| ID |
Date |
Author |
Subject |
Run Number |
DUT |
Beam Energy |
Rate Setting |
Particle Type |
Data |
t-Start |
t-Stop |
Duration_min |
Frontend |
Phantom |
Phantom thickness |
|
7
|
Fri Mar 14 20:04:41 2025 |
elog-producer | validating setup | 111 | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | 14.03.2025 20:03:34 | 14.03.2025 20:05:07 | 1 | HV | None | | automatic log for run 111
Comment:
bla |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 6 # 0
in0_DEL = 0 # 18
in1_STR = 6 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 10 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x3F #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN="/home/silicon/TJ-Monopix2/testbeam_03_2025/tlu/tlu_run$6R.raw"
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_W02R01]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W02R01_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.10.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W02R01"
chip_sn="W02R01"
online_monitor_port="5500"
[Producer.tjmonopix2_W14R18]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W14R18_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.12.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W14R18"
chip_sn="W14R18"
online_monitor_port="5700"
[Producer.HamegProducer]
hv=20
power_cycle_at_stop=1 #0=False 1=True
logging=1 #0=False 1=True
log_interval=10
logging_directory="/home/silicon/TJ-Monopix2/TJ-Monopix2-Power/Log/testbeam_prep"
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
6
|
Fri Mar 14 19:57:28 2025 |
elog-producer | validating setup | 110 | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | 14.03.2025 19:51:51 | 14.03.2025 19:57:54 | 6 | HV | None | | automatic log for run 110
Comment:
bla |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 6 # 0
in0_DEL = 0 # 18
in1_STR = 6 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 10 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x3F #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN="/home/silicon/TJ-Monopix2/testbeam_03_2025/tlu/tlu_run$6R.raw"
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_W02R01]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W02R01_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.10.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W02R01"
chip_sn="W02R01"
online_monitor_port="5500"
[Producer.tjmonopix2_W14R18]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W14R18_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.12.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W14R18"
chip_sn="W14R18"
online_monitor_port="5700"
[Producer.HamegProducer]
hv=20
power_cycle_at_stop=1 #0=False 1=True
logging=1 #0=False 1=True
log_interval=10
logging_directory="/home/silicon/TJ-Monopix2/TJ-Monopix2-Power/Log/testbeam_prep"
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
71
|
Sat Mar 15 18:37:36 2025 |
RD50 Generic User | Slab Test Water 3cm | 11 | Sandwich-iCT setup(GSI)+RaMon | 205.2 MeV/u | Low Flux Medium | Helium | | 18:41 | 19:28 | 47 | | Plastic Water Slabs | 3cm | RaMon Rate 1.5MHz |
|
85
|
Sat Jun 21 19:54:12 2025 |
Julia Müllner | 124.4 MeV systemtest | 11 | TOF-Cal GSI | 124.4 MeV/u | Low Flux High | Helium | Good | 19:54 | 20:05 | 11 | | | | 16GB collected |
|
5
|
Fri Mar 14 19:50:29 2025 |
elog-producer | validating setup | 109 | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | 14.03.2025 19:49:10 | 14.03.2025 19:50:55 | 1 | HV | None | | automatic log for run 109
Comment:
system tests |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 6 # 0
in0_DEL = 0 # 18
in1_STR = 6 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 10 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x3F #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN="/home/silicon/TJ-Monopix2/testbeam_03_2025/tlu/tlu_run$6R.raw"
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_W02R01]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W02R01_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.10.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W02R01"
chip_sn="W02R01"
online_monitor_port="5500"
[Producer.tjmonopix2_W14R18]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W14R18_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.12.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W14R18"
chip_sn="W14R18"
online_monitor_port="5700"
[Producer.HamegProducer]
hv=20
power_cycle_at_stop=1 #0=False 1=True
logging=1 #0=False 1=True
log_interval=10
logging_directory="/home/silicon/TJ-Monopix2/TJ-Monopix2-Power/Log/testbeam_prep"
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
196
|
Sat Aug 16 21:08:36 2025 |
elog_producer | Castid | 108 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Unknown | 16.08.2025 20:59:05 | 16.08.2025 21:08:39 | 9 | HV | None | | automatic log for run 108
Comment:
self.configure_rx(delay=2, rd_frz_dly=2) (20x) |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #Szinti 4x4cm
PMT2_V= 0.8 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
#InternalTriggerFreq= 5 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.012 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xFF #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
195
|
Sat Aug 16 20:58:19 2025 |
elog_producer | Castid | 107 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Unknown | 16.08.2025 20:47:55 | 16.08.2025 20:58:21 | 10 | HV | None | | automatic log for run 107
Comment:
self.configure_rx(delay=2, rd_frz_dly=2) (20x) |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #Szinti 4x4cm
PMT2_V= 0.8 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
