -1
02 38 1 0 0 0 -1
02 39 1 0 0 0 -1
02 40 1 0 0 0 -1
02 41 1 0 0 0 -1
02 42 1 0 0 0 -1
02 43 1 0 0 0 -1
02 44 1 0 0 0 -1
02 45 1 0 0 0 -1
02 46 1 0 0 0 -1
02 47 1 0 0 0 -1
02 48 1 0 0 0 -1
02 49 1 0 0 0 -1
02 50 1 0 0 0 -1
02 51 1 0 0 0 -1
02 52 1 0 0 0 -1
02 53 1 0 0 0 -1
02 54 1 0 0 0 -1
02 55 1 0 0 0 -1
02 56 1 0 0 0 -1
02 57 1 0 0 0 -1
02 58 1 0 0 0 -1
02 59 1 0 0 0 -1
02 60 1 0 0 0 -1
02 61 1 0 0 0 -1
02 62 1 0 0 0 -1
02 63 1 0 0 0 -1
03 00 1 0 0 0 -1
03 01 1 0 0 0 -1
03 02 1 0 0 0 -1
03 03 1 0 0 0 -1
03 04 1 0 0 0 -1
03 05 1 0 0 0 -1
03 06 1 0 0 0 -1
03 07 1 0 0 0 -1
03 08 1 0 0 0 -1
03 09 1 0 0 0 -1
03 10 1 0 0 0 -1
03 11 1 0 0 0 -1
03 12 1 0 0 0 -1
03 13 1 0 0 0 -1
03 14 1 0 0 0 -1
03 15 1 0 0 0 -1
03 16 1 0 0 0 -1
03 17 1 0 0 0 -1
03 18 1 0 0 0 -1
03 19 1 0 0 0 -1
03 20 1 0 0 0 -1
03 21 1 0 0 0 -1
03 22 1 0 0 0 -1
03 23 1 0 0 0 -1
03 24 1 0 0 0 -1
03 25 1 0 0 0 -1
03 26 1 0 0 0 -1
03 27 1 0 0 0 -1
03 28 1 0 0 0 -1
03 29 1 0 0 0 -1
03 30 1 0 0 0 -1
03 31 1 0 0 0 -1
03 32 1 0 0 0 -1
03 33 1 0 0 0 -1
03 34 1 0 0 0 -1
03 35 1 0 0 0 -1
03 36 1 0 0 0 -1
03 37 1 0 0 0 -1
03 38 1 0 0 0 -1
03 39 1 0 0 0 -1
03 40 1 0 0 0 -1
03 41 1 0 0 0 -1
03 42 1 0 0 0 -1
03 43 1 0 0 0 -1
03 44 1 0 0 0 -1
03 45 1 0 0 0 -1
03 46 1 0 0 0 -1
03 47 1 0 0 0 -1
03 48 1 0 0 0 -1
03 49 1 0 0 0 -1
03 50 1 0 0 0 -1
03 51 1 0 0 0 -1
03 52 1 0 0 0 -1
03 53 1 0 0 0 -1
03 54 1 0 0 0 -1
03 55 1 0 0 0 -1
03 56 1 0 0 0 -1
03 57 1 0 0 0 -1
03 58 1 0 0 0 -1
03 59 1 0 0 0 -1
03 60 1 0 0 0 -1
03 61 1 0 0 0 -1
03 62 1 0 0 0 -1
03 63 1 0 0 0 -1
04 00 1 0 0 0 -1
04 01 1 0 0 0 -1
04 02 1 0 0 0 -1
04 03 1 0 0 0 -1
04 04 1 0 0 0 -1
04 05 1 0 0 0 -1
04 06 1 0 0 0 -1
04 07 1 0 0 0 -1
04 08 1 0 0 0 -1
04 09 1 0 0 0 -1
04 10 1 0 0 0 -1
04 11 1 0 0 0 -1
04 12 1 0 0 0 -1
04 13 1 0 0 0 -1
04 14 1 0 0 0 -1
04 15 1 0 0 0 -1
04 16 1 0 0 0 -1
04 17 1 0 0 0 -1
04 18 1 0 0 0 -1
04 19 1 0 0 0 -1
04 20 1 0 0 0 -1
04 21 1 0 0 0 -1
04 22 1 0 0 0 -1
04 23 1 0 0 0 -1
04 24 1 0 0 0 -1
04 25 1 0 0 0 -1
04 26 1 0 0 0 -1
04 27 1 0 0 0 -1
04 28 1 0 0 0 -1
04 29 1 0 0 0 -1
04 30 1 0 0 0 -1
04 31 1 0 0 0 -1
04 32 1 0 0 0 -1
04 33 1 0 0 0 -1
04 34 1 0 0 0 -1
04 35 1 0 0 0 -1
04 36 1 0 0 0 -1
04 37 1 0 0 0 -1
... 3774 more lines ...
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 1 0 0 0 -1
00 01 1 0 0 0 -1
00 02 1 0 0 0 -1
00 03 1 0 0 0 -1
00 04 1 0 0 0 -1
00 05 1 0 0 0 -1
00 06 1 0 0 0 -1
00 07 1 0 0 0 -1
00 08 1 0 0 0 -1
00 09 1 0 0 0 -1
00 10 1 0 0 0 -1
00 11 1 0 0 0 -1
00 12 1 0 0 0 -1
00 13 1 0 0 0 -1
00 14 1 0 0 0 -1
00 15 1 0 0 0 -1
00 16 1 0 0 0 -1
00 17 1 0 0 0 -1
00 18 1 0 0 0 -1
00 19 1 0 0 0 -1
00 20 1 0 0 0 -1
00 21 1 0 0 0 -1
00 22 1 0 0 0 -1
00 23 1 0 0 0 -1
00 24 1 0 0 0 -1
00 25 1 0 0 0 -1
00 26 1 0 0 0 -1
00 27 1 0 0 0 -1
00 28 1 0 0 0 -1
00 29 1 0 0 0 -1
00 30 1 0 0 0 -1
00 31 1 0 0 0 -1
00 32 1 0 0 0 -1
00 33 1 0 0 0 -1
00 34 1 0 0 0 -1
00 35 1 0 0 0 -1
00 36 1 0 0 0 -1
00 37 1 0 0 0 -1
00 38 1 0 0 0 -1
00 39 1 0 0 0 -1
00 40 1 0 0 0 -1
00 41 1 0 0 0 -1
00 42 1 0 0 0 -1
00 43 1 0 0 0 -1
00 44 1 0 0 0 -1
00 45 1 0 0 0 -1
00 46 1 0 0 0 -1
00 47 1 0 0 0 -1
00 48 1 0 0 0 -1
00 49 1 0 0 0 -1
00 50 1 0 0 0 -1
00 51 1 0 0 0 -1
00 52 1 0 0 0 -1
00 53 1 0 0 0 -1
00 54 1 0 0 0 -1
00 55 1 0 0 0 -1
00 56 1 0 0 0 -1
00 57 1 0 0 0 -1
00 58 1 0 0 0 -1
00 59 1 0 0 0 -1
00 60 1 0 0 0 -1
00 61 1 0 0 0 -1
00 62 1 0 0 0 -1
00 63 1 0 0 0 -1
01 00 1 0 0 0 -1
01 01 1 0 0 0 -1
01 02 1 0 0 0 -1
01 03 1 0 0 0 -1
01 04 1 0 0 0 -1
01 05 1 0 0 0 -1
01 06 1 0 0 0 -1
01 07 1 0 0 0 -1
01 08 1 0 0 0 -1
01 09 1 0 0 0 -1
01 10 1 0 0 0 -1
01 11 1 0 0 0 -1
01 12 1 0 0 0 -1
01 13 1 0 0 0 -1
01 14 1 0 0 0 -1
01 15 1 0 0 0 -1
01 16 1 0 0 0 -1
01 17 1 0 0 0 -1
01 18 1 0 0 0 -1
01 19 1 0 0 0 -1
01 20 1 0 0 0 -1
01 21 1 0 0 0 -1
01 22 1 0 0 0 -1
01 23 1 0 0 0 -1
01 24 1 0 0 0 -1
01 25 1 0 0 0 -1
01 26 1 0 0 0 -1
01 27 1 0 0 0 -1
01 28 1 0 0 0 -1
01 29 1 0 0 0 -1
01 30 1 0 0 0 -1
01 31 1 0 0 0 -1
01 32 1 0 0 0 -1
01 33 1 0 0 0 -1
01 34 1 0 0 0 -1
01 35 1 0 0 0 -1
01 36 1 0 0 0 -1
01 37 1 0 0 0 -1
01 38 1 0 0 0 -1
01 39 1 0 0 0 -1
01 40 1 0 0 0 -1
01 41 1 0 0 0 -1
01 42 1 0 0 0 -1
01 43 1 0 0 0 -1
01 44 1 0 0 0 -1
01 45 1 0 0 0 -1
01 46 1 0 0 0 -1
01 47 1 0 0 0 -1
01 48 1 0 0 0 -1
01 49 1 0 0 0 -1
01 50 1 0 0 0 -1
01 51 1 0 0 0 -1
01 52 1 0 0 0 -1
01 53 1 0 0 0 -1
01 54 1 0 0 0 -1
01 55 1 0 0 0 -1
01 56 1 0 0 0 -1
01 57 1 0 0 0 -1
01 58 1 0 0 0 -1
01 59 1 0 0 0 -1
01 60 1 0 0 0 -1
01 61 1 0 0 0 -1
01 62 1 0 0 0 -1
01 63 1 0 0 0 -1
02 00 1 0 0 0 -1
02 01 1 0 0 0 -1
02 02 1 0 0 0 -1
02 03 1 0 0 0 -1
02 04 1 0 0 0 -1
02 05 1 0 0 0 -1
02 06 1 0 0 0 -1
02 07 1 0 0 0 -1
02 08 1 0 0 0 -1
02 09 1 0 0 0 -1
02 10 1 0 0 0 -1
02 11 1 0 0 0 -1
02 12 1 0 0 0 -1
02 13 1 0 0 0 -1
02 14 1 0 0 0 -1
02 15 1 0 0 0 -1
02 16 1 0 0 0 -1
02 17 1 0 0 0 -1
02 18 1 0 0 0 -1
02 19 1 0 0 0 -1
02 20 1 0 0 0 -1
02 21 1 0 0 0 -1
02 22 1 0 0 0 -1
02 23 1 0 0 0 -1
02 24 1 0 0 0 -1
02 25 1 0 0 0 -1
02 26 1 0 0 0 -1
02 27 1 0 0 0 -1
02 28 1 0 0 0 -1
02 29 1 0 0 0 -1
02 30 1 0 0 0 -1
02 31 1 0 0 0 -1
02 32 1 0 0 0 -1
02 33 1 0 0 0 -1
02 34 1 0 0 0 -1
02 35 1 0 0 0 -1
02 36 1 0 0 0 -1
02 37 1 0 0 0 -1
02 38 1 0 0 0 -1
02 39 1 0 0 0 -1
02 40 1 0 0 0 -1
02 41 1 0 0 0 -1
02 42 1 0 0 0 -1
02 43 1 0 0 0 -1
02 44 1 0 0 0 -1
02 45 1 0 0 0 -1
02 46 1 0 0 0 -1
02 47 1 0 0 0 -1
02 48 1 0 0 0 -1
02 49 1 0 0 0 -1
02 50 1 0 0 0 -1
02 51 1 0 0 0 -1
02 52 1 0 0 0 -1
02 53 1 0 0 0 -1
02 54 1 0 0 0 -1
02 55 1 0 0 0 -1
02 56 1 0 0 0 -1
02 57 1 0 0 0 -1
02 58 1 0 0 0 -1
02 59 1 0 0 0 -1
02 60 1 0 0 0 -1
02 61 1 0 0 0 -1
02 62 1 0 0 0 -1
02 63 1 0 0 0 -1
03 00 1 0 0 0 -1
03 01 1 0 0 0 -1
03 02 1 0 0 0 -1
03 03 1 0 0 0 -1
03 04 1 0 0 0 -1
03 05 1 0 0 0 -1
03 06 1 0 0 0 -1
03 07 1 0 0 0 -1
03 08 1 0 0 0 -1
03 09 1 0 0 0 -1
03 10 1 0 0 0 -1
03 11 1 0 0 0 -1
03 12 1 0 0 0 -1
03 13 1 0 0 0 -1
03 14 1 0 0 0 -1
03 15 1 0 0 0 -1
03 16 1 0 0 0 -1
03 17 1 0 0 0 -1
03 18 1 0 0 0 -1
03 19 1 0 0 0 -1
03 20 1 0 0 0 -1
03 21 1 0 0 0 -1
03 22 1 0 0 0 -1
03 23 1 0 0 0 -1
03 24 1 0 0 0 -1
03 25 1 0 0 0 -1
03 26 1 0 0 0 -1
03 27 1 0 0 0 -1
03 28 1 0 0 0 -1
03 29 1 0 0 0 -1
03 30 1 0 0 0 -1
03 31 1 0 0 0 -1
03 32 1 0 0 0 -1
03 33 1 0 0 0 -1
03 34 1 0 0 0 -1
03 35 1 0 0 0 -1
03 36 1 0 0 0 -1
03 37 1 0 0 0 -1
03 38 1 0 0 0 -1
03 39 1 0 0 0 -1
03 40 1 0 0 0 -1
03 41 1 0 0 0 -1
03 42 1 0 0 0 -1
03 43 1 0 0 0 -1
03 44 1 0 0 0 -1
03 45 1 0 0 0 -1
03 46 1 0 0 0 -1
03 47 1 0 0 0 -1
03 48 1 0 0 0 -1
03 49 1 0 0 0 -1
03 50 1 0 0 0 -1
03 51 1 0 0 0 -1
03 52 1 0 0 0 -1
03 53 1 0 0 0 -1
03 54 1 0 0 0 -1
03 55 1 0 0 0 -1
03 56 1 0 0 0 -1
03 57 1 0 0 0 -1
03 58 1 0 0 0 -1
03 59 1 0 0 0 -1
03 60 1 0 0 0 -1
03 61 1 0 0 0 -1
03 62 1 0 0 0 -1
03 63 1 0 0 0 -1
04 00 1 0 0 0 -1
04 01 1 0 0 0 -1
04 02 1 0 0 0 -1
04 03 1 0 0 0 -1
04 04 1 0 0 0 -1
04 05 1 0 0 0 -1
04 06 1 0 0 0 -1
04 07 1 0 0 0 -1
04 08 1 0 0 0 -1
04 09 1 0 0 0 -1
04 10 1 0 0 0 -1
04 11 1 0 0 0 -1
04 12 1 0 0 0 -1
04 13 1 0 0 0 -1
04 14 1 0 0 0 -1
04 15 1 0 0 0 -1
04 16 1 0 0 0 -1
04 17 1 0 0 0 -1
04 18 1 0 0 0 -1
04 19 1 0 0 0 -1
04 20 1 0 0 0 -1
04 21 1 0 0 0 -1
04 22 1 0 0 0 -1
04 23 1 0 0 0 -1
04 24 1 0 0 0 -1
04 25 1 0 0 0 -1
04 26 1 0 0 0 -1
04 27 1 0 0 0 -1
04 28 1 0 0 0 -1
04 29 1 0 0 0 -1
04 30 1 0 0 0 -1
04 31 1 0 0 0 -1
04 32 1 0 0 0 -1
04 33 1 0 0 0 -1
04 34 1 0 0 0 -1
04 35 1 0 0 0 -1
04 36 1 0 0 0 -1
04 37 1 0 0 0 -1
... 3774 more lines ...
