[RunControl]
EUDAQ_CTRL_PRODUCER_LAST_START = aida_tlu
[LogCollector.log]
[Producer.aida_tlu]
verbose = 0
confid = 20181002
skipconf = 0
# delay start in ms
delayStart = 0
####################################################
# DUT IN/OUTPUT
# Mask: 0 CONT, 1 SPARE, 2 TRIG, 3 BUSY (1 = driven by TLU, 0 = driven by DUT)
# EUDET mode: 7
HDMI1_set = 0x7
HDMI2_set = 0x7
HDMI3_set = 0x7
HDMI4_set = 0x7
# same as above for the clock line, 1 = AIDA mode, 2 = FPGA
HDMI1_clk = 1
HDMI2_clk = 0
HDMI3_clk = 1
HDMI4_clk = 0
LEMOclk = 1 # if input, then also adjust clk.txt
# Activate channels
# Only TLU
#DUTMask = 0x0
# Telescope at HDMI1
#DUTMask = 0x1
# Only FEI4 at HDMI2
#DUTMask = 0x2
# Telescope at HDMI1, FEI4 at HDMI2
#DUTMask = 0x3
#Adenium at HDMI3
#DUTMask = 0x1
#Adenium at HDMI1, MPW3 at HDMI3, Monopix2 at HDMI4
DUTMask = 0xD
# Define mode:
# Each DUT channel has two bits: HDMI1=0&1 bit; HDMI2= 2&3bit; ...
# Only the lowest bit is significant:
# AIDA mode for each "1st" LSbit = 1
# EUDET modes incl. DUT clocking out each "1st" LSbit = 0
# e.g. 1st and 2nd channel in EUDET mode: 0xF0
#DUTMaskMode = 0xF0 # 1st and 2nd channel are reading out Trigger ID
# e.g. only 1st in EUDET mode
#DUTMaskMode = 0xFC # 1st is reading out Trigger ID
#!!!!!!!!!!!! Check this !!!!!!!!!!!!!!!
#DUTMaskMode = 0x01 #I think this is AIDA mode for channel 3 and reading out trigger number
#HDMI3 on AIDA with trigger number
DUTMaskMode = 0x31
# "Mixed mode" to ignore a busy line from a DUT
# TLU ignores the telescope busy (at HDMI1)
#DUTIgnoreBusy = 0x1 # yes (default, Mixed mode)
DUTIgnoreBusy = 0x2 #no (EUDET mode)
###################################################
# ONLY AUTOTRIGGER
#InternalTriggerFreq = 1000
# also set this to 0
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 7 # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 7
in1_DEL = 0
in2_STR = 7
in2_DEL = 0
in3_STR = 7
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# DAC INPUT THRESHOLD in V
DACThreshold0 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold1 = -0.4 # Was -0.04, but we get amplyfied signal from NIM module
DACThreshold2 = -0.20
DACThreshold3 = -0.20
DACThreshold4 = -0.20
DACThreshold5 = -0.20
# PMT Power
PMT1_V = 0.80
PMT2_V = 0.80
PMT3_V = 0.00
PMT4_V = 0.00
# 2 words 32bit: Hi + Lo
# combinations of coincidence are now possible!
# Coincidence of input 0 to 3 (telescope)
#trigMaskHi = 0x00000000
#trigMaskLo = 0x00008000
# Coincidence of input 0 and 1
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008
# New: Coincidence of any 3 of 4, 4 combinations plus all 4
#trigMaskHi = 0x00000000
#trigMaskLo = 0x0000C880
# EUDAQ2
# Define the data collector to be used by the producer
EUDAQ_DC = dc_tlu
[DataCollector.dc_tlu]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=5
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_tlu$X"
DISABLE_PRINT = 1
################################### Adenium #####################################
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=dc_tel
[DataCollector.dc_tel]
EUDAQ_ID=100
EUDAQ_MN=StdEventMonitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION=1
EUDAQ_FW = native
EUDAQ_FW_PATTERN = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_adenium$X"
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/backup/desy_jul23/run$6R_mpw3$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 0
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog_mpw3]
# command (shell script) to execute before starting a run
start_cmd = "./copy_configs.sh"
#files to attach to the Elog entry
files2log = "tmp/peary_config.cfg, tmp/matrix_config_base.txt, tmp/matrix_config_piggy.txt, tmp/eudaq_config.cfg"
################################################ MPX2 #####################################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = dc_mpx2
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
# W08R19
CHIP_CONFIG_FILE = /media/bellevtx01/TOSHIBA EXT/configs/tuning/W08R19/HV_THR25_HVCasc_THR22_10V/20230708_095321_threshold_scan_interpreted.h5
#MASKED_PIXELS_FILE =
CHIP_SN = W08R19
CHIP_CMD_CLK = 160.0
#VCLIP = 100
#IBIAS = 100
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 448
STOP_COLUMN = 512
WAIT_FOR_FPGA = 1
CONFIG_ID = 46
ELOG_CATEGORY = Beam # Debug, Beam, VoltageScan, Scan
COMMENT_IN_CONF = "HV cascode and HV normal, thr 22 and 25, HV = 20V, 0 deg"
ELOG_OUTPUT_PATH = "/media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs"
[Producer.hameg]
HV = 30
BIAS = 1
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.dc_mpx2]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/bellevtx01/TOSHIBA EXT/VTX/data_producer_runs/desy/run$6R_monopix2$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|