#InternalTriggerFreq= 5 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.012 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xFF #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
194
|
Sat Aug 16 20:47:06 2025 |
elog_producer | Castid | 106 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Unknown | 16.08.2025 20:35:07 | 16.08.2025 20:47:08 | 12 | HV | None | | automatic log for run 106
Comment:
self.configure_rx(delay=2, rd_frz_dly=2) (20x) |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #Szinti 4x4cm
PMT2_V= 0.8 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
#InternalTriggerFreq= 5 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.012 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xFF #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
193
|
Sat Aug 16 20:21:34 2025 |
elog_producer | Castid | 105 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Crap | 16.08.2025 20:21:28 | 16.08.2025 20:21:36 | 0 | HV | None | | automatic log for run 105
Comment:
self.configure_rx(delay=2, rd_frz_dly=2) (20x) |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #Szinti 4x4cm
PMT2_V= 0.8 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
#InternalTriggerFreq= 5 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.012 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xFF #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
192
|
Sat Aug 16 20:19:50 2025 |
elog_producer | Castid | 104 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Crap | 16.08.2025 20:19:46 | 16.08.2025 20:19:52 | 0 | HV | None | | automatic log for run 104
Comment:
self.configure_rx(delay=2, rd_frz_dly=2) (20x) |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #Szinti 4x4cm
PMT2_V= 0.8 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
#InternalTriggerFreq= 5 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.012 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xFF #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
191
|
Sat Aug 16 20:18:49 2025 |
elog_producer | Castid | 103 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Crap | 16.08.2025 20:15:36 | 16.08.2025 20:18:51 | 3 | HV | None | | automatic log for run 103
Comment:
self.configure_rx(delay=2, rd_frz_dly=2) (20x) |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #Szinti 4x4cm
PMT2_V= 0.8 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
#InternalTriggerFreq= 5 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.012 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xFF #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
190
|
Sat Aug 16 20:14:08 2025 |
elog_producer | Castid | 102 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Crap | 16.08.2025 20:10:08 | 16.08.2025 20:14:10 | 4 | HV | None | | automatic log for run 102
Comment:
self.configure_rx(delay=2, rd_frz_dly=2) (20x) |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #Szinti 4x4cm
PMT2_V= 0.8 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
#InternalTriggerFreq= 5 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.012 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xFF #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
189
|
Sat Aug 16 20:07:21 2025 |
elog_producer | Castid | 101 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Unknown | 16.08.2025 20:02:08 | 16.08.2025 20:07:23 | 5 | HV | None | | automatic log for run 101
Comment:
self.configure_rx(delay=10, rd_frz_dly=10) (4x) |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #Szinti 4x4cm
PMT2_V= 0.8 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
#InternalTriggerFreq= 5 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.012 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xFF #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
188
|
Sat Aug 16 20:01:32 2025 |
elog_producer | Castid | 100 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Unknown | 16.08.2025 19:56:31 | 16.08.2025 20:01:35 | 5 | HV | None | | automatic log for run 100
Comment:
self.configure_rx(delay=10, rd_frz_dly=10) (4x) |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #Szinti 4x4cm
PMT2_V= 0.8 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
#InternalTriggerFreq= 5 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.012 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xFF #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
70
|
Sat Mar 15 17:30:18 2025 |
RD50 Generic User | Slab Test Water 2cm | 10 | Sandwich-iCT setup(GSI)+RaMon | 205.2 MeV/u | Low Flux Medium | Helium | | 17:30 | 18:24 | 54 | | Plastic Water Slabs | 2cm | RaMon Rate 1.5 MHz |
|
84
|
Sat Jun 21 19:35:59 2025 |
Julia Müllner | 63.3 MeV systemtest | 10 | TOF-Cal GSI | 63.3 MeV/u | Low Flux High | Helium | Good | 19:37 | 19:53 | 16 | | | | |
|
62
|
Sat Mar 15 08:58:26 2025 |
RD50 Generic User | Alignment Run 800MeV | 1 | Sandwich-iCT setup(GSI)+RaMon | 800 MeV | Low Flux Low | Proton | Good | 07:40 | 08:20 | 40 | | | | RaMon Rate not measured
front sensors 200mu: ~40-60Hz pro Streifen
Comments:
stopped run due to too low rate
|
|
75
|
Sat Jun 21 14:30:29 2025 |
Julia Müllner | 800MeV systemtest | 1 | TOF-Cal GSI | 800 MeV | Low Flux High | Proton | Good | 14:45 | 15:42 | 57 | | | | first spills were done with low flux medium, changed to high at 14:49
again changed to medium at 14:55
again changed to high at 15:00
30 MB pro event builder
last few spills were with the wrong threshold
thresholds were set to 2000 instead of 1000 |
|
1
|
Wed Mar 12 09:29:08 2025 |
tb-crew | validating setup | | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | | | | HV | None | | | 1st test |
|
4
|
Fri Mar 14 19:47:58 2025 |
mausi | validating setup | | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | | | | HV | None | | | system tests |
|