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/run$6R_mpw3$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
#NF_THR30
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/04_HV_THR22/20230705_104444_threshold_scan_interpreted.h5
#MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 480
STOP_COLUMN = 492
WAIT_FOR_FPGA = 1
CONFIG_ID = 9
ELOG_CATEGORY = Beam # Debug, Beam, VoltageScan, Scan
COMMENT_IN_CONF = "Comment here"
ELOG_OUTPUT_PATH = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs"
[Producer.hameg]
HV = 10
#BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
38
|
Wed Jul 5 12:02:14 2023 |
tb-crew | searching correlations | 641 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 05.07.2023 11:48:16 | 05.07.2023 11:58:04 | 9 |
automatic log for run 641
Comment:
running with base & piggy
Only very few pixel active |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.35
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 1 0 0 0 -1
00 01 1 0 0 0 -1
00 02 1 0 0 0 -1
00 03 1 0 0 0 -1
00 04 1 0 0 0 -1
00 05 1 0 0 0 -1
00 06 1 0 0 0 -1
00 07 1 0 0 0 -1
00 08 1 0 0 0 -1
00 09 1 0 0 0 -1
00 10 1 0 0 0 -1
00 11 1 0 0 0 -1
00 12 1 0 0 0 -1
00 13 1 0 0 0 -1
00 14 1 0 0 0 -1
00 15 1 0 0 0 -1
00 16 1 0 0 0 -1
00 17 1 0 0 0 -1
00 18 1 0 0 0 -1
00 19 1 0 0 0 -1
00 20 1 0 0 0 -1
00 21 1 0 0 0 -1
00 22 1 0 0 0 -1
00 23 1 0 0 0 -1
00 24 1 0 0 0 -1
00 25 1 0 0 0 -1
00 26 1 0 0 0 -1
00 27 1 0 0 0 -1
00 28 1 0 0 0 -1
00 29 1 0 0 0 -1
00 30 1 0 0 0 -1
00 31 1 0 0 0 -1
00 32 1 0 0 0 -1
00 33 1 0 0 0 -1
00 34 1 0 0 0 -1
00 35 1 0 0 0 -1
00 36 1 0 0 0 -1
00 37 1 0 0 0 -1
00 38 1 0 0 0 -1
00 39 1 0 0 0 -1
00 40 1 0 0 0 -1
00 41 1 0 0 0 -1
00 42 1 0 0 0 -1
00 43 1 0 0 0 -1
00 44 1 0 0 0 -1
00 45 1 0 0 0 -1
00 46 1 0 0 0 -1
00 47 1 0 0 0 -1
00 48 1 0 0 0 -1
00 49 1 0 0 0 -1
00 50 1 0 0 0 -1
00 51 1 0 0 0 -1
00 52 1 0 0 0 -1
00 53 1 0 0 0 -1
00 54 1 0 0 0 -1
00 55 1 0 0 0 -1
00 56 1 0 0 0 -1
00 57 1 0 0 0 -1
00 58 1 0 0 0 -1
00 59 1 0 0 0 -1
00 60 1 0 0 0 -1
00 61 1 0 0 0 -1
00 62 1 0 0 0 -1
00 63 1 0 0 0 -1
01 00 1 0 0 0 -1
01 01 1 0 0 0 -1
01 02 1 0 0 0 -1
01 03 1 0 0 0 -1
01 04 1 0 0 0 -1
01 05 1 0 0 0 -1
01 06 1 0 0 0 -1
01 07 1 0 0 0 -1
01 08 1 0 0 0 -1
01 09 1 0 0 0 -1
01 10 1 0 0 0 -1
01 11 1 0 0 0 -1
01 12 1 0 0 0 -1
01 13 1 0 0 0 -1
01 14 1 0 0 0 -1
01 15 1 0 0 0 -1
01 16 1 0 0 0 -1
01 17 1 0 0 0 -1
01 18 1 0 0 0 -1
01 19 1 0 0 0 -1
01 20 1 0 0 0 -1
01 21 1 0 0 0 -1
01 22 1 0 0 0 -1
01 23 1 0 0 0 -1
01 24 1 0 0 0 -1
01 25 1 0 0 0 -1
01 26 1 0 0 0 -1
01 27 1 0 0 0 -1
01 28 1 0 0 0 -1
01 29 1 0 0 0 -1
01 30 1 0 0 0 -1
01 31 1 0 0 0 -1
01 32 1 0 0 0 -1
01 33 1 0 0 0 -1
01 34 1 0 0 0 -1
01 35 1 0 0 0 -1
01 36 1 0 0 0 -1
01 37 1 0 0 0 -1
01 38 1 0 0 0 -1
01 39 1 0 0 0 -1
01 40 1 0 0 0 -1
01 41 1 0 0 0 -1
01 42 1 0 0 0 -1
01 43 1 0 0 0 -1
01 44 1 0 0 0 -1
01 45 1 0 0 0 -1
01 46 1 0 0 0 -1
01 47 1 0 0 0 -1
01 48 1 0 0 0 -1
01 49 1 0 0 0 -1
01 50 1 0 0 0 -1
01 51 1 0 0 0 -1
01 52 1 0 0 0 -1
01 53 1 0 0 0 -1
01 54 1 0 0 0 -1
01 55 1 0 0 0 -1
01 56 1 0 0 0 -1
01 57 1 0 0 0 -1
01 58 1 0 0 0 -1
01 59 1 0 0 0 -1
01 60 1 0 0 0 -1
01 61 1 0 0 0 -1
01 62 1 0 0 0 -1
01 63 1 0 0 0 -1
02 00 1 0 0 0 -1
02 01 1 0 0 0 -1
02 02 1 0 0 0 -1
02 03 1 0 0 0 -1
02 04 1 0 0 0 -1
02 05 1 0 0 0 -1
02 06 1 0 0 0 -1
02 07 1 0 0 0 -1
02 08 1 0 0 0 -1
02 09 1 0 0 0 -1
02 10 1 0 0 0 -1
02 11 1 0 0 0 -1
02 12 1 0 0 0 -1
02 13 1 0 0 0 -1
02 14 1 0 0 0 -1
02 15 1 0 0 0 -1
02 16 1 0 0 0 -1
02 17 1 0 0 0 -1
02 18 1 0 0 0 -1
02 19 1 0 0 0 -1
02 20 1 0 0 0 -1
02 21 1 0 0 0 -1
02 22 1 0 0 0 -1
02 23 1 0 0 0 -1
02 24 1 0 0 0 -1
02 25 1 0 0 0 -1
02 26 1 0 0 0 -1
02 27 1 0 0 0 -1
02 28 1 0 0 0 -1
02 29 1 0 0 0 -1
02 30 1 0 0 0 -1
02 31 1 0 0 0 -1
02 32 1 0 0 0 -1
02 33 1 0 0 0 -1
02 34 1 0 0 0 -1
02 35 1 0 0 0 -1
02 36 1 0 0 0 -1
02 37 1 0 0 0 -1
02 38 1 0 0 0 -1
02 39 1 0 0 0 -1
02 40 1 0 0 0 -1
02 41 1 0 0 0 -1
02 42 1 0 0 0 -1
02 43 1 0 0 0 -1
02 44 1 0 0 0 -1
02 45 1 0 0 0 -1
02 46 1 0 0 0 -1
02 47 1 0 0 0 -1
02 48 1 0 0 0 -1
02 49 1 0 0 0 -1
02 50 1 0 0 0 -1
02 51 1 0 0 0 -1
02 52 1 0 0 0 -1
02 53 1 0 0 0 -1
02 54 1 0 0 0 -1
02 55 1 0 0 0 -1
02 56 1 0 0 0 -1
02 57 1 0 0 0 -1
02 58 1 0 0 0 -1
02 59 1 0 0 0 -1
02 60 1 0 0 0 -1
02 61 1 0 0 0 -1
02 62 1 0 0 0 -1
02 63 1 0 0 0 -1
03 00 1 0 0 0 -1
03 01 1 0 0 0 -1
03 02 1 0 0 0 -1
03 03 1 0 0 0 -1
03 04 1 0 0 0 -1
03 05 1 0 0 0 -1
03 06 1 0 0 0 -1
03 07 1 0 0 0 -1
03 08 1 0 0 0 -1
03 09 1 0 0 0 -1
03 10 1 0 0 0 -1
03 11 1 0 0 0 -1
03 12 1 0 0 0 -1
03 13 1 0 0 0 -1
03 14 1 0 0 0 -1
03 15 1 0 0 0 -1
03 16 1 0 0 0 -1
03 17 1 0 0 0 -1
03 18 1 0 0 0 -1
03 19 1 0 0 0 -1
03 20 1 0 0 0 -1
03 21 1 0 0 0 -1
03 22 1 0 0 0 -1
03 23 1 0 0 0 -1
03 24 1 0 0 0 -1
03 25 1 0 0 0 -1
03 26 1 0 0 0 -1
03 27 1 0 0 0 -1
03 28 1 0 0 0 -1
03 29 1 0 0 0 -1
03 30 1 0 0 0 -1
03 31 1 0 0 0 -1
03 32 1 0 0 0 -1
03 33 1 0 0 0 -1
03 34 1 0 0 0 -1
03 35 1 0 0 0 -1
03 36 1 0 0 0 -1
03 37 1 0 0 0 -1
03 38 1 0 0 0 -1
03 39 1 0 0 0 -1
03 40 1 0 0 0 -1
03 41 1 0 0 0 -1
03 42 1 0 0 0 -1
03 43 1 0 0 0 -1
03 44 1 0 0 0 -1
03 45 1 0 0 0 -1
03 46 1 0 0 0 -1
03 47 1 0 0 0 -1
03 48 1 0 0 0 -1
03 49 1 0 0 0 -1
03 50 1 0 0 0 -1
03 51 1 0 0 0 -1
03 52 1 0 0 0 -1
03 53 1 0 0 0 -1
03 54 1 0 0 0 -1
03 55 1 0 0 0 -1
03 56 1 0 0 0 -1
03 57 1 0 0 0 -1
03 58 1 0 0 0 -1
03 59 1 0 0 0 -1
03 60 1 0 0 0 -1
03 61 1 0 0 0 -1
03 62 1 0 0 0 -1
03 63 1 0 0 0 -1
04 00 1 0 0 0 -1
04 01 1 0 0 0 -1
04 02 1 0 0 0 -1
04 03 1 0 0 0 -1
04 04 1 0 0 0 -1
04 05 1 0 0 0 -1
04 06 1 0 0 0 -1
04 07 1 0 0 0 -1
04 08 1 0 0 0 -1
04 09 1 0 0 0 -1
04 10 1 0 0 0 -1
04 11 1 0 0 0 -1
04 12 1 0 0 0 -1
04 13 1 0 0 0 -1
04 14 1 0 0 0 -1
04 15 1 0 0 0 -1
04 16 1 0 0 0 -1
04 17 1 0 0 0 -1
04 18 1 0 0 0 -1
04 19 1 0 0 0 -1
04 20 1 0 0 0 -1
04 21 1 0 0 0 -1
04 22 1 0 0 0 -1
04 23 1 0 0 0 -1
04 24 1 0 0 0 -1
04 25 1 0 0 0 -1
04 26 1 0 0 0 -1
04 27 1 0 0 0 -1
04 28 1 0 0 0 -1
04 29 1 0 0 0 -1
04 30 1 0 0 0 -1
04 31 1 0 0 0 -1
04 32 1 0 0 0 -1
04 33 1 0 0 0 -1
04 34 1 0 0 0 -1
04 35 1 0 0 0 -1
04 36 1 0 0 0 -1
04 37 1 0 0 0 -1
... 3774 more lines ...
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 1 0 0 0 -1
00 01 1 0 0 0 -1
00 02 1 0 0 0 -1
00 03 1 0 0 0 -1
00 04 1 0 0 0 -1
00 05 1 0 0 0 -1
00 06 1 0 0 0 -1
00 07 1 0 0 0 -1
00 08 1 0 0 0 -1
00 09 1 0 0 0 -1
00 10 1 0 0 0 -1
00 11 1 0 0 0 -1
00 12 1 0 0 0 -1
00 13 1 0 0 0 -1
00 14 1 0 0 0 -1
00 15 1 0 0 0 -1
00 16 1 0 0 0 -1
00 17 1 0 0 0 -1
00 18 1 0 0 0 -1
00 19 1 0 0 0 -1
00 20 1 0 0 0 -1
00 21 1 0 0 0 -1
00 22 1 0 0 0 -1
00 23 1 0 0 0 -1
00 24 1 0 0 0 -1
00 25 1 0 0 0 -1
00 26 1 0 0 0 -1
00 27 1 0 0 0 -1
00 28 1 0 0 0 -1
00 29 1 0 0 0 -1
00 30 1 0 0 0 -1
00 31 1 0 0 0 -1
00 32 1 0 0 0 -1
00 33 1 0 0 0 -1
00 34 1 0 0 0 -1
00 35 1 0 0 0 -1
00 36 1 0 0 0 -1
00 37 1 0 0 0 -1
00 38 1 0 0 0 -1
00 39 1 0 0 0 -1
00 40 1 0 0 0 -1
00 41 1 0 0 0 -1
00 42 1 0 0 0 -1
00 43 1 0 0 0 -1
00 44 1 0 0 0 -1
00 45 1 0 0 0 -1
00 46 1 0 0 0 -1
00 47 1 0 0 0 -1
00 48 1 0 0 0 -1
00 49 1 0 0 0 -1
00 50 1 0 0 0 -1
00 51 1 0 0 0 -1
00 52 1 0 0 0 -1
00 53 1 0 0 0 -1
00 54 1 0 0 0 -1
00 55 1 0 0 0 -1
00 56 1 0 0 0 -1
00 57 1 0 0 0 -1
00 58 1 0 0 0 -1
00 59 1 0 0 0 -1
00 60 1 0 0 0 -1
00 61 1 0 0 0 -1
00 62 1 0 0 0 -1
00 63 1 0 0 0 -1
01 00 1 0 0 0 -1
01 01 1 0 0 0 -1
01 02 1 0 0 0 -1
01 03 1 0 0 0 -1
01 04 1 0 0 0 -1
01 05 1 0 0 0 -1
01 06 1 0 0 0 -1
01 07 1 0 0 0 -1
01 08 1 0 0 0 -1
01 09 1 0 0 0 -1
01 10 1 0 0 0 -1
01 11 1 0 0 0 -1
01 12 1 0 0 0 -1
01 13 1 0 0 0 -1
01 14 1 0 0 0 -1
01 15 1 0 0 0 -1
01 16 1 0 0 0 -1
01 17 1 0 0 0 -1
01 18 1 0 0 0 -1
01 19 1 0 0 0 -1
01 20 1 0 0 0 -1
01 21 1 0 0 0 -1
01 22 1 0 0 0 -1
01 23 1 0 0 0 -1
01 24 1 0 0 0 -1
01 25 1 0 0 0 -1
01 26 1 0 0 0 -1
01 27 1 0 0 0 -1
01 28 1 0 0 0 -1
01 29 1 0 0 0 -1
01 30 1 0 0 0 -1
01 31 1 0 0 0 -1
01 32 1 0 0 0 -1
01 33 1 0 0 0 -1
01 34 1 0 0 0 -1
01 35 1 0 0 0 -1
01 36 1 0 0 0 -1
01 37 1 0 0 0 -1
01 38 1 0 0 0 -1
01 39 1 0 0 0 -1
01 40 1 0 0 0 -1
01 41 1 0 0 0 -1
01 42 1 0 0 0 -1
01 43 1 0 0 0 -1
01 44 1 0 0 0 -1
01 45 1 0 0 0 -1
01 46 1 0 0 0 -1
01 47 1 0 0 0 -1
01 48 1 0 0 0 -1
01 49 1 0 0 0 -1
01 50 1 0 0 0 -1
01 51 1 0 0 0 -1
01 52 1 0 0 0 -1
01 53 1 0 0 0 -1
01 54 1 0 0 0 -1
01 55 1 0 0 0 -1
01 56 1 0 0 0 -1
01 57 1 0 0 0 -1
01 58 1 0 0 0 -1
01 59 1 0 0 0 -1
01 60 1 0 0 0 -1
01 61 1 0 0 0 -1
01 62 1 0 0 0 -1
01 63 1 0 0 0 -1
02 00 1 0 0 0 -1
02 01 1 0 0 0 -1
02 02 1 0 0 0 -1
02 03 1 0 0 0 -1
02 04 1 0 0 0 -1
02 05 1 0 0 0 -1
02 06 1 0 0 0 -1
02 07 1 0 0 0 -1
02 08 1 0 0 0 -1
02 09 1 0 0 0 -1
02 10 1 0 0 0 -1
02 11 1 0 0 0 -1
02 12 1 0 0 0 -1
02 13 1 0 0 0 -1
02 14 1 0 0 0 -1
02 15 1 0 0 0 -1
02 16 1 0 0 0 -1
02 17 1 0 0 0 -1
02 18 1 0 0 0 -1
02 19 1 0 0 0 -1
02 20 1 0 0 0 -1
02 21 1 0 0 0 -1
02 22 1 0 0 0 -1
02 23 1 0 0 0 -1
02 24 1 0 0 0 -1
02 25 1 0 0 0 -1
02 26 1 0 0 0 -1
02 27 1 0 0 0 -1
02 28 1 0 0 0 -1
02 29 1 0 0 0 -1
02 30 1 0 0 0 -1
02 31 1 0 0 0 -1
02 32 1 0 0 0 -1
02 33 1 0 0 0 -1
02 34 1 0 0 0 -1
02 35 1 0 0 0 -1
02 36 1 0 0 0 -1
02 37 1 0 0 0 -1
02 38 1 0 0 0 -1
02 39 1 0 0 0 -1
02 40 1 0 0 0 -1
02 41 1 0 0 0 -1
02 42 1 0 0 0 -1
02 43 1 0 0 0 -1
02 44 1 0 0 0 -1
02 45 1 0 0 0 -1
02 46 1 0 0 0 -1
02 47 1 0 0 0 -1
02 48 1 0 0 0 -1
02 49 1 0 0 0 -1
02 50 1 0 0 0 -1
02 51 1 0 0 0 -1
02 52 1 0 0 0 -1
02 53 1 0 0 0 -1
02 54 1 0 0 0 -1
02 55 1 0 0 0 -1
02 56 1 0 0 0 -1
02 57 1 0 0 0 -1
02 58 1 0 0 0 -1
02 59 1 0 0 0 -1
02 60 1 0 0 0 -1
02 61 1 0 0 0 -1
02 62 1 0 0 0 -1
02 63 1 0 0 0 -1
03 00 1 0 0 0 -1
03 01 1 0 0 0 -1
03 02 1 0 0 0 -1
03 03 1 0 0 0 -1
03 04 1 0 0 0 -1
03 05 1 0 0 0 -1
03 06 1 0 0 0 -1
03 07 1 0 0 0 -1
03 08 1 0 0 0 -1
03 09 1 0 0 0 -1
03 10 1 0 0 0 -1
03 11 1 0 0 0 -1
03 12 1 0 0 0 -1
03 13 1 0 0 0 -1
03 14 1 0 0 0 -1
03 15 1 0 0 0 -1
03 16 1 0 0 0 -1
03 17 1 0 0 0 -1
03 18 1 0 0 0 -1
03 19 1 0 0 0 -1
03 20 1 0 0 0 -1
03 21 1 0 0 0 -1
03 22 1 0 0 0 -1
03 23 1 0 0 0 -1
03 24 1 0 0 0 -1
03 25 1 0 0 0 -1
03 26 1 0 0 0 -1
03 27 1 0 0 0 -1
03 28 1 0 0 0 -1
03 29 1 0 0 0 -1
03 30 1 0 0 0 -1
03 31 1 0 0 0 -1
03 32 1 0 0 0 -1
03 33 1 0 0 0 -1
03 34 1 0 0 0 -1
03 35 1 0 0 0 -1
03 36 1 0 0 0 -1
03 37 1 0 0 0 -1
03 38 1 0 0 0 -1
03 39 1 0 0 0 -1
03 40 1 0 0 0 -1
03 41 1 0 0 0 -1
03 42 1 0 0 0 -1
03 43 1 0 0 0 -1
03 44 1 0 0 0 -1
03 45 1 0 0 0 -1
03 46 1 0 0 0 -1
03 47 1 0 0 0 -1
03 48 1 0 0 0 -1
03 49 1 0 0 0 -1
03 50 1 0 0 0 -1
03 51 1 0 0 0 -1
03 52 1 0 0 0 -1
03 53 1 0 0 0 -1
03 54 1 0 0 0 -1
03 55 1 0 0 0 -1
03 56 1 0 0 0 -1
03 57 1 0 0 0 -1
03 58 1 0 0 0 -1
03 59 1 0 0 0 -1
03 60 1 0 0 0 -1
03 61 1 0 0 0 -1
03 62 1 0 0 0 -1
03 63 1 0 0 0 -1
04 00 1 0 0 0 -1
04 01 1 0 0 0 -1
04 02 1 0 0 0 -1
04 03 1 0 0 0 -1
04 04 1 0 0 0 -1
04 05 1 0 0 0 -1
04 06 1 0 0 0 -1
04 07 1 0 0 0 -1
04 08 1 0 0 0 -1
04 09 1 0 0 0 -1
04 10 1 0 0 0 -1
04 11 1 0 0 0 -1
04 12 1 0 0 0 -1
04 13 1 0 0 0 -1
04 14 1 0 0 0 -1
04 15 1 0 0 0 -1
04 16 1 0 0 0 -1
04 17 1 0 0 0 -1
04 18 1 0 0 0 -1
04 19 1 0 0 0 -1
04 20 1 0 0 0 -1
04 21 1 0 0 0 -1
04 22 1 0 0 0 -1
04 23 1 0 0 0 -1
04 24 1 0 0 0 -1
04 25 1 0 0 0 -1
04 26 1 0 0 0 -1
04 27 1 0 0 0 -1
04 28 1 0 0 0 -1
04 29 1 0 0 0 -1
04 30 1 0 0 0 -1
04 31 1 0 0 0 -1
04 32 1 0 0 0 -1
04 33 1 0 0 0 -1
04 34 1 0 0 0 -1
04 35 1 0 0 0 -1
04 36 1 0 0 0 -1
04 37 1 0 0 0 -1
... 3774 more lines ...
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/run$6R_mpw3$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
#NF_THR30
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/04_HV_THR22/20230705_104444_threshold_scan_interpreted.h5
#MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 480
STOP_COLUMN = 492
WAIT_FOR_FPGA = 1
CONFIG_ID = 9
ELOG_CATEGORY = Beam # Debug, Beam, VoltageScan, Scan
COMMENT_IN_CONF = "Comment here"
ELOG_OUTPUT_PATH = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs"
[Producer.hameg]
HV = 10
#BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
37
|
Wed Jul 5 11:50:00 2023 |
tb-crew | searching correlations | 640 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 05.07.2023 11:45:25 | 05.07.2023 11:45:50 | 0 |
automatic log for run 640
Comment:
running with base & piggy
Only very few pixel active |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.35
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 1 0 0 0 -1
00 01 1 0 0 0 -1
00 02 1 0 0 0 -1
00 03 1 0 0 0 -1
00 04 1 0 0 0 -1
00 05 1 0 0 0 -1
00 06 1 0 0 0 -1
00 07 1 0 0 0 -1
00 08 1 0 0 0 -1
00 09 1 0 0 0 -1
00 10 1 0 0 0 -1
00 11 1 0 0 0 -1
00 12 1 0 0 0 -1
00 13 1 0 0 0 -1
00 14 1 0 0 0 -1
00 15 1 0 0 0 -1
00 16 1 0 0 0 -1
00 17 1 0 0 0 -1
00 18 1 0 0 0 -1
00 19 1 0 0 0 -1
00 20 1 0 0 0 -1
00 21 1 0 0 0 -1
00 22 1 0 0 0 -1
00 23 1 0 0 0 -1
00 24 1 0 0 0 -1
00 25 1 0 0 0 -1
00 26 1 0 0 0 -1
00 27 1 0 0 0 -1
00 28 1 0 0 0 -1
00 29 1 0 0 0 -1
00 30 1 0 0 0 -1
00 31 1 0 0 0 -1
00 32 1 0 0 0 -1
00 33 1 0 0 0 -1
00 34 1 0 0 0 -1
00 35 1 0 0 0 -1
00 36 1 0 0 0 -1
00 37 1 0 0 0 -1
00 38 1 0 0 0 -1
00 39 1 0 0 0 -1
00 40 1 0 0 0 -1
00 41 1 0 0 0 -1
00 42 1 0 0 0 -1
00 43 1 0 0 0 -1
00 44 1 0 0 0 -1
00 45 1 0 0 0 -1
00 46 1 0 0 0 -1
00 47 1 0 0 0 -1
00 48 1 0 0 0 -1
00 49 1 0 0 0 -1
00 50 1 0 0 0 -1
00 51 1 0 0 0 -1
00 52 1 0 0 0 -1
00 53 1 0 0 0 -1
00 54 1 0 0 0 -1
00 55 1 0 0 0 -1
00 56 1 0 0 0 -1
00 57 1 0 0 0 -1
00 58 1 0 0 0 -1
00 59 1 0 0 0 -1
00 60 1 0 0 0 -1
00 61 1 0 0 0 -1
00 62 1 0 0 0 -1
00 63 1 0 0 0 -1
01 00 1 0 0 0 -1
01 01 1 0 0 0 -1
01 02 1 0 0 0 -1
01 03 1 0 0 0 -1
01 04 1 0 0 0 -1
01 05 1 0 0 0 -1
01 06 1 0 0 0 -1
01 07 1 0 0 0 -1
01 08 1 0 0 0 -1
01 09 1 0 0 0 -1
01 10 1 0 0 0 -1
01 11 1 0 0 0 -1
01 12 1 0 0 0 -1
01 13 1 0 0 0 -1
01 14 1 0 0 0 -1
01 15 1 0 0 0 -1
01 16 1 0 0 0 -1
01 17 1 0 0 0 -1
01 18 1 0 0 0 -1
01 19 1 0 0 0 -1
01 20 1 0 0 0 -1
01 21 1 0 0 0 -1
01 22 1 0 0 0 -1
01 23 1 0 0 0 -1
01 24 1 0 0 0 -1
01 25 1 0 0 0 -1
01 26 1 0 0 0 -1
01 27 1 0 0 0 -1
01 28 1 0 0 0 -1
01 29 1 0 0 0 -1
01 30 1 0 0 0 -1
01 31 1 0 0 0 -1
01 32 1 0 0 0 -1
01 33 1 0 0 0 -1
01 34 1 0 0 0 -1
01 35 1 0 0 0 -1
01 36 1 0 0 0 -1
01 37 1 0 0 0 -1
01 38 1 0 0 0 -1
01 39 1 0 0 0 -1
01 40 1 0 0 0 -1
01 41 1 0 0 0 -1
01 42 1 0 0 0 -1
01 43 1 0 0 0 -1
01 44 1 0 0 0 -1
01 45 1 0 0 0 -1
01 46 1 0 0 0 -1
01 47 1 0 0 0 -1
01 48 1 0 0 0 -1
01 49 1 0 0 0 -1
01 50 1 0 0 0 -1
01 51 1 0 0 0 -1
01 52 1 0 0 0 -1
01 53 1 0 0 0 -1
01 54 1 0 0 0 -1
01 55 1 0 0 0 -1
01 56 1 0 0 0 -1
01 57 1 0 0 0 -1
01 58 1 0 0 0 -1
01 59 1 0 0 0 -1
01 60 1 0 0 0 -1
01 61 1 0 0 0 -1
01 62 1 0 0 0 -1
01 63 1 0 0 0 -1
02 00 1 0 0 0 -1
02 01 1 0 0 0 -1
02 02 1 0 0 0 -1
02 03 1 0 0 0 -1
02 04 1 0 0 0 -1
02 05 1 0 0 0 -1
02 06 1 0 0 0 -1
02 07 1 0 0 0 -1
02 08 1 0 0 0 -1
02 09 1 0 0 0 -1
02 10 1 0 0 0 -1
02 11 1 0 0 0 -1
02 12 1 0 0 0 -1
02 13 1 0 0 0 -1
02 14 1 0 0 0 -1
02 15 1 0 0 0 -1
02 16 1 0 0 0 -1
02 17 1 0 0 0 -1
02 18 1 0 0 0 -1
02 19 1 0 0 0 -1
02 20 1 0 0 0 -1
02 21 1 0 0 0 -1
02 22 1 0 0 0 -1
02 23 1 0 0 0 -1
02 24 1 0 0 0 -1
02 25 1 0 0 0 -1
02 26 1 0 0 0 -1
02 27 1 0 0 0 -1
02 28 1 0 0 0 -1
02 29 1 0 0 0 -1
02 30 1 0 0 0 -1
02 31 1 0 0 0 -1
02 32 1 0 0 0 -1
02 33 1 0 0 0 -1
02 34 1 0 0 0 -1
02 35 1 0 0 0 -1
02 36 1 0 0 0 -1
02 37 1 0 0 0 -1
02 38 1 0 0 0 -1
02 39 1 0 0 0 -1
02 40 1 0 0 0 -1
02 41 1 0 0 0 -1
02 42 1 0 0 0 -1
02 43 1 0 0 0 -1
02 44 1 0 0 0 -1
02 45 1 0 0 0 -1
02 46 1 0 0 0 -1
02 47 1 0 0 0 -1
02 48 1 0 0 0 -1
02 49 1 0 0 0 -1
02 50 1 0 0 0 -1
02 51 1 0 0 0 -1
02 52 1 0 0 0 -1
02 53 1 0 0 0 -1
02 54 1 0 0 0 -1
02 55 1 0 0 0 -1
02 56 1 0 0 0 -1
02 57 1 0 0 0 -1
02 58 1 0 0 0 -1
02 59 1 0 0 0 -1
02 60 1 0 0 0 -1
02 61 1 0 0 0 -1
02 62 1 0 0 0 -1
02 63 1 0 0 0 -1
03 00 1 0 0 0 -1
03 01 1 0 0 0 -1
03 02 1 0 0 0 -1
03 03 1 0 0 0 -1
03 04 1 0 0 0 -1
03 05 1 0 0 0 -1
03 06 1 0 0 0 -1
03 07 1 0 0 0 -1
03 08 1 0 0 0 -1
03 09 1 0 0 0 -1
03 10 1 0 0 0 -1
03 11 1 0 0 0 -1
03 12 1 0 0 0 -1
03 13 1 0 0 0 -1
03 14 1 0 0 0 -1
03 15 1 0 0 0 -1
03 16 1 0 0 0 -1
03 17 1 0 0 0 -1
03 18 1 0 0 0 -1
03 19 1 0 0 0 -1
03 20 1 0 0 0 -1
03 21 1 0 0 0 -1
03 22 1 0 0 0 -1
03 23 1 0 0 0 -1
03 24 1 0 0 0 -1
03 25 1 0 0 0 -1
03 26 1 0 0 0 -1
03 27 1 0 0 0 -1
03 28 1 0 0 0 -1
03 29 1 0 0 0 -1
03 30 1 0 0 0 -1
03 31 1 0 0 0 -1
03 32 1 0 0 0 -1
03 33 1 0 0 0 -1
03 34 1 0 0 0 -1
03 35 1 0 0 0 -1
03 36 1 0 0 0 -1
03 37 1 0 0 0 -1
03 38 1 0 0 0 -1
03 39 1 0 0 0 -1
03 40 1 0 0 0 -1
03 41 1 0 0 0 -1
03 42 1 0 0 0 -1
03 43 1 0 0 0 -1
03 44 1 0 0 0 -1
03 45 1 0 0 0 -1
03 46 1 0 0 0 -1
03 47 1 0 0 0 -1
03 48 1 0 0 0 -1
03 49 1 0 0 0 -1
03 50 1 0 0 0 -1
03 51 1 0 0 0 -1
03 52 1 0 0 0 -1
03 53 1 0 0 0 -1
03 54 1 0 0 0 -1
03 55 1 0 0 0 -1
03 56 1 0 0 0 -1
03 57 1 0 0 0 -1
03 58 1 0 0 0 -1
03 59 1 0 0 0 -1
03 60 1 0 0 0 -1
03 61 1 0 0 0 -1
03 62 1 0 0 0 -1
03 63 1 0 0 0 -1
04 00 1 0 0 0 -1
04 01 1 0 0 0 -1
04 02 1 0 0 0 -1
04 03 1 0 0 0 -1
04 04 1 0 0 0 -1
04 05 1 0 0 0 -1
04 06 1 0 0 0 -1
04 07 1 0 0 0 -1
04 08 1 0 0 0 -1
04 09 1 0 0 0 -1
04 10 1 0 0 0 -1
04 11 1 0 0 0 -1
04 12 1 0 0 0 -1
04 13 1 0 0 0 -1
04 14 1 0 0 0 -1
04 15 1 0 0 0 -1
04 16 1 0 0 0 -1
04 17 1 0 0 0 -1
04 18 1 0 0 0 -1
04 19 1 0 0 0 -1
04 20 1 0 0 0 -1
04 21 1 0 0 0 -1
04 22 1 0 0 0 -1
04 23 1 0 0 0 -1
04 24 1 0 0 0 -1
04 25 1 0 0 0 -1
04 26 1 0 0 0 -1
04 27 1 0 0 0 -1
04 28 1 0 0 0 -1
04 29 1 0 0 0 -1
04 30 1 0 0 0 -1
04 31 1 0 0 0 -1
04 32 1 0 0 0 -1
04 33 1 0 0 0 -1
04 34 1 0 0 0 -1
04 35 1 0 0 0 -1
04 36 1 0 0 0 -1
04 37 1 0 0 0 -1
... 3774 more lines ...
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 1 0 0 0 -1
00 01 1 0 0 0 -1
00 02 1 0 0 0 -1
00 03 1 0 0 0 -1
00 04 1 0 0 0 -1
00 05 1 0 0 0 -1
00 06 1 0 0 0 -1
00 07 1 0 0 0 -1
00 08 1 0 0 0 -1
00 09 1 0 0 0 -1
00 10 1 0 0 0 -1
00 11 1 0 0 0 -1
00 12 1 0 0 0 -1
00 13 1 0 0 0 -1
00 14 1 0 0 0 -1
00 15 1 0 0 0 -1
00 16 1 0 0 0 -1
00 17 1 0 0 0 -1
00 18 1 0 0 0 -1
00 19 1 0 0 0 -1
00 20 1 0 0 0 -1
00 21 1 0 0 0 -1
00 22 1 0 0 0 -1
00 23 1 0 0 0 -1
00 24 1 0 0 0 -1
00 25 1 0 0 0 -1
00 26 1 0 0 0 -1
00 27 1 0 0 0 -1
00 28 1 0 0 0 -1
00 29 1 0 0 0 -1
00 30 1 0 0 0 -1
00 31 1 0 0 0 -1
00 32 1 0 0 0 -1
00 33 1 0 0 0 -1
00 34 1 0 0 0 -1
00 35 1 0 0 0 -1
00 36 1 0 0 0 -1
00 37 1 0 0 0 -1
00 38 1 0 0 0 -1
00 39 1 0 0 0 -1
00 40 1 0 0 0 -1
00 41 1 0 0 0 -1
00 42 1 0 0 0 -1
00 43 1 0 0 0 -1
00 44 1 0 0 0 -1
00 45 1 0 0 0 -1
00 46 1 0 0 0 -1
00 47 1 0 0 0 -1
00 48 1 0 0 0 -1
00 49 1 0 0 0 -1
00 50 1 0 0 0 -1
00 51 1 0 0 0 -1
00 52 1 0 0 0 -1
00 53 1 0 0 0 -1
00 54 1 0 0 0 -1
00 55 1 0 0 0 -1
00 56 1 0 0 0 -1
00 57 1 0 0 0 -1
00 58 1 0 0 0 -1
00 59 1 0 0 0 -1
00 60 1 0 0 0 -1
00 61 1 0 0 0 -1
00 62 1 0 0 0 -1
00 63 1 0 0 0 -1
01 00 1 0 0 0 -1
01 01 1 0 0 0 -1
01 02 1 0 0 0 -1
01 03 1 0 0 0 -1
01 04 1 0 0 0 -1
01 05 1 0 0 0 -1
01 06 1 0 0 0 -1
01 07 1 0 0 0 -1
01 08 1 0 0 0 -1
01 09 1 0 0 0 -1
01 10 1 0 0 0 -1
01 11 1 0 0 0 -1
01 12 1 0 0 0 -1
01 13 1 0 0 0 -1
01 14 1 0 0 0 -1
01 15 1 0 0 0 -1
01 16 1 0 0 0 -1
01 17 1 0 0 0 -1
01 18 1 0 0 0 -1
01 19 1 0 0 0 -1
01 20 1 0 0 0 -1
01 21 1 0 0 0 -1
01 22 1 0 0 0 -1
01 23 1 0 0 0 -1
01 24 1 0 0 0 -1
01 25 1 0 0 0 -1
01 26 1 0 0 0 -1
01 27 1 0 0 0 -1
01 28 1 0 0 0 -1
01 29 1 0 0 0 -1
01 30 1 0 0 0 -1
01 31 1 0 0 0 -1
01 32 1 0 0 0 -1
01 33 1 0 0 0 -1
01 34 1 0 0 0 -1
01 35 1 0 0 0 -1
01 36 1 0 0 0 -1
01 37 1 0 0 0 -1
01 38 1 0 0 0 -1
01 39 1 0 0 0 -1
01 40 1 0 0 0 -1
01 41 1 0 0 0 -1
01 42 1 0 0 0 -1
01 43 1 0 0 0 -1
01 44 1 0 0 0 -1
01 45 1 0 0 0 -1
01 46 1 0 0 0 -1
01 47 1 0 0 0 -1
01 48 1 0 0 0 -1
01 49 1 0 0 0 -1
01 50 1 0 0 0 -1
01 51 1 0 0 0 -1
01 52 1 0 0 0 -1
01 53 1 0 0 0 -1
01 54 1 0 0 0 -1
01 55 1 0 0 0 -1
01 56 1 0 0 0 -1
01 57 1 0 0 0 -1
01 58 1 0 0 0 -1
01 59 1 0 0 0 -1
01 60 1 0 0 0 -1
01 61 1 0 0 0 -1
01 62 1 0 0 0 -1
01 63 1 0 0 0 -1
02 00 1 0 0 0 -1
02 01 1 0 0 0 -1
02 02 1 0 0 0 -1
02 03 1 0 0 0 -1
02 04 1 0 0 0 -1
02 05 1 0 0 0 -1
02 06 1 0 0 0 -1
02 07 1 0 0 0 -1
02 08 1 0 0 0 -1
02 09 1 0 0 0 -1
02 10 1 0 0 0 -1
02 11 1 0 0 0 -1
02 12 1 0 0 0 -1
02 13 1 0 0 0 -1
02 14 1 0 0 0 -1
02 15 1 0 0 0 -1
02 16 1 0 0 0 -1
02 17 1 0 0 0 -1
