| ID |
Date |
Author |
Subject |
Run Number |
DUT |
Beam Energy |
Rate Setting |
Particle Type |
Data |
t-Start |
t-Stop |
Duration_min |
Frontend |
Phantom |
Phantom thickness |
|
244
|
Sat Sep 20 21:12:30 2025 |
elog_producer | Caribou 1.5 | 1042 | RD50-MPW4 | 800 MeV | Low Flux High | Proton | Unknown | 20.09.2025 21:11:57 | 20.09.2025 21:12:41 | 0 | Normal | | | automatic log for run 1042
Comment:
DMA debugging |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 1
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/dma/dma_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -190
[Producer.tracker_irgendwas]
|
|
243
|
Sat Sep 20 21:02:14 2025 |
elog_producer | Caribou 1.5 | 1041 | RD50-MPW4 | 800 MeV | Low Flux High | Proton | Unknown | 20.09.2025 21:01:34 | 20.09.2025 21:02:26 | 0 | Normal | | | automatic log for run 1041
Comment:
no data from DMA  |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 1
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/dma/dma_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -190
[Producer.tracker_irgendwas]
|
|
239
|
Sat Sep 20 20:58:41 2025 |
elog_producer | Caribou 1.5 | 1040 | RD50-MPW4 | 800 MeV | Low Flux High | Proton | Unknown | 20.09.2025 20:51:57 | 20.09.2025 20:58:53 | 6 | Normal | | | automatic log for run 1040
Comment:
this time no RX drops |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -190
[Producer.tracker_irgendwas]
|
|
236
|
Sat Sep 20 20:40:06 2025 |
elog_producer | Caribou 1.5 | 1038 | RD50-MPW4 | 800 MeV | Low Flux High | Proton | Unknown | 20.09.2025 20:34:31 | 20.09.2025 20:40:18 | 5 | Normal | | | automatic log for run 1038
Comment: |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -190
[Producer.tracker_irgendwas]
|
|
234
|
Sat Sep 20 20:32:10 2025 |
elog_producer | Caribou 1.5 | 1037 | RD50-MPW4 | 800 MeV | Low Flux Medium | Proton | Unknown | 20.09.2025 20:27:14 | 20.09.2025 20:32:22 | 5 | Normal | | | automatic log for run 1037
Comment:
higher rates |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -190
[Producer.tracker_irgendwas]
|
|
233
|
Sat Sep 20 20:26:50 2025 |
elog_producer | Caribou 1.5 | 1036 | RD50-MPW4 | 800 MeV | Low Flux Medium | Proton | Unknown | 20.09.2025 20:21:48 | 20.09.2025 20:27:01 | 5 | Normal | | | automatic log for run 1036
Comment:
higher rates |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -190
[Producer.tracker_irgendwas]
|
|
231
|
Sat Sep 20 20:17:25 2025 |
elog_producer | Caribou 1.5 | 1035 | RD50-MPW4 | 800 MeV | Low Flux Low | Proton | Unknown | 20.09.2025 20:12:26 | 20.09.2025 20:17:36 | 5 | Normal | | | automatic log for run 1035
Comment:
bias voltage low voltages |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -18
[Producer.tracker_irgendwas]
|
|
230
|
Sat Sep 20 20:11:08 2025 |
elog_producer | Caribou 1.5 | 1034 | RD50-MPW4 | 800 MeV | Low Flux Low | Proton | Unknown | 20.09.2025 20:06:08 | 20.09.2025 20:11:19 | 5 | Normal | | | automatic log for run 1034
Comment:
bias voltage low voltages |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -15
[Producer.tracker_irgendwas]
|
|
229
|
Sat Sep 20 20:04:05 2025 |
elog_producer | Caribou 1.5 | 1033 | RD50-MPW4 | 800 MeV | Low Flux Low | Proton | Unknown | 20.09.2025 19:58:43 | 20.09.2025 20:04:17 | 5 | Normal | | | automatic log for run 1033
Comment:
bias voltage low voltages |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -12
[Producer.tracker_irgendwas]
|
|
228
|
Sat Sep 20 19:57:10 2025 |
elog_producer | Caribou 1.5 | 1032 | RD50-MPW4 | 800 MeV | Low Flux Low | Proton | Unknown | 20.09.2025 19:51:04 | 20.09.2025 19:57:22 | 6 | Normal | | | automatic log for run 1032
Comment:
bias voltage low voltages |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -160
[Producer.tracker_irgendwas]
|
|
225
|
Sat Sep 20 19:49:27 2025 |
elog_producer | Caribou 1.5 | 1031 | RD50-MPW4 | 800 MeV | Low Flux Low | Proton | Unknown | 20.09.2025 19:44:43 | 20.09.2025 19:49:39 | 4 | Normal | | | automatic log for run 1031
Comment:
bias voltage scan |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -150
[Producer.tracker_irgendwas]
|
|
224
|
Sat Sep 20 19:43:31 2025 |
elog_producer | Caribou 1.5 | 1030 | RD50-MPW4 | 800 MeV | Low Flux Low | Proton | Unknown | 20.09.2025 19:34:17 | 20.09.2025 19:43:41 | 9 | Normal | | | automatic log for run 1030
Comment:
bias voltage scan |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -140
[Producer.tracker_irgendwas]
|
|
223
|
Sat Sep 20 19:32:53 2025 |
elog_producer | Caribou 1.5 | 1029 | RD50-MPW4 | 800 MeV | Low Flux Low | Proton | Unknown | 20.09.2025 19:28:00 | 20.09.2025 19:33:05 | 5 | Normal | | | automatic log for run 1029
Comment:
bias voltage scan |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -130
[Producer.tracker_irgendwas]
|
|
222
|
Sat Sep 20 19:26:22 2025 |
elog_producer | Caribou 1.5 | 1028 | RD50-MPW4 | 800 MeV | Low Flux Low | Proton | Unknown | 20.09.2025 19:21:29 | 20.09.2025 19:26:33 | 5 | Normal | | | automatic log for run 1028
Comment:
bias voltage scan |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -120
[Producer.tracker_irgendwas]
|
|
221
|
Sat Sep 20 19:20:08 2025 |
elog_producer | Caribou 1.5 | 1027 | RD50-MPW4 | 800 MeV | Low Flux Low | Proton | Unknown | 20.09.2025 19:15:16 | 20.09.2025 19:20:19 | 5 | Normal | | | automatic log for run 1027
Comment:
bias voltage scan |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -110
[Producer.tracker_irgendwas]
|
|
220
|
Sat Sep 20 19:14:00 2025 |
elog_producer | Caribou 1.5 | 1026 | RD50-MPW4 | 800 MeV | Low Flux Low | Proton | Unknown | 20.09.2025 19:09:07 | 20.09.2025 19:14:12 | 5 | Normal | | | automatic log for run 1026
Comment:
bias voltage scan |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -100
[Producer.tracker_irgendwas]
|
|
219
|
Sat Sep 20 19:07:43 2025 |
elog_producer | Caribou 1.5 | 1025 | RD50-MPW4 | 800 MeV | Low Flux Low | Proton | Unknown | 20.09.2025 19:02:51 | 20.09.2025 19:07:54 | 5 | Normal | | | automatic log for run 1025
Comment:
bias voltage scan |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -90
[Producer.tracker_irgendwas]
|
|
218
|
Sat Sep 20 19:01:35 2025 |
elog_producer | Caribou 1.5 | 1024 | RD50-MPW4 | 800 MeV | Low Flux Low | Proton | Unknown | 20.09.2025 18:56:44 | 20.09.2025 19:01:47 | 5 | Normal | | | automatic log for run 1024
Comment:
bias voltage scan |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -80
[Producer.tracker_irgendwas]
|
|
217
|
Sat Sep 20 18:55:26 2025 |
elog_producer | Caribou 1.5 | 1023 | RD50-MPW4 | 800 MeV | Low Flux Low | Proton | Unknown | 20.09.2025 18:50:06 | 20.09.2025 18:55:38 | 5 | Normal | | | automatic log for run 1023
Comment:
bias voltage scan |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -70
[Producer.tracker_irgendwas]
|
|
216
|
Sat Sep 20 18:48:56 2025 |
elog_producer | Caribou 1.5 | 1022 | RD50-MPW4 | 800 MeV | Low Flux Low | Proton | Unknown | 20.09.2025 18:43:56 | 20.09.2025 18:49:08 | 5 | Normal | | | automatic log for run 1022
Comment:
bias voltage scan |
| Attachment 1: peary_config.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW4]
this_config_file = config.cfg
#SEC::MISC
calib_file = calib.txt
config_si5345 = clock_config_mpw4.txt
en_freeze = 1
en_tb_mode = 1
execute_file = execute.txt
i2c_addr = 0x41
i2c_dev = /dev/i2c-17
inj_t0 = 0
matrix_config = matrix_mpw4_base.txt
use_dma = 0
#SEC::REGISTERS
conf_reg_ts_ctrl = 4
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
fei3_pulldn = 0
fei3_read = 2
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vddp__u = 1.8
p1v8_vddp__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 0.93
th__u = 1
th__i = 3
|
| Attachment 2: matrix_mpw4_base.txt
|
0 0 0 0 0 0 15
0 1 0 0 0 0 3
0 2 0 0 0 0 12
0 3 0 0 0 0 13
0 4 0 0 0 0 8
0 5 0 0 0 0 11
0 6 0 0 0 0 10
0 7 0 0 0 0 8
0 8 0 0 0 0 6
0 9 0 0 0 0 10
0 10 0 0 0 0 10
0 11 0 0 0 0 4
0 12 0 0 0 0 14
0 13 0 0 0 0 7
0 14 0 0 0 0 7
0 15 0 0 0 0 2
0 16 0 0 0 0 5
0 17 0 0 0 0 15
0 18 0 0 0 0 14
0 19 0 0 0 0 12
0 20 0 0 0 0 6
0 21 0 0 0 0 5
0 22 0 0 0 0 8
0 23 0 0 0 0 7
0 24 0 0 0 0 10
0 25 0 0 0 0 4
0 26 0 0 0 0 5
0 27 0 0 0 0 0
0 28 0 0 0 0 6
0 29 0 0 0 0 5
0 30 0 0 0 0 12
0 31 0 0 0 0 2
0 32 0 0 0 0 6
0 33 0 0 0 0 8
0 34 0 0 0 0 10
0 35 0 0 0 0 9
0 36 0 0 0 0 11
0 37 0 0 0 0 8
0 38 0 0 0 0 12
0 39 0 0 0 0 8
0 40 0 0 0 0 15
0 41 0 0 0 0 7
0 42 0 0 0 0 8
0 43 0 0 0 0 5
0 44 0 0 0 0 9
0 45 0 0 0 0 14
0 46 0 0 0 0 3
0 47 0 0 0 0 7
0 48 0 0 0 0 7
0 49 0 0 0 0 7
0 50 0 0 0 0 4
0 51 0 0 0 0 8
0 52 0 0 0 0 13
0 53 0 0 0 0 7
0 54 0 0 0 0 8
0 55 0 0 0 0 10
0 56 0 0 0 0 11
0 57 0 0 0 0 5
0 58 0 0 0 0 11
0 59 0 0 0 0 3
0 60 0 0 0 0 8
0 61 0 0 0 0 4
0 62 1 0 0 0 10
0 63 0 0 0 0 10
1 0 0 0 0 0 15
1 1 0 0 0 0 10
1 2 0 0 0 0 8
1 3 0 0 0 0 7
1 4 0 0 0 0 10
1 5 0 0 0 0 0
1 6 0 0 0 0 10
1 7 0 0 0 0 15
1 8 0 0 0 0 5
1 9 0 0 0 0 15
1 10 0 0 0 0 8
1 11 0 0 0 0 3
1 12 0 0 0 0 11
1 13 0 0 0 0 10
1 14 0 0 0 0 7
1 15 0 0 0 0 2
1 16 0 0 0 0 6
1 17 0 0 0 0 13
1 18 0 0 0 0 6
1 19 0 0 0 0 11
1 20 0 0 0 0 8
1 21 0 0 0 0 14
1 22 0 0 0 0 6
1 23 0 0 0 0 14
1 24 0 0 0 0 4
1 25 0 0 0 0 9
1 26 0 0 0 0 8
1 27 0 0 0 0 8
1 28 0 0 0 0 4
1 29 0 0 0 0 3
1 30 0 0 0 0 8
1 31 0 0 0 0 6
1 32 0 0 0 0 11
1 33 0 0 0 0 4
1 34 1 0 0 0 15
1 35 0 0 0 0 9
1 36 0 0 0 0 4
1 37 0 0 0 0 7
1 38 0 0 0 0 13
1 39 0 0 0 0 8
1 40 0 0 0 0 8
1 41 0 0 0 0 5
1 42 0 0 0 0 11
1 43 0 0 0 0 5
1 44 0 0 0 0 6
1 45 0 0 0 0 14
1 46 0 0 0 0 10
1 47 0 0 0 0 6
1 48 0 0 0 0 3
1 49 0 0 0 0 9
1 50 0 0 0 0 10
1 51 0 0 0 0 7
1 52 0 0 0 0 10
1 53 0 0 0 0 10
1 54 0 0 0 0 10
1 55 0 0 0 0 4
1 56 0 0 0 0 13
1 57 0 0 0 0 11
1 58 0 0 0 0 4
1 59 0 0 0 0 5
1 60 0 0 0 0 9
1 61 0 0 0 0 8
1 62 0 0 0 0 7
1 63 0 0 0 0 11
2 0 0 0 0 0 5
2 1 0 0 0 0 10
2 2 0 0 0 0 15
2 3 0 0 0 0 7
2 4 0 0 0 0 12
2 5 0 0 0 0 15
2 6 0 0 0 0 12
2 7 0 0 0 0 14
2 8 0 0 0 0 8
2 9 0 0 0 0 12
2 10 0 0 0 0 6
2 11 0 0 0 0 7
2 12 0 0 0 0 9
2 13 0 0 0 0 5
2 14 0 0 0 0 9
2 15 0 0 0 0 5
2 16 0 0 0 0 11
2 17 0 0 0 0 9
2 18 0 0 0 0 10
2 19 0 0 0 0 9
2 20 0 0 0 0 9
2 21 0 0 0 0 6
2 22 0 0 0 0 4
2 23 0 0 0 0 7
2 24 0 0 0 0 11
2 25 0 0 0 0 1
2 26 0 0 0 0 2
2 27 0 0 0 0 9
2 28 0 0 0 0 7
2 29 0 0 0 0 8
2 30 0 0 0 0 10
2 31 0 0 0 0 12
2 32 0 0 0 0 6
2 33 0 0 0 0 8
2 34 0 0 0 0 6
2 35 0 0 0 0 11
2 36 0 0 0 0 10
2 37 0 0 0 0 14
2 38 0 0 0 0 6
2 39 0 0 0 0 6
2 40 0 0 0 0 6
2 41 0 0 0 0 9
2 42 0 0 0 0 7
2 43 0 0 0 0 11
2 44 0 0 0 0 5
2 45 0 0 0 0 10
2 46 0 0 0 0 14
2 47 0 0 0 0 7
2 48 0 0 0 0 5
2 49 0 0 0 0 12
2 50 0 0 0 0 4
2 51 0 0 0 0 8
2 52 0 0 0 0 6
2 53 0 0 0 0 5
2 54 0 0 0 0 6
2 55 0 0 0 0 8
2 56 0 0 0 0 3
2 57 0 0 0 0 6
2 58 0 0 0 0 15
2 59 0 0 0 0 15
2 60 0 0 0 0 9
2 61 0 0 0 0 11
2 62 0 0 0 0 12
2 63 0 0 0 0 9
3 0 0 0 0 0 8
3 1 0 0 0 0 12
3 2 0 0 0 0 5
3 3 0 0 0 0 1
3 4 0 0 0 0 8
3 5 0 0 0 0 9
3 6 0 0 0 0 5
3 7 0 0 0 0 7
3 8 0 0 0 0 7
3 9 0 0 0 0 9
3 10 0 0 0 0 5
3 11 0 0 0 0 5
3 12 0 0 0 0 12
3 13 0 0 0 0 2
3 14 0 0 0 0 9
3 15 0 0 0 0 0
3 16 0 0 0 0 6
3 17 0 0 0 0 14
3 18 0 0 0 0 15
3 19 0 0 0 0 9
3 20 0 0 0 0 8
3 21 0 0 0 0 6
3 22 0 0 0 0 7
3 23 0 0 0 0 8
3 24 0 0 0 0 4
3 25 0 0 0 0 3
3 26 0 0 0 0 5
3 27 0 0 0 0 4
3 28 0 0 0 0 10
3 29 0 0 0 0 8
3 30 0 0 0 0 7
3 31 0 0 0 0 12
3 32 0 0 0 0 5
3 33 0 0 0 0 4
3 34 0 0 0 0 9
3 35 0 0 0 0 5
3 36 0 0 0 0 11
3 37 0 0 0 0 11
3 38 0 0 0 0 11
3 39 0 0 0 0 11
3 40 0 0 0 0 2
3 41 0 0 0 0 7
3 42 0 0 0 0 12
3 43 0 0 0 0 12
3 44 0 0 0 0 8
3 45 0 0 0 0 12
3 46 0 0 0 0 10
3 47 0 0 0 0 3
3 48 0 0 0 0 8
3 49 0 0 0 0 8
3 50 0 0 0 0 0
3 51 0 0 0 0 8
3 52 0 0 0 0 8
3 53 0 0 0 0 10
3 54 0 0 0 0 4
3 55 0 0 0 0 3
3 56 0 0 0 0 12
3 57 0 0 0 0 3
3 58 0 0 0 0 5
3 59 0 0 0 0 8
3 60 0 0 0 0 9
3 61 0 0 0 0 5
3 62 0 0 0 0 8
3 63 0 0 0 0 1
4 0 0 0 0 0 8
4 1 0 0 0 0 15
4 2 0 0 0 0 12
4 3 0 0 0 0 4
4 4 0 0 0 0 9
4 5 0 0 0 0 11
4 6 0 0 0 0 14
4 7 0 0 0 0 11
4 8 0 0 0 0 4
4 9 0 0 0 0 7
4 10 0 0 0 0 8
4 11 0 0 0 0 12
4 12 0 0 0 0 10
4 13 0 0 0 0 11
4 14 0 0 0 0 7
4 15 0 0 0 0 11
4 16 0 0 0 0 4
4 17 0 0 0 0 10
4 18 0 0 0 0 10
4 19 0 0 0 0 14
4 20 0 0 0 0 11
4 21 0 0 0 0 11
4 22 0 0 0 0 8
4 23 0 0 0 0 11
4 24 0 0 0 0 1
4 25 0 0 0 0 2
4 26 0 0 0 0 9
4 27 0 0 0 0 11
4 28 0 0 0 0 8
4 29 0 0 0 0 3
4 30 0 0 0 0 5
4 31 0 0 0 0 8
4 32 0 0 0 0 4
4 33 0 0 0 0 9
4 34 0 0 0 0 8
4 35 0 0 0 0 3
4 36 0 0 0 0 3
4 37 0 0 0 0 11
4 38 0 0 0 0 7
4 39 0 0 0 0 10
4 40 0 0 0 0 12
4 41 0 0 0 0 7
4 42 0 0 0 0 6
4 43 0 0 0 0 4
... 3796 more lines ...
|
| Attachment 3: mpw4.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xF0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xD #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/tlu/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW4_0]
#register_key = "vnfb"
#register_value = 0x12
EUDAQ_DC= peary_dc
[DataCollector.mpw4_dc]
# connection to the monitor
EUDAQ_MN = mpw4_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/Elements/caribou_maus_250920/mpw4/mpw4_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[DataCollector.peary_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/Elements/caribou_maus_250920/peary/peary_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Monitor.mpw4_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[Producer.elog1]
start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
files2log = "peary_config.cfg, matrix_mpw4_base.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
[Producer.keithleyPS]
max_current = 50e-6
ramp_speed = 100
ramp_step = 2.5
voltage = -60
[Producer.tracker_irgendwas]
|
|