| ID |
Date |
Author |
Subject |
Run Number |
DUT |
Beam Energy |
Rate Setting |
Particle Type |
Data |
t-Start |
t-Stop |
Duration_min |
Frontend |
Phantom |
Phantom thickness |
|
61
|
Sat Mar 15 08:52:52 2025 |
RD50 Generic User | Alignment Run 800MeV | 2 | Sandwich-iCT setup(GSI)+RaMon | 800 MeV | Low Flux Medium | Proton | Good | 08:22 | 9:40 | 78 | | | | RaMon Rate 400kHz
front sensors 200mu: ~10-20kHz pro Streifen
Comments:
In between run, sensors were shifted by 2mm to the left (left and right in online DAQ is mirrored)
|
|
62
|
Sat Mar 15 08:58:26 2025 |
RD50 Generic User | Alignment Run 800MeV | 1 | Sandwich-iCT setup(GSI)+RaMon | 800 MeV | Low Flux Low | Proton | Good | 07:40 | 08:20 | 40 | | | | RaMon Rate not measured
front sensors 200mu: ~40-60Hz pro Streifen
Comments:
stopped run due to too low rate
|
|
63
|
Sat Mar 15 09:51:23 2025 |
RD50 Generic User | Alignment Run 800MeV | 3 | Sandwich-iCT setup(GSI)+RaMon | 800 MeV | Low Flux High | Proton | Unknown | 9:44 | 10:03 | 19 | | | | RaMon Rate 2MHz
front sensors 200mu: ~50-100kHz pro Streifen
Comments:
Factor 10 lost more data than measured
|
|
64
|
Sat Mar 15 10:07:28 2025 |
RD50 Generic User | Alignment Run 252MeV | 4 | Sandwich-iCT setup(GSI)+RaMon | 252.7 MeV | Low Flux Medium | Proton | Good | 10:07 | 11:43 | 96 | | | | RaMon Rate 1MHz
front sensors 200mu: ~10-25kHz pro Streifen |
|
65
|
Sat Mar 15 11:46:28 2025 |
RD50 Generic User | Slab Measurement 145MeV | 5 | Sandwich-iCT setup(GSI)+RaMon | 145.4 MeV | Low Flux Medium | Proton | Good | 11:48 | 13:13 | 85 | | | | RaMon Rate 600kHz
front sensors 200mu: ~1kHz pro Streifen
Comments:
change of the trigger settings inbetween, we saw inefficency on all detectors |
|
75
|
Sat Jun 21 14:30:29 2025 |
Julia Müllner | 800MeV systemtest | 1 | TOF-Cal GSI | 800 MeV | Low Flux High | Proton | Good | 14:45 | 15:42 | 57 | | | | first spills were done with low flux medium, changed to high at 14:49
again changed to medium at 14:55
again changed to high at 15:00
30 MB pro event builder
last few spills were with the wrong threshold
thresholds were set to 2000 instead of 1000 |
|
76
|
Sat Jun 21 15:43:47 2025 |
Julia Müllner | 800MeV systemtest | 2 | TOF-Cal GSI | 800 MeV | Low Flux High | Proton | Good | 16:02 | 16:29 | 27 | | | | Threshold set to 1000
Factor 4 chosen for future runs, 80 GB in total recorded in this run |
|
133
|
Tue Aug 5 14:43:42 2025 |
elog_producer | Castid | | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Crap | | | | HV | None | | | test |
|
134
|
Tue Aug 5 16:02:12 2025 |
elog_producer | Castid | | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Crap | | | | HV | None | | | manual test |
|
135
|
Tue Aug 5 16:03:08 2025 |
elog_producer | Castid | 45 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Crap | 05.08.2025 16:03:03 | 05.08.2025 16:03:36 | 0 | HV | None | | automatic log for run 45
Comment:
auto test |
| Attachment 1: tjmonopix2_tracker.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000010 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 5000 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF3 #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
136
|
Tue Aug 5 16:12:07 2025 |
elog_producer | Castid | | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Crap | | | | HV | None | | | Test debugging tests for debugging to test debugging |
|
137
|
Tue Aug 5 16:13:54 2025 |
elog_producer | Castid | 46 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Crap | 05.08.2025 16:12:04 | 05.08.2025 16:14:21 | 2 | HV | None | | automatic log for run 46
Comment:
Test debugging tests for debugging |
| Attachment 1: tjmonopix2_tracker.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000010 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 5000 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF3 #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
138
|
Tue Aug 5 16:45:37 2025 |
elog_producer | Castid | 47 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Crap | 05.08.2025 16:16:11 | 05.08.2025 16:46:04 | 29 | HV | None | | automatic log for run 47
Comment:
Test debugging tests for debugging |
| Attachment 1: tjmonopix2_tracker.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000010 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 5000 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF3 #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
139
|
Tue Aug 5 17:42:37 2025 |
elog_producer | Castid | 48 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Crap | 05.08.2025 16:59:08 | 05.08.2025 17:43:04 | 43 | HV | None | | automatic log for run 48
Comment: |
| Attachment 1: tjmonopix2_tracker.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000010 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 5000 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF3 #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
140
|
Tue Aug 5 17:49:22 2025 |
elog_producer | Castid | 50 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Crap | 05.08.2025 17:46:44 | 05.08.2025 17:49:50 | 3 | HV | None | | automatic log for run 50
Comment: |
| Attachment 1: tjmonopix2_tracker.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000010 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 5000 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF3 #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
141
|
Tue Aug 5 17:58:32 2025 |
elog_producer | Castid | 51 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Crap | 05.08.2025 17:52:17 | 05.08.2025 17:59:00 | 6 | HV | None | | automatic log for run 51
Comment: |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000010 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 5000 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xFF #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
142
|
Sat Aug 16 14:41:43 2025 |
elog_producer | Castid | 52 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Crap | 16.08.2025 14:41:28 | 16.08.2025 14:41:45 | 0 | HV | None | | automatic log for run 52
Comment: |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000010 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 5000 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xFF #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
143
|
Sat Aug 16 14:50:38 2025 |
elog_producer | Castid | 53 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Crap | 16.08.2025 14:43:57 | 16.08.2025 14:50:40 | 6 | HV | None | | automatic log for run 53
Comment: |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000010 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
# InternalTriggerFreq= 5000 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xFF #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
144
|
Sat Aug 16 14:55:11 2025 |
elog_producer | Castid | 54 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Unknown | 16.08.2025 14:52:47 | 16.08.2025 14:55:13 | 2 | HV | None | | automatic log for run 54
Comment:
Testrun with beam, TLU does not trigger but monopixes should be fine... |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000010 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
# InternalTriggerFreq= 5000 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xFF #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
145
|
Sat Aug 16 15:01:51 2025 |
elog_producer | Castid | 55 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Unknown | 16.08.2025 14:59:10 | 16.08.2025 15:01:52 | 2 | HV | None | | automatic log for run 55
Comment:
Testrun with beam, TLU does not trigger but monopixes should be fine... |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000010 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
# InternalTriggerFreq= 5000 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xFF #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|