02 18 1 0 0 0 -1
02 19 1 0 0 0 -1
02 20 1 0 0 0 -1
02 21 1 0 0 0 -1
02 22 1 0 0 0 -1
02 23 1 0 0 0 -1
02 24 1 0 0 0 -1
02 25 1 0 0 0 -1
02 26 1 0 0 0 -1
02 27 1 0 0 0 -1
02 28 1 0 0 0 -1
02 29 1 0 0 0 -1
02 30 1 0 0 0 -1
02 31 1 0 0 0 -1
02 32 1 0 0 0 -1
02 33 1 0 0 0 -1
02 34 1 0 0 0 -1
02 35 1 0 0 0 -1
02 36 1 0 0 0 -1
02 37 1 0 0 0 -1
02 38 1 0 0 0 -1
02 39 1 0 0 0 -1
02 40 1 0 0 0 -1
02 41 1 0 0 0 -1
02 42 1 0 0 0 -1
02 43 1 0 0 0 -1
02 44 1 0 0 0 -1
02 45 1 0 0 0 -1
02 46 1 0 0 0 -1
02 47 1 0 0 0 -1
02 48 1 0 0 0 -1
02 49 1 0 0 0 -1
02 50 1 0 0 0 -1
02 51 1 0 0 0 -1
02 52 1 0 0 0 -1
02 53 1 0 0 0 -1
02 54 1 0 0 0 -1
02 55 1 0 0 0 -1
02 56 1 0 0 0 -1
02 57 1 0 0 0 -1
02 58 1 0 0 0 -1
02 59 1 0 0 0 -1
02 60 1 0 0 0 -1
02 61 1 0 0 0 -1
02 62 1 0 0 0 -1
02 63 1 0 0 0 -1
03 00 1 0 0 0 -1
03 01 1 0 0 0 -1
03 02 1 0 0 0 -1
03 03 1 0 0 0 -1
03 04 1 0 0 0 -1
03 05 1 0 0 0 -1
03 06 1 0 0 0 -1
03 07 1 0 0 0 -1
03 08 1 0 0 0 -1
03 09 1 0 0 0 -1
03 10 1 0 0 0 -1
03 11 1 0 0 0 -1
03 12 1 0 0 0 -1
03 13 1 0 0 0 -1
03 14 1 0 0 0 -1
03 15 1 0 0 0 -1
03 16 1 0 0 0 -1
03 17 1 0 0 0 -1
03 18 1 0 0 0 -1
03 19 1 0 0 0 -1
03 20 1 0 0 0 -1
03 21 1 0 0 0 -1
03 22 1 0 0 0 -1
03 23 1 0 0 0 -1
03 24 1 0 0 0 -1
03 25 1 0 0 0 -1
03 26 1 0 0 0 -1
03 27 1 0 0 0 -1
03 28 1 0 0 0 -1
03 29 1 0 0 0 -1
03 30 1 0 0 0 -1
03 31 1 0 0 0 -1
03 32 1 0 0 0 -1
03 33 1 0 0 0 -1
03 34 1 0 0 0 -1
03 35 1 0 0 0 -1
03 36 1 0 0 0 -1
03 37 1 0 0 0 -1
03 38 1 0 0 0 -1
03 39 1 0 0 0 -1
03 40 1 0 0 0 -1
03 41 1 0 0 0 -1
03 42 1 0 0 0 -1
03 43 1 0 0 0 -1
03 44 1 0 0 0 -1
03 45 1 0 0 0 -1
03 46 1 0 0 0 -1
03 47 1 0 0 0 -1
03 48 1 0 0 0 -1
03 49 1 0 0 0 -1
03 50 1 0 0 0 -1
03 51 1 0 0 0 -1
03 52 1 0 0 0 -1
03 53 1 0 0 0 -1
03 54 1 0 0 0 -1
03 55 1 0 0 0 -1
03 56 1 0 0 0 -1
03 57 1 0 0 0 -1
03 58 1 0 0 0 -1
03 59 1 0 0 0 -1
03 60 1 0 0 0 -1
03 61 1 0 0 0 -1
03 62 1 0 0 0 -1
03 63 1 0 0 0 -1
04 00 1 0 0 0 -1
04 01 1 0 0 0 -1
04 02 1 0 0 0 -1
04 03 1 0 0 0 -1
04 04 1 0 0 0 -1
04 05 1 0 0 0 -1
04 06 1 0 0 0 -1
04 07 1 0 0 0 -1
04 08 1 0 0 0 -1
04 09 1 0 0 0 -1
04 10 1 0 0 0 -1
04 11 1 0 0 0 -1
04 12 1 0 0 0 -1
04 13 1 0 0 0 -1
04 14 1 0 0 0 -1
04 15 1 0 0 0 -1
04 16 1 0 0 0 -1
04 17 1 0 0 0 -1
04 18 1 0 0 0 -1
04 19 1 0 0 0 -1
04 20 1 0 0 0 -1
04 21 1 0 0 0 -1
04 22 1 0 0 0 -1
04 23 1 0 0 0 -1
04 24 1 0 0 0 -1
04 25 1 0 0 0 -1
04 26 1 0 0 0 -1
04 27 1 0 0 0 -1
04 28 1 0 0 0 -1
04 29 1 0 0 0 -1
04 30 1 0 0 0 -1
04 31 1 0 0 0 -1
04 32 1 0 0 0 -1
04 33 1 0 0 0 -1
04 34 1 0 0 0 -1
04 35 1 0 0 0 -1
04 36 1 0 0 0 -1
04 37 1 0 0 0 -1
... 3774 more lines ...
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/run$6R_mpw3$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
#NF_THR30
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/04_HV_THR22/20230705_104444_threshold_scan_interpreted.h5
#MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 480
STOP_COLUMN = 492
WAIT_FOR_FPGA = 1
CONFIG_ID = 9
ELOG_CATEGORY = Beam # Debug, Beam, VoltageScan, Scan
COMMENT_IN_CONF = "Comment here"
ELOG_OUTPUT_PATH = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs"
[Producer.hameg]
HV = 10
#BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
36
|
Wed Jul 5 11:39:02 2023 |
tb-crew | searching correlations | 639 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 05.07.2023 11:32:06 | 05.07.2023 11:34:52 | 2 |
automatic log for run 639
Comment:
running with base & piggy
Only very few pixel active |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.35
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 1 0 0 0 -1
00 01 1 0 0 0 -1
00 02 1 0 0 0 -1
00 03 1 0 0 0 -1
00 04 1 0 0 0 -1
00 05 1 0 0 0 -1
00 06 1 0 0 0 -1
00 07 1 0 0 0 -1
00 08 1 0 0 0 -1
00 09 1 0 0 0 -1
00 10 1 0 0 0 -1
00 11 1 0 0 0 -1
00 12 1 0 0 0 -1
00 13 1 0 0 0 -1
00 14 1 0 0 0 -1
00 15 1 0 0 0 -1
00 16 1 0 0 0 -1
00 17 1 0 0 0 -1
00 18 1 0 0 0 -1
00 19 1 0 0 0 -1
00 20 1 0 0 0 -1
00 21 1 0 0 0 -1
00 22 1 0 0 0 -1
00 23 1 0 0 0 -1
00 24 1 0 0 0 -1
00 25 1 0 0 0 -1
00 26 1 0 0 0 -1
00 27 1 0 0 0 -1
00 28 1 0 0 0 -1
00 29 1 0 0 0 -1
00 30 1 0 0 0 -1
00 31 1 0 0 0 -1
00 32 1 0 0 0 -1
00 33 1 0 0 0 -1
00 34 1 0 0 0 -1
00 35 1 0 0 0 -1
00 36 1 0 0 0 -1
00 37 1 0 0 0 -1
00 38 1 0 0 0 -1
00 39 1 0 0 0 -1
00 40 1 0 0 0 -1
00 41 1 0 0 0 -1
00 42 1 0 0 0 -1
00 43 1 0 0 0 -1
00 44 1 0 0 0 -1
00 45 1 0 0 0 -1
00 46 1 0 0 0 -1
00 47 1 0 0 0 -1
00 48 1 0 0 0 -1
00 49 1 0 0 0 -1
00 50 1 0 0 0 -1
00 51 1 0 0 0 -1
00 52 1 0 0 0 -1
00 53 1 0 0 0 -1
00 54 1 0 0 0 -1
00 55 1 0 0 0 -1
00 56 1 0 0 0 -1
00 57 1 0 0 0 -1
00 58 1 0 0 0 -1
00 59 1 0 0 0 -1
00 60 1 0 0 0 -1
00 61 1 0 0 0 -1
00 62 1 0 0 0 -1
00 63 1 0 0 0 -1
01 00 1 0 0 0 -1
01 01 1 0 0 0 -1
01 02 1 0 0 0 -1
01 03 1 0 0 0 -1
01 04 1 0 0 0 -1
01 05 1 0 0 0 -1
01 06 1 0 0 0 -1
01 07 1 0 0 0 -1
01 08 1 0 0 0 -1
01 09 1 0 0 0 -1
01 10 1 0 0 0 -1
01 11 1 0 0 0 -1
01 12 1 0 0 0 -1
01 13 1 0 0 0 -1
01 14 1 0 0 0 -1
01 15 1 0 0 0 -1
01 16 1 0 0 0 -1
01 17 1 0 0 0 -1
01 18 1 0 0 0 -1
01 19 1 0 0 0 -1
01 20 1 0 0 0 -1
01 21 1 0 0 0 -1
01 22 1 0 0 0 -1
01 23 1 0 0 0 -1
01 24 1 0 0 0 -1
01 25 1 0 0 0 -1
01 26 1 0 0 0 -1
01 27 1 0 0 0 -1
01 28 1 0 0 0 -1
01 29 1 0 0 0 -1
01 30 1 0 0 0 -1
01 31 1 0 0 0 -1
01 32 1 0 0 0 -1
01 33 1 0 0 0 -1
01 34 1 0 0 0 -1
01 35 1 0 0 0 -1
01 36 1 0 0 0 -1
01 37 1 0 0 0 -1
01 38 1 0 0 0 -1
01 39 1 0 0 0 -1
01 40 1 0 0 0 -1
01 41 1 0 0 0 -1
01 42 1 0 0 0 -1
01 43 1 0 0 0 -1
01 44 1 0 0 0 -1
01 45 1 0 0 0 -1
01 46 1 0 0 0 -1
01 47 1 0 0 0 -1
01 48 1 0 0 0 -1
01 49 1 0 0 0 -1
01 50 1 0 0 0 -1
01 51 1 0 0 0 -1
01 52 1 0 0 0 -1
01 53 1 0 0 0 -1
01 54 1 0 0 0 -1
01 55 1 0 0 0 -1
01 56 1 0 0 0 -1
01 57 1 0 0 0 -1
01 58 1 0 0 0 -1
01 59 1 0 0 0 -1
01 60 1 0 0 0 -1
01 61 1 0 0 0 -1
01 62 1 0 0 0 -1
01 63 1 0 0 0 -1
02 00 1 0 0 0 -1
02 01 1 0 0 0 -1
02 02 1 0 0 0 -1
02 03 1 0 0 0 -1
02 04 1 0 0 0 -1
02 05 1 0 0 0 -1
02 06 1 0 0 0 -1
02 07 1 0 0 0 -1
02 08 1 0 0 0 -1
02 09 1 0 0 0 -1
02 10 1 0 0 0 -1
02 11 1 0 0 0 -1
02 12 1 0 0 0 -1
02 13 1 0 0 0 -1
02 14 1 0 0 0 -1
02 15 1 0 0 0 -1
02 16 1 0 0 0 -1
02 17 1 0 0 0 -1
02 18 1 0 0 0 -1
02 19 1 0 0 0 -1
02 20 1 0 0 0 -1
02 21 1 0 0 0 -1
02 22 1 0 0 0 -1
02 23 1 0 0 0 -1
02 24 1 0 0 0 -1
02 25 1 0 0 0 -1
02 26 1 0 0 0 -1
02 27 1 0 0 0 -1
02 28 1 0 0 0 -1
02 29 1 0 0 0 -1
02 30 1 0 0 0 -1
02 31 1 0 0 0 -1
02 32 1 0 0 0 -1
02 33 1 0 0 0 -1
02 34 1 0 0 0 -1
02 35 1 0 0 0 -1
02 36 1 0 0 0 -1
02 37 1 0 0 0 -1
02 38 1 0 0 0 -1
02 39 1 0 0 0 -1
02 40 1 0 0 0 -1
02 41 1 0 0 0 -1
02 42 1 0 0 0 -1
02 43 1 0 0 0 -1
02 44 1 0 0 0 -1
02 45 1 0 0 0 -1
02 46 1 0 0 0 -1
02 47 1 0 0 0 -1
02 48 1 0 0 0 -1
02 49 1 0 0 0 -1
02 50 1 0 0 0 -1
02 51 1 0 0 0 -1
02 52 1 0 0 0 -1
02 53 1 0 0 0 -1
02 54 1 0 0 0 -1
02 55 1 0 0 0 -1
02 56 1 0 0 0 -1
02 57 1 0 0 0 -1
02 58 1 0 0 0 -1
02 59 1 0 0 0 -1
02 60 1 0 0 0 -1
02 61 1 0 0 0 -1
02 62 1 0 0 0 -1
02 63 1 0 0 0 -1
03 00 1 0 0 0 -1
03 01 1 0 0 0 -1
03 02 1 0 0 0 -1
03 03 1 0 0 0 -1
03 04 1 0 0 0 -1
03 05 1 0 0 0 -1
03 06 1 0 0 0 -1
03 07 1 0 0 0 -1
03 08 1 0 0 0 -1
03 09 1 0 0 0 -1
03 10 1 0 0 0 -1
03 11 1 0 0 0 -1
03 12 1 0 0 0 -1
03 13 1 0 0 0 -1
03 14 1 0 0 0 -1
03 15 1 0 0 0 -1
03 16 1 0 0 0 -1
03 17 1 0 0 0 -1
03 18 1 0 0 0 -1
03 19 1 0 0 0 -1
03 20 1 0 0 0 -1
03 21 1 0 0 0 -1
03 22 1 0 0 0 -1
03 23 1 0 0 0 -1
03 24 1 0 0 0 -1
03 25 1 0 0 0 -1
03 26 1 0 0 0 -1
03 27 1 0 0 0 -1
03 28 1 0 0 0 -1
03 29 1 0 0 0 -1
03 30 1 0 0 0 -1
03 31 1 0 0 0 -1
03 32 1 0 0 0 -1
03 33 1 0 0 0 -1
03 34 1 0 0 0 -1
03 35 1 0 0 0 -1
03 36 1 0 0 0 -1
03 37 1 0 0 0 -1
03 38 1 0 0 0 -1
03 39 1 0 0 0 -1
03 40 1 0 0 0 -1
03 41 1 0 0 0 -1
03 42 1 0 0 0 -1
03 43 1 0 0 0 -1
03 44 1 0 0 0 -1
03 45 1 0 0 0 -1
03 46 1 0 0 0 -1
03 47 1 0 0 0 -1
03 48 1 0 0 0 -1
03 49 1 0 0 0 -1
03 50 1 0 0 0 -1
03 51 1 0 0 0 -1
03 52 1 0 0 0 -1
03 53 1 0 0 0 -1
03 54 1 0 0 0 -1
03 55 1 0 0 0 -1
03 56 1 0 0 0 -1
03 57 1 0 0 0 -1
03 58 1 0 0 0 -1
03 59 1 0 0 0 -1
03 60 1 0 0 0 -1
03 61 1 0 0 0 -1
03 62 1 0 0 0 -1
03 63 1 0 0 0 -1
04 00 1 0 0 0 -1
04 01 1 0 0 0 -1
04 02 1 0 0 0 -1
04 03 1 0 0 0 -1
04 04 1 0 0 0 -1
04 05 1 0 0 0 -1
04 06 1 0 0 0 -1
04 07 1 0 0 0 -1
04 08 1 0 0 0 -1
04 09 1 0 0 0 -1
04 10 1 0 0 0 -1
04 11 1 0 0 0 -1
04 12 1 0 0 0 -1
04 13 1 0 0 0 -1
04 14 1 0 0 0 -1
04 15 1 0 0 0 -1
04 16 1 0 0 0 -1
04 17 1 0 0 0 -1
04 18 1 0 0 0 -1
04 19 1 0 0 0 -1
04 20 1 0 0 0 -1
04 21 1 0 0 0 -1
04 22 1 0 0 0 -1
04 23 1 0 0 0 -1
04 24 1 0 0 0 -1
04 25 1 0 0 0 -1
04 26 1 0 0 0 -1
04 27 1 0 0 0 -1
04 28 1 0 0 0 -1
04 29 1 0 0 0 -1
04 30 1 0 0 0 -1
04 31 1 0 0 0 -1
04 32 1 0 0 0 -1
04 33 1 0 0 0 -1
04 34 1 0 0 0 -1
04 35 1 0 0 0 -1
04 36 1 0 0 0 -1
04 37 1 0 0 0 -1
... 3774 more lines ...
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 1 0 0 0 -1
00 01 1 0 0 0 -1
00 02 1 0 0 0 -1
00 03 1 0 0 0 -1
00 04 1 0 0 0 -1
00 05 1 0 0 0 -1
00 06 1 0 0 0 -1
00 07 1 0 0 0 -1
00 08 1 0 0 0 -1
00 09 1 0 0 0 -1
00 10 1 0 0 0 -1
00 11 1 0 0 0 -1
00 12 1 0 0 0 -1
00 13 1 0 0 0 -1
00 14 1 0 0 0 -1
00 15 1 0 0 0 -1
00 16 1 0 0 0 -1
00 17 1 0 0 0 -1
00 18 1 0 0 0 -1
00 19 1 0 0 0 -1
00 20 1 0 0 0 -1
00 21 1 0 0 0 -1
00 22 1 0 0 0 -1
00 23 1 0 0 0 -1
00 24 1 0 0 0 -1
00 25 1 0 0 0 -1
00 26 1 0 0 0 -1
00 27 1 0 0 0 -1
00 28 1 0 0 0 -1
00 29 1 0 0 0 -1
00 30 1 0 0 0 -1
00 31 1 0 0 0 -1
00 32 1 0 0 0 -1
00 33 1 0 0 0 -1
00 34 1 0 0 0 -1
00 35 1 0 0 0 -1
00 36 1 0 0 0 -1
00 37 1 0 0 0 -1
00 38 1 0 0 0 -1
00 39 1 0 0 0 -1
00 40 1 0 0 0 -1
00 41 1 0 0 0 -1
00 42 1 0 0 0 -1
00 43 1 0 0 0 -1
00 44 1 0 0 0 -1
00 45 1 0 0 0 -1
00 46 1 0 0 0 -1
00 47 1 0 0 0 -1
00 48 1 0 0 0 -1
00 49 1 0 0 0 -1
00 50 1 0 0 0 -1
00 51 1 0 0 0 -1
00 52 1 0 0 0 -1
00 53 1 0 0 0 -1
00 54 1 0 0 0 -1
00 55 1 0 0 0 -1
00 56 1 0 0 0 -1
00 57 1 0 0 0 -1
00 58 1 0 0 0 -1
00 59 1 0 0 0 -1
00 60 1 0 0 0 -1
00 61 1 0 0 0 -1
00 62 1 0 0 0 -1
00 63 1 0 0 0 -1
01 00 1 0 0 0 -1
01 01 1 0 0 0 -1
01 02 1 0 0 0 -1
01 03 1 0 0 0 -1
01 04 1 0 0 0 -1
01 05 1 0 0 0 -1
01 06 1 0 0 0 -1
01 07 1 0 0 0 -1
01 08 1 0 0 0 -1
01 09 1 0 0 0 -1
01 10 1 0 0 0 -1
01 11 1 0 0 0 -1
01 12 1 0 0 0 -1
01 13 1 0 0 0 -1
01 14 1 0 0 0 -1
01 15 1 0 0 0 -1
01 16 1 0 0 0 -1
01 17 1 0 0 0 -1
01 18 1 0 0 0 -1
01 19 1 0 0 0 -1
01 20 1 0 0 0 -1
01 21 1 0 0 0 -1
01 22 1 0 0 0 -1
01 23 1 0 0 0 -1
01 24 1 0 0 0 -1
01 25 1 0 0 0 -1
01 26 1 0 0 0 -1
01 27 1 0 0 0 -1
01 28 1 0 0 0 -1
01 29 1 0 0 0 -1
01 30 1 0 0 0 -1
01 31 1 0 0 0 -1
01 32 1 0 0 0 -1
01 33 1 0 0 0 -1
01 34 1 0 0 0 -1
01 35 1 0 0 0 -1
01 36 1 0 0 0 -1
01 37 1 0 0 0 -1
01 38 1 0 0 0 -1
01 39 1 0 0 0 -1
01 40 1 0 0 0 -1
01 41 1 0 0 0 -1
01 42 1 0 0 0 -1
01 43 1 0 0 0 -1
01 44 1 0 0 0 -1
01 45 1 0 0 0 -1
01 46 1 0 0 0 -1
01 47 1 0 0 0 -1
01 48 1 0 0 0 -1
01 49 1 0 0 0 -1
01 50 1 0 0 0 -1
01 51 1 0 0 0 -1
01 52 1 0 0 0 -1
01 53 1 0 0 0 -1
01 54 1 0 0 0 -1
01 55 1 0 0 0 -1
01 56 1 0 0 0 -1
01 57 1 0 0 0 -1
01 58 1 0 0 0 -1
01 59 1 0 0 0 -1
01 60 1 0 0 0 -1
01 61 1 0 0 0 -1
01 62 1 0 0 0 -1
01 63 1 0 0 0 -1
02 00 1 0 0 0 -1
02 01 1 0 0 0 -1
02 02 1 0 0 0 -1
02 03 1 0 0 0 -1
02 04 1 0 0 0 -1
02 05 1 0 0 0 -1
02 06 1 0 0 0 -1
02 07 1 0 0 0 -1
02 08 1 0 0 0 -1
02 09 1 0 0 0 -1
02 10 1 0 0 0 -1
02 11 1 0 0 0 -1
02 12 1 0 0 0 -1
02 13 1 0 0 0 -1
02 14 1 0 0 0 -1
02 15 1 0 0 0 -1
02 16 1 0 0 0 -1
02 17 1 0 0 0 -1
02 18 1 0 0 0 -1
02 19 1 0 0 0 -1
02 20 1 0 0 0 -1
02 21 1 0 0 0 -1
02 22 1 0 0 0 -1
02 23 1 0 0 0 -1
02 24 1 0 0 0 -1
02 25 1 0 0 0 -1
02 26 1 0 0 0 -1
02 27 1 0 0 0 -1
02 28 1 0 0 0 -1
02 29 1 0 0 0 -1
02 30 1 0 0 0 -1
02 31 1 0 0 0 -1
02 32 1 0 0 0 -1
02 33 1 0 0 0 -1
02 34 1 0 0 0 -1
02 35 1 0 0 0 -1
02 36 1 0 0 0 -1
02 37 1 0 0 0 -1
02 38 1 0 0 0 -1
02 39 1 0 0 0 -1
02 40 1 0 0 0 -1
02 41 1 0 0 0 -1
02 42 1 0 0 0 -1
02 43 1 0 0 0 -1
02 44 1 0 0 0 -1
02 45 1 0 0 0 -1
02 46 1 0 0 0 -1
02 47 1 0 0 0 -1
02 48 1 0 0 0 -1
02 49 1 0 0 0 -1
02 50 1 0 0 0 -1
02 51 1 0 0 0 -1
02 52 1 0 0 0 -1
02 53 1 0 0 0 -1
02 54 1 0 0 0 -1
02 55 1 0 0 0 -1
02 56 1 0 0 0 -1
02 57 1 0 0 0 -1
02 58 1 0 0 0 -1
02 59 1 0 0 0 -1
02 60 1 0 0 0 -1
02 61 1 0 0 0 -1
02 62 1 0 0 0 -1
02 63 1 0 0 0 -1
03 00 1 0 0 0 -1
03 01 1 0 0 0 -1
03 02 1 0 0 0 -1
03 03 1 0 0 0 -1
03 04 1 0 0 0 -1
03 05 1 0 0 0 -1
03 06 1 0 0 0 -1
03 07 1 0 0 0 -1
03 08 1 0 0 0 -1
03 09 1 0 0 0 -1
03 10 1 0 0 0 -1
03 11 1 0 0 0 -1
03 12 1 0 0 0 -1
03 13 1 0 0 0 -1
03 14 1 0 0 0 -1
03 15 1 0 0 0 -1
03 16 1 0 0 0 -1
03 17 1 0 0 0 -1
03 18 1 0 0 0 -1
03 19 1 0 0 0 -1
03 20 1 0 0 0 -1
03 21 1 0 0 0 -1
03 22 1 0 0 0 -1
03 23 1 0 0 0 -1
03 24 1 0 0 0 -1
03 25 1 0 0 0 -1
03 26 1 0 0 0 -1
03 27 1 0 0 0 -1
03 28 1 0 0 0 -1
03 29 1 0 0 0 -1
03 30 1 0 0 0 -1
03 31 1 0 0 0 -1
03 32 1 0 0 0 -1
03 33 1 0 0 0 -1
03 34 1 0 0 0 -1
03 35 1 0 0 0 -1
03 36 1 0 0 0 -1
03 37 1 0 0 0 -1
03 38 1 0 0 0 -1
03 39 1 0 0 0 -1
03 40 1 0 0 0 -1
03 41 1 0 0 0 -1
03 42 1 0 0 0 -1
03 43 1 0 0 0 -1
03 44 1 0 0 0 -1
03 45 1 0 0 0 -1
03 46 1 0 0 0 -1
03 47 1 0 0 0 -1
03 48 1 0 0 0 -1
03 49 1 0 0 0 -1
03 50 1 0 0 0 -1
03 51 1 0 0 0 -1
03 52 1 0 0 0 -1
03 53 1 0 0 0 -1
03 54 1 0 0 0 -1
03 55 1 0 0 0 -1
03 56 1 0 0 0 -1
03 57 1 0 0 0 -1
03 58 1 0 0 0 -1
03 59 1 0 0 0 -1
03 60 1 0 0 0 -1
03 61 1 0 0 0 -1
03 62 1 0 0 0 -1
03 63 1 0 0 0 -1
04 00 1 0 0 0 -1
04 01 1 0 0 0 -1
04 02 1 0 0 0 -1
04 03 1 0 0 0 -1
04 04 1 0 0 0 -1
04 05 1 0 0 0 -1
04 06 1 0 0 0 -1
04 07 1 0 0 0 -1
04 08 1 0 0 0 -1
04 09 1 0 0 0 -1
04 10 1 0 0 0 -1
04 11 1 0 0 0 -1
04 12 1 0 0 0 -1
04 13 1 0 0 0 -1
04 14 1 0 0 0 -1
04 15 1 0 0 0 -1
04 16 1 0 0 0 -1
04 17 1 0 0 0 -1
04 18 1 0 0 0 -1
04 19 1 0 0 0 -1
04 20 1 0 0 0 -1
04 21 1 0 0 0 -1
04 22 1 0 0 0 -1
04 23 1 0 0 0 -1
04 24 1 0 0 0 -1
04 25 1 0 0 0 -1
04 26 1 0 0 0 -1
04 27 1 0 0 0 -1
04 28 1 0 0 0 -1
04 29 1 0 0 0 -1
04 30 1 0 0 0 -1
04 31 1 0 0 0 -1
04 32 1 0 0 0 -1
04 33 1 0 0 0 -1
04 34 1 0 0 0 -1
04 35 1 0 0 0 -1
04 36 1 0 0 0 -1
04 37 1 0 0 0 -1
... 3774 more lines ...
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/run$6R_mpw3$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 100
STOP_COLUMN = 224
WAIT_FOR_FPGA = 1
CONFIG_ID = 9
ELOG_CATEGORY = Beam # Debug, Beam, VoltageScan, Scan
COMMENT_IN_CONF = "Comment here"
ELOG_OUTPUT_PATH = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs"
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
35
|
Wed Jul 5 11:31:50 2023 |
tb-crew | searching correlations | 638 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 05.07.2023 10:56:24 | 05.07.2023 11:27:40 | 31 |
automatic log for run 638
Comment:
running with base & piggy
Only very few pixel active |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.35
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 1 0 0 0 -1
00 01 1 0 0 0 -1
00 02 1 0 0 0 -1
00 03 1 0 0 0 -1
00 04 1 0 0 0 -1
00 05 1 0 0 0 -1
00 06 1 0 0 0 -1
00 07 1 0 0 0 -1
00 08 1 0 0 0 -1
00 09 1 0 0 0 -1
00 10 1 0 0 0 -1
00 11 1 0 0 0 -1
00 12 1 0 0 0 -1
00 13 1 0 0 0 -1
00 14 1 0 0 0 -1
00 15 1 0 0 0 -1
00 16 1 0 0 0 -1
00 17 1 0 0 0 -1
00 18 1 0 0 0 -1
00 19 1 0 0 0 -1
00 20 1 0 0 0 -1
00 21 1 0 0 0 -1
00 22 1 0 0 0 -1
00 23 1 0 0 0 -1
00 24 1 0 0 0 -1
00 25 1 0 0 0 -1
00 26 1 0 0 0 -1
00 27 1 0 0 0 -1
00 28 1 0 0 0 -1
00 29 1 0 0 0 -1
00 30 1 0 0 0 -1
00 31 1 0 0 0 -1
00 32 1 0 0 0 -1
00 33 1 0 0 0 -1
00 34 1 0 0 0 -1
00 35 1 0 0 0 -1
00 36 1 0 0 0 -1
00 37 1 0 0 0 -1
00 38 1 0 0 0 -1
00 39 1 0 0 0 -1
00 40 1 0 0 0 -1
00 41 1 0 0 0 -1
00 42 1 0 0 0 -1
00 43 1 0 0 0 -1
00 44 1 0 0 0 -1
00 45 1 0 0 0 -1
00 46 1 0 0 0 -1
00 47 1 0 0 0 -1
00 48 1 0 0 0 -1
00 49 1 0 0 0 -1
00 50 1 0 0 0 -1
00 51 1 0 0 0 -1
00 52 1 0 0 0 -1
00 53 1 0 0 0 -1
00 54 1 0 0 0 -1
00 55 1 0 0 0 -1
00 56 1 0 0 0 -1
00 57 1 0 0 0 -1
00 58 1 0 0 0 -1
00 59 1 0 0 0 -1
00 60 1 0 0 0 -1
00 61 1 0 0 0 -1
00 62 1 0 0 0 -1
00 63 1 0 0 0 -1
01 00 1 0 0 0 -1
01 01 1 0 0 0 -1
01 02 1 0 0 0 -1
01 03 1 0 0 0 -1
01 04 1 0 0 0 -1
01 05 1 0 0 0 -1
01 06 1 0 0 0 -1
01 07 1 0 0 0 -1
01 08 1 0 0 0 -1
01 09 1 0 0 0 -1
01 10 1 0 0 0 -1
01 11 1 0 0 0 -1
01 12 1 0 0 0 -1
01 13 1 0 0 0 -1
01 14 1 0 0 0 -1
01 15 1 0 0 0 -1
01 16 1 0 0 0 -1
01 17 1 0 0 0 -1
01 18 1 0 0 0 -1
01 19 1 0 0 0 -1
01 20 1 0 0 0 -1
01 21 1 0 0 0 -1
01 22 1 0 0 0 -1
01 23 1 0 0 0 -1
01 24 1 0 0 0 -1
01 25 1 0 0 0 -1
01 26 1 0 0 0 -1
01 27 1 0 0 0 -1
01 28 1 0 0 0 -1
01 29 1 0 0 0 -1
01 30 1 0 0 0 -1
01 31 1 0 0 0 -1
01 32 1 0 0 0 -1
01 33 1 0 0 0 -1
01 34 1 0 0 0 -1
01 35 1 0 0 0 -1
01 36 1 0 0 0 -1
01 37 1 0 0 0 -1
01 38 1 0 0 0 -1
01 39 1 0 0 0 -1
01 40 1 0 0 0 -1
01 41 1 0 0 0 -1
01 42 1 0 0 0 -1
01 43 1 0 0 0 -1
01 44 1 0 0 0 -1
01 45 1 0 0 0 -1
01 46 1 0 0 0 -1
01 47 1 0 0 0 -1
01 48 1 0 0 0 -1
01 49 1 0 0 0 -1
01 50 1 0 0 0 -1
01 51 1 0 0 0 -1
01 52 1 0 0 0 -1
01 53 1 0 0 0 -1
01 54 1 0 0 0 -1
01 55 1 0 0 0 -1
01 56 1 0 0 0 -1
01 57 1 0 0 0 -1
01 58 1 0 0 0 -1
01 59 1 0 0 0 -1
01 60 1 0 0 0 -1
01 61 1 0 0 0 -1
01 62 1 0 0 0 -1
01 63 1 0 0 0 -1
02 00 1 0 0 0 -1
02 01 1 0 0 0 -1
02 02 1 0 0 0 -1
02 03 1 0 0 0 -1
02 04 1 0 0 0 -1
02 05 1 0 0 0 -1
02 06 1 0 0 0 -1
02 07 1 0 0 0 -1
02 08 1 0 0 0 -1
02 09 1 0 0 0 -1
02 10 1 0 0 0 -1
02 11 1 0 0 0 -1
02 12 1 0 0 0 -1
02 13 1 0 0 0 -1
02 14 1 0 0 0 -1
02 15 1 0 0 0 -1
02 16 1 0 0 0 -1
02 17 1 0 0 0 -1
02 18 1 0 0 0 -1
02 19 1 0 0 0 -1
02 20 1 0 0 0 -1
02 21 1 0 0 0 -1
02 22 1 0 0 0 -1
02 23 1 0 0 0 -1
02 24 1 0 0 0 -1
02 25 1 0 0 0 -1
02 26 1 0 0 0 -1
02 27 1 0 0 0 -1
02 28 1 0 0 0 -1
02 29 1 0 0 0 -1
02 30 1 0 0 0 -1
02 31 1 0 0 0 -1
02 32 1 0 0 0 -1
02 33 1 0 0 0 -1
02 34 1 0 0 0 -1
02 35 1 0 0 0 -1
02 36 1 0 0 0 -1
02 37 1 0 0 0 -1
02 38 1 0 0 0 -1
02 39 1 0 0 0 -1
02 40 1 0 0 0 -1
02 41 1 0 0 0 -1
02 42 1 0 0 0 -1
02 43 1 0 0 0 -1
02 44 1 0 0 0 -1
02 45 1 0 0 0 -1
02 46 1 0 0 0 -1
02 47 1 0 0 0 -1
02 48 1 0 0 0 -1
02 49 1 0 0 0 -1
02 50 1 0 0 0 -1
02 51 1 0 0 0 -1
02 52 1 0 0 0 -1
02 53 1 0 0 0 -1
02 54 1 0 0 0 -1
02 55 1 0 0 0 -1
02 56 1 0 0 0 -1
02 57 1 0 0 0 -1
02 58 1 0 0 0 -1
02 59 1 0 0 0 -1
02 60 1 0 0 0 -1
02 61 1 0 0 0 -1
02 62 1 0 0 0 -1
02 63 1 0 0 0 -1
03 00 1 0 0 0 -1
03 01 1 0 0 0 -1
03 02 1 0 0 0 -1
03 03 1 0 0 0 -1
03 04 1 0 0 0 -1
03 05 1 0 0 0 -1
03 06 1 0 0 0 -1
03 07 1 0 0 0 -1
03 08 1 0 0 0 -1
03 09 1 0 0 0 -1
03 10 1 0 0 0 -1
03 11 1 0 0 0 -1
03 12 1 0 0 0 -1
03 13 1 0 0 0 -1
03 14 1 0 0 0 -1
03 15 1 0 0 0 -1
03 16 1 0 0 0 -1
03 17 1 0 0 0 -1
03 18 1 0 0 0 -1
03 19 1 0 0 0 -1
03 20 1 0 0 0 -1
03 21 1 0 0 0 -1
03 22 1 0 0 0 -1
03 23 1 0 0 0 -1
03 24 1 0 0 0 -1
03 25 1 0 0 0 -1
03 26 1 0 0 0 -1
03 27 1 0 0 0 -1
03 28 1 0 0 0 -1
03 29 1 0 0 0 -1
03 30 1 0 0 0 -1
03 31 1 0 0 0 -1
03 32 1 0 0 0 -1
03 33 1 0 0 0 -1
03 34 1 0 0 0 -1
03 35 1 0 0 0 -1
03 36 1 0 0 0 -1
03 37 1 0 0 0 -1
03 38 1 0 0 0 -1
03 39 1 0 0 0 -1
03 40 1 0 0 0 -1
03 41 1 0 0 0 -1
03 42 1 0 0 0 -1
03 43 1 0 0 0 -1
03 44 1 0 0 0 -1
03 45 1 0 0 0 -1
03 46 1 0 0 0 -1
03 47 1 0 0 0 -1
03 48 1 0 0 0 -1
03 49 1 0 0 0 -1
03 50 1 0 0 0 -1
03 51 1 0 0 0 -1
03 52 1 0 0 0 -1
03 53 1 0 0 0 -1
03 54 1 0 0 0 -1
03 55 1 0 0 0 -1
03 56 1 0 0 0 -1
03 57 1 0 0 0 -1
03 58 1 0 0 0 -1
03 59 1 0 0 0 -1
03 60 1 0 0 0 -1
03 61 1 0 0 0 -1
03 62 1 0 0 0 -1
03 63 1 0 0 0 -1
04 00 1 0 0 0 -1
04 01 1 0 0 0 -1
04 02 1 0 0 0 -1
04 03 1 0 0 0 -1
04 04 1 0 0 0 -1
04 05 1 0 0 0 -1
04 06 1 0 0 0 -1
04 07 1 0 0 0 -1
04 08 1 0 0 0 -1
04 09 1 0 0 0 -1
04 10 1 0 0 0 -1
04 11 1 0 0 0 -1
04 12 1 0 0 0 -1
04 13 1 0 0 0 -1
04 14 1 0 0 0 -1
04 15 1 0 0 0 -1
04 16 1 0 0 0 -1
04 17 1 0 0 0 -1
04 18 1 0 0 0 -1
04 19 1 0 0 0 -1
04 20 1 0 0 0 -1
04 21 1 0 0 0 -1
04 22 1 0 0 0 -1
04 23 1 0 0 0 -1
04 24 1 0 0 0 -1
04 25 1 0 0 0 -1
04 26 1 0 0 0 -1
04 27 1 0 0 0 -1
04 28 1 0 0 0 -1
04 29 1 0 0 0 -1
04 30 1 0 0 0 -1
04 31 1 0 0 0 -1
04 32 1 0 0 0 -1
04 33 1 0 0 0 -1
04 34 1 0 0 0 -1
04 35 1 0 0 0 -1
04 36 1 0 0 0 -1
04 37 1 0 0 0 -1
... 3774 more lines ...
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 1 0 0 0 -1
00 01 1 0 0 0 -1
00 02 1 0 0 0 -1
00 03 1 0 0 0 -1
00 04 1 0 0 0 -1
00 05 1 0 0 0 -1
00 06 1 0 0 0 -1
00 07 1 0 0 0 -1
00 08 1 0 0 0 -1
00 09 1 0 0 0 -1
00 10 1 0 0 0 -1
00 11 1 0 0 0 -1
00 12 1 0 0 0 -1
00 13 1 0 0 0 -1
00 14 1 0 0 0 -1
00 15 1 0 0 0 -1
00 16 1 0 0 0 -1
00 17 1 0 0 0 -1
00 18 1 0 0 0 -1
00 19 1 0 0 0 -1
00 20 1 0 0 0 -1
00 21 1 0 0 0 -1
00 22 1 0 0 0 -1
00 23 1 0 0 0 -1
00 24 1 0 0 0 -1
00 25 1 0 0 0 -1
00 26 1 0 0 0 -1
00 27 1 0 0 0 -1
00 28 1 0 0 0 -1
00 29 1 0 0 0 -1
00 30 1 0 0 0 -1
00 31 1 0 0 0 -1
00 32 1 0 0 0 -1
00 33 1 0 0 0 -1
00 34 1 0 0 0 -1
00 35 1 0 0 0 -1
00 36 1 0 0 0 -1
00 37 1 0 0 0 -1
00 38 1 0 0 0 -1
00 39 1 0 0 0 -1
00 40 1 0 0 0 -1
00 41 1 0 0 0 -1
00 42 1 0 0 0 -1
00 43 1 0 0 0 -1
00 44 1 0 0 0 -1
00 45 1 0 0 0 -1
00 46 1 0 0 0 -1
00 47 1 0 0 0 -1
00 48 1 0 0 0 -1
00 49 1 0 0 0 -1
00 50 1 0 0 0 -1
00 51 1 0 0 0 -1
00 52 1 0 0 0 -1
00 53 1 0 0 0 -1
00 54 1 0 0 0 -1
00 55 1 0 0 0 -1
00 56 1 0 0 0 -1
00 57 1 0 0 0 -1
00 58 1 0 0 0 -1
00 59 1 0 0 0 -1
00 60 1 0 0 0 -1
00 61 1 0 0 0 -1
00 62 1 0 0 0 -1
00 63 1 0 0 0 -1
01 00 1 0 0 0 -1
01 01 1 0 0 0 -1
01 02 1 0 0 0 -1
01 03 1 0 0 0 -1
01 04 1 0 0 0 -1
01 05 1 0 0 0 -1
01 06 1 0 0 0 -1
01 07 1 0 0 0 -1
01 08 1 0 0 0 -1
01 09 1 0 0 0 -1
01 10 1 0 0 0 -1
01 11 1 0 0 0 -1
01 12 1 0 0 0 -1
01 13 1 0 0 0 -1
01 14 1 0 0 0 -1
01 15 1 0 0 0 -1
01 16 1 0 0 0 -1
01 17 1 0 0 0 -1
01 18 1 0 0 0 -1
01 19 1 0 0 0 -1
01 20 1 0 0 0 -1
01 21 1 0 0 0 -1
01 22 1 0 0 0 -1
01 23 1 0 0 0 -1
01 24 1 0 0 0 -1
01 25 1 0 0 0 -1
01 26 1 0 0 0 -1
01 27 1 0 0 0 -1
01 28 1 0 0 0 -1
01 29 1 0 0 0 -1
01 30 1 0 0 0 -1
01 31 1 0 0 0 -1
01 32 1 0 0 0 -1
01 33 1 0 0 0 -1
01 34 1 0 0 0 -1
01 35 1 0 0 0 -1
01 36 1 0 0 0 -1
01 37 1 0 0 0 -1
01 38 1 0 0 0 -1
01 39 1 0 0 0 -1
01 40 1 0 0 0 -1
01 41 1 0 0 0 -1
01 42 1 0 0 0 -1
01 43 1 0 0 0 -1
01 44 1 0 0 0 -1
01 45 1 0 0 0 -1
01 46 1 0 0 0 -1
01 47 1 0 0 0 -1
01 48 1 0 0 0 -1
01 49 1 0 0 0 -1
01 50 1 0 0 0 -1
01 51 1 0 0 0 -1
01 52 1 0 0 0 -1
01 53 1 0 0 0 -1
01 54 1 0 0 0 -1
01 55 1 0 0 0 -1
01 56 1 0 0 0 -1
01 57 1 0 0 0 -1
01 58 1 0 0 0 -1
01 59 1 0 0 0 -1
01 60 1 0 0 0 -1
01 61 1 0 0 0 -1
01 62 1 0 0 0 -1
01 63 1 0 0 0 -1
02 00 1 0 0 0 -1
02 01 1 0 0 0 -1
02 02 1 0 0 0 -1
02 03 1 0 0 0 -1
02 04 1 0 0 0 -1
02 05 1 0 0 0 -1
02 06 1 0 0 0 -1
02 07 1 0 0 0 -1
02 08 1 0 0 0 -1
02 09 1 0 0 0 -1
02 10 1 0 0 0 -1
02 11 1 0 0 0 -1
02 12 1 0 0 0 -1
02 13 1 0 0 0 -1
02 14 1 0 0 0 -1
02 15 1 0 0 0 -1
02 16 1 0 0 0 -1
02 17 1 0 0 0 -1
02 18 1 0 0 0 -1
02 19 1 0 0 0 -1
02 20 1 0 0 0 -1
02 21 1 0 0 0 -1
02 22 1 0 0 0 -1
02 23 1 0 0 0 -1
02 24 1 0 0 0 -1
02 25 1 0 0 0 -1
02 26 1 0 0 0 -1
02 27 1 0 0 0 -1
02 28 1 0 0 0 -1
02 29 1 0 0 0 -1
02 30 1 0 0 0 -1
02 31 1 0 0 0 -1
02 32 1 0 0 0 -1
02 33 1 0 0 0 -1
02 34 1 0 0 0 -1
02 35 1 0 0 0 -1
02 36 1 0 0 0 -1
02 37 1 0 0 0 -1
02 38 1 0 0 0 -1
02 39 1 0 0 0 -1
02 40 1 0 0 0 -1
02 41 1 0 0 0 -1
02 42 1 0 0 0 -1
02 43 1 0 0 0 -1
02 44 1 0 0 0 -1
02 45 1 0 0 0 -1
02 46 1 0 0 0 -1
02 47 1 0 0 0 -1
02 48 1 0 0 0 -1
02 49 1 0 0 0 -1
02 50 1 0 0 0 -1
02 51 1 0 0 0 -1
02 52 1 0 0 0 -1
02 53 1 0 0 0 -1
02 54 1 0 0 0 -1
02 55 1 0 0 0 -1
02 56 1 0 0 0 -1
02 57 1 0 0 0 -1
02 58 1 0 0 0 -1
02 59 1 0 0 0 -1
02 60 1 0 0 0 -1
02 61 1 0 0 0 -1
02 62 1 0 0 0 -1
02 63 1 0 0 0 -1
03 00 1 0 0 0 -1
03 01 1 0 0 0 -1
03 02 1 0 0 0 -1
03 03 1 0 0 0 -1
03 04 1 0 0 0 -1
03 05 1 0 0 0 -1
03 06 1 0 0 0 -1
03 07 1 0 0 0 -1
03 08 1 0 0 0 -1
03 09 1 0 0 0 -1
03 10 1 0 0 0 -1
03 11 1 0 0 0 -1
03 12 1 0 0 0 -1
03 13 1 0 0 0 -1
03 14 1 0 0 0 -1
03 15 1 0 0 0 -1
03 16 1 0 0 0 -1
03 17 1 0 0 0 -1
03 18 1 0 0 0 -1
03 19 1 0 0 0 -1
03 20 1 0 0 0 -1
03 21 1 0 0 0 -1
03 22 1 0 0 0 -1
03 23 1 0 0 0 -1
03 24 1 0 0 0 -1
03 25 1 0 0 0 -1
03 26 1 0 0 0 -1
03 27 1 0 0 0 -1
03 28 1 0 0 0 -1
03 29 1 0 0 0 -1
03 30 1 0 0 0 -1
03 31 1 0 0 0 -1
03 32 1 0 0 0 -1
03 33 1 0 0 0 -1
03 34 1 0 0 0 -1
03 35 1 0 0 0 -1
03 36 1 0 0 0 -1
03 37 1 0 0 0 -1
03 38 1 0 0 0 -1
03 39 1 0 0 0 -1
03 40 1 0 0 0 -1
03 41 1 0 0 0 -1
03 42 1 0 0 0 -1
03 43 1 0 0 0 -1
03 44 1 0 0 0 -1
03 45 1 0 0 0 -1
03 46 1 0 0 0 -1
03 47 1 0 0 0 -1
03 48 1 0 0 0 -1
03 49 1 0 0 0 -1
03 50 1 0 0 0 -1
03 51 1 0 0 0 -1
03 52 1 0 0 0 -1
03 53 1 0 0 0 -1
03 54 1 0 0 0 -1
03 55 1 0 0 0 -1
03 56 1 0 0 0 -1
03 57 1 0 0 0 -1
03 58 1 0 0 0 -1
03 59 1 0 0 0 -1
03 60 1 0 0 0 -1
03 61 1 0 0 0 -1
03 62 1 0 0 0 -1
03 63 1 0 0 0 -1
04 00 1 0 0 0 -1
04 01 1 0 0 0 -1
04 02 1 0 0 0 -1
04 03 1 0 0 0 -1
04 04 1 0 0 0 -1
04 05 1 0 0 0 -1
04 06 1 0 0 0 -1
04 07 1 0 0 0 -1
04 08 1 0 0 0 -1
04 09 1 0 0 0 -1
04 10 1 0 0 0 -1
04 11 1 0 0 0 -1
04 12 1 0 0 0 -1
04 13 1 0 0 0 -1
04 14 1 0 0 0 -1
04 15 1 0 0 0 -1
04 16 1 0 0 0 -1
04 17 1 0 0 0 -1
04 18 1 0 0 0 -1
04 19 1 0 0 0 -1
04 20 1 0 0 0 -1
04 21 1 0 0 0 -1
04 22 1 0 0 0 -1
04 23 1 0 0 0 -1
04 24 1 0 0 0 -1
04 25 1 0 0 0 -1
04 26 1 0 0 0 -1
04 27 1 0 0 0 -1
04 28 1 0 0 0 -1
04 29 1 0 0 0 -1
04 30 1 0 0 0 -1
04 31 1 0 0 0 -1
04 32 1 0 0 0 -1
04 33 1 0 0 0 -1
04 34 1 0 0 0 -1
04 35 1 0 0 0 -1
04 36 1 0 0 0 -1
04 37 1 0 0 0 -1
... 3774 more lines ...
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/run$6R_mpw3$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 100
STOP_COLUMN = 224
WAIT_FOR_FPGA = 1
CONFIG_ID = 9
ELOG_CATEGORY = Beam # Debug, Beam, VoltageScan, Scan
COMMENT_IN_CONF = "Comment here"
ELOG_OUTPUT_PATH = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs"
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
32
|
Tue Jul 4 21:08:22 2023 |
tb-crew | searching correlations | 621 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 04.07.2023 18:52:11 | 04.07.2023 21:04:14 | 132 |
automatic log for run 621
Comment: |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.35
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 100
STOP_COLUMN = 224
WAIT_FOR_FPGA = 1
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
31
|
Tue Jul 4 18:45:25 2023 |
tb-crew | searching correlations | 620 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 04.07.2023 18:22:31 | 04.07.2023 18:41:17 | 18 |
automatic log for run 620
Comment: |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.35
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 100
STOP_COLUMN = 224
WAIT_FOR_FPGA = 1
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
29
|
Tue Jul 4 18:16:49 2023 |
tb-crew | initial tests | 619 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 04.07.2023 18:10:47 | 04.07.2023 18:12:41 | 1 |
automatic log for run 619
Comment: |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.5
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 100
STOP_COLUMN = 224
WAIT_FOR_FPGA = 1
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
28
|
Tue Jul 4 18:09:43 2023 |
tb-crew | initial tests | 617 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 04.07.2023 18:00:40 | 04.07.2023 18:05:36 | 4 |
automatic log for run 617
Comment: |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.5
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 100
STOP_COLUMN = 224
WAIT_FOR_FPGA = 1
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
27
|
Tue Jul 4 17:55:37 2023 |
tb-crew | initial tests | 616 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 04.07.2023 17:41:25 | 04.07.2023 17:51:30 | 10 |
automatic log for run 616
Comment: |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.5
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 100
STOP_COLUMN = 224
WAIT_FOR_FPGA = 1
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
26
|
Tue Jul 4 17:28:24 2023 |
tb-crew | initial tests | 615 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 04.07.2023 17:19:02 | 04.07.2023 17:24:16 | 5 |
automatic log for run 615
Comment: |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.3
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
#DUTIgnoreBusy = 0x2 #no (EUDET mode)
DUTIgnoreBusy = 0xF #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 100
STOP_COLUMN = 224
WAIT_FOR_FPGA = 1
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
25
|
Tue Jul 4 17:18:14 2023 |
tb-crew | initial tests | 614 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 04.07.2023 17:05:10 | 04.07.2023 17:14:07 | 8 |
automatic log for run 614
Comment: |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.3
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 100
STOP_COLUMN = 224
WAIT_FOR_FPGA = 1
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
24
|
Tue Jul 4 16:46:57 2023 |
tb-crew | initial tests | 613 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 04.07.2023 16:38:06 | 04.07.2023 16:42:49 | 4 |
automatic log for run 613
Comment: |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.3
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 100
STOP_COLUMN = 224
WAIT_FOR_FPGA = 1
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
23
|
Tue Jul 4 16:39:46 2023 |
tb-crew | initial tests | 612 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 04.07.2023 16:32:51 | 04.07.2023 16:35:38 | 2 |
automatic log for run 612
Comment: |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.3
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 100
STOP_COLUMN = 224
WAIT_FOR_FPGA = 1
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
22
|
Tue Jul 4 16:32:08 2023 |
tb-crew | initial tests | 611 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 04.07.2023 16:25:00 | 04.07.2023 16:28:01 | 3 |
automatic log for run 611
Comment: |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.3
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 100
STOP_COLUMN = 224
WAIT_FOR_FPGA = 1
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
21
|
Tue Jul 4 16:26:06 2023 |
tb-crew | initial tests | 610 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 04.07.2023 16:19:31 | 04.07.2023 16:21:58 | 2 |
automatic log for run 610
Comment: |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.3
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 100
STOP_COLUMN = 224
WAIT_FOR_FPGA = 1
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
19
|
Tue Jul 4 15:14:00 2023 |
tb-crew | initial tests | 602 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 04.07.2023 15:02:58 | 04.07.2023 15:09:53 | 6 |
automatic log for run 602
Comment: |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.3
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 100
STOP_COLUMN = 224
WAIT_FOR_FPGA = 1
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
18
|
Tue Jul 4 15:03:20 2023 |
tb-crew | initial tests | 601 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 04.07.2023 14:51:05 | 04.07.2023 14:59:13 | 8 |
automatic log for run 601
Comment: |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.3
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 100
STOP_COLUMN = 224
WAIT_FOR_FPGA = 1
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
16
|
Tue Jul 4 14:29:01 2023 |
tb-crew | initial tests | 600 | RD50-MPW3 | unknown | | unirradiated | 1.9K | 4.2 | | electron | Unknown | 04.07.2023 14:22:48 | 04.07.2023 14:24:54 | 2 |
automatic log for run 600
Comment: |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 1
enable_readout = 0
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.3
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
piggy_attached = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
|
| Attachment 4: eudaq_config.cfg
|
[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x11
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 500
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/bellevtx01/vtx/tj-monopix2-daq_mx/tj-monopix2-daq/tjmonopix2/scans/output_data/module_0/chip_0/20230703_231744_local_threshold_tuning.h5
#CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/01_Normal_THR30_noisy/20230621_124059_threshold_scan_interpreted.h5
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/20230704_094135_threshold_scan_interpreted.h5
MASKED_PIXELS_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W14R12/03_Normal_THR30/masked_pixels.yaml
CHIP_SN = W14R12
CHIP_CMD_CLK = 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 100
STOP_COLUMN = 224
WAIT_FOR_FPGA = 1
[Producer.hameg]
#HV = 5
BIAS = 5
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|