# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
#PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
#PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
# 2 words 32bit: Hi + Lo
trigMaskHi = 0x00000000
# combinations of coincidence are now possible!
# Triggering on concidence of scintillator & telepix
#trigMaskLo = 0x00000020 # 0 and 2
#trigMaskLo = 0x00000001 # 0 only
# EXTERNAL TRIGGER INPUTs
# Stretch, delay in 6.25ns ticks
in0_STR = 0x3F # factor to stretch the width of the signal; to get coincidence
in0_DEL = 0 # factor to delay, e.g. compensate
in1_STR = 1
in1_DEL = 0
in2_STR = 0x3F
in2_DEL = 0
in3_STR = 1
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0
in5_DEL = 0
# trigger on rising (0) / falling (1) edge of the trigger input
# Here: all falling edge (scinti) channel 3 rising edge (Telepix)
#trigPol = 0x3B # 111011
trigPol = 0x3E # 111110
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = +0.5 #-0.012
DACThreshold1 = -0.1 #-0.012
DACThreshold2 = -0.5
DACThreshold3 = +0.5
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xB
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xDD
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0x8 #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN=/data1/rd50-mpw4/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[DataCollector.tel_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN=/data1/rd50-mpw4/adenium/adenium_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
voltage_key = "th"
voltage_value = 0.92
[Producer.altel]
EUDAQ_ID=1
EUDAQ_DC=tel_dc
[Producer.MuPix8]
ThPix = 144
#lazyFrog = -25
#register_value = 0
#EUDAQ_DC = tel_dc
[Producer.keithleyPS]
voltage = -200
max_current = 5e-6
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/testbeam_data/desy2404/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw4_mon]
buffer_size = 50000
update_thr = 50
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
voltage = -200
max_current = 5e-6
|