| ID |
Date |
Author |
Subject |
Run Number |
DUT |
Beam Energy |
Rate Setting |
Particle Type |
Data |
t-Start |
t-Stop |
Duration_min |
Frontend |
Phantom |
Phantom thickness |
|
74
|
Sat Mar 15 21:29:28 2025 |
RD50 Generic User | Slab and rate testing (with Michael) | 13 | Sandwich-iCT setup(GSI)+RaMon | 205.2 MeV/u | Low Flux High | Helium | Good | 20:44 | 21:22 | 38 | | Plastic Water Slabs | 4cm | totzeit optimieren und deadtime finden
hex wert mal 10ns deadtime
13 ab file 10 besat effort
ab 52 wieder ohne best effort
600 |
|
87
|
Sat Jun 21 20:15:25 2025 |
Julia Müllner | 177.8 MeV systemtest | 13 | TOF-Cal GSI | 177.8 MeV/u | Low Flux High | Helium | Good | 20:16 | 20:23 | 7 | | | | 16.2 GB collected |
|
259
|
Sat Dec 6 18:36:14 2025 |
Felix Ulrich-Pur | 800MeV systemtest | 13 | TOF-Cal GSI (TRB)+DOGMA setup(diamond+LGAD)+RaMon | 800 MeV | Low Flux Very Low | Proton | Good | 18:53 | 19:18 | 25 | | None | | Run nr. 12 wasn't recorded.
new calib from this run on |
|
344
|
Sat Dec 13 13:23:37 2025 |
elog_producer | energy calibration | 13 | Sandwich-iCT setup(GSI)+RaMon | 147.2 MeV/u | Low Flux High | Helium | Good | 13.12.2025 13:16:13 | 13.12.2025 13:24:02 | 7 | Normal | None | | automatic log for run 13
Comment:
alignment run 147.2 MeV |
| Attachment 1: ramon.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.8
PMT4_V= 0.8
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 # 0x00000008 Koinzidenz 1+2 ; 0x00000040 Koinzidenz 2+3
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
#DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="LU_MedAustron"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.elog1]
|
|
72
|
Sat Mar 15 19:37:42 2025 |
RD50 Generic User | Slab Test Water 4cm | 12 | Sandwich-iCT setup(GSI)+RaMon | 205.2 MeV/u | Low Flux Medium | Helium | | 19:39 | 20:41 | 62 | | Plastic Water Slabs | 4cm | RaMon Rate 1.4MHz |
|
86
|
Sat Jun 21 20:05:49 2025 |
Julia Müllner | 147.2 MeV systemtest | 12 | TOF-Cal GSI | 147.2 MeV/u | Low Flux High | Helium | Good | 20:06 | 20:15 | 9 | | | | |
|
343
|
Sat Dec 13 13:13:59 2025 |
elog_producer | energy calibration | 12 | Sandwich-iCT setup(GSI)+RaMon | 177.8 MeV/u | Low Flux High | Helium | Good | 13.12.2025 13:02:49 | 13.12.2025 13:14:24 | 11 | Normal | None | | automatic log for run 12
Comment:
alignment run 177.8 MeV |
| Attachment 1: ramon.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.8
PMT4_V= 0.8
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 # 0x00000008 Koinzidenz 1+2 ; 0x00000040 Koinzidenz 2+3
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
#DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="LU_MedAustron"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.elog1]
|
|
12
|
Fri Mar 14 21:44:46 2025 |
elog-producer | validating setup | 118 | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | 14.03.2025 21:44:20 | 14.03.2025 21:45:12 | 0 | HV | None | | automatic log for run 118
Comment:
tracker test without beam |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 6 # 0
in0_DEL = 0 # 18
in1_STR = 6 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 50000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xB
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x3F #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xB #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN="/home/silicon/TJ-Monopix2/testbeam_03_2025/tlu/tlu_run$6R.raw"
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_W02R01]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W02R01_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.10.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W02R01"
chip_sn="W02R01"
online_monitor_port="5500"
[Producer.tjmonopix2_W14R18]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W14R18_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.12.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W14R18"
chip_sn="W14R18"
online_monitor_port="5700"
[Producer.HamegProducer]
hv=20
power_cycle_at_stop=1 #0=False 1=True
logging=1 #0=False 1=True
log_interval=10
logging_directory="/home/silicon/TJ-Monopix2/TJ-Monopix2-Power/Log/testbeam_prep"
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
11
|
Fri Mar 14 21:43:10 2025 |
elog-producer | validating setup | 117 | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | 14.03.2025 21:42:46 | 14.03.2025 21:43:36 | 0 | HV | None | | automatic log for run 117
Comment:
tracker test without beam |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 6 # 0
in0_DEL = 0 # 18
in1_STR = 6 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 50000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xB
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x3F #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xB #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN="/home/silicon/TJ-Monopix2/testbeam_03_2025/tlu/tlu_run$6R.raw"
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_W02R01]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W02R01_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.10.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W02R01"
chip_sn="W02R01"
online_monitor_port="5500"
[Producer.tjmonopix2_W14R18]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W14R18_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.12.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W14R18"
chip_sn="W14R18"
online_monitor_port="5700"
[Producer.HamegProducer]
hv=20
power_cycle_at_stop=1 #0=False 1=True
logging=1 #0=False 1=True
log_interval=10
logging_directory="/home/silicon/TJ-Monopix2/TJ-Monopix2-Power/Log/testbeam_prep"
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
10
|
Fri Mar 14 21:41:12 2025 |
elog-producer | validating setup | 116 | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | 14.03.2025 21:41:05 | 14.03.2025 21:41:38 | 0 | HV | None | | automatic log for run 116
Comment:
tracker test without beam |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 6 # 0
in0_DEL = 0 # 18
in1_STR = 6 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 20000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xB
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x3F #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xB #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN="/home/silicon/TJ-Monopix2/testbeam_03_2025/tlu/tlu_run$6R.raw"
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_W02R01]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W02R01_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.10.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W02R01"
chip_sn="W02R01"
online_monitor_port="5500"
[Producer.tjmonopix2_W14R18]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W14R18_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.12.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W14R18"
chip_sn="W14R18"
online_monitor_port="5700"
[Producer.HamegProducer]
hv=20
power_cycle_at_stop=1 #0=False 1=True
logging=1 #0=False 1=True
log_interval=10
logging_directory="/home/silicon/TJ-Monopix2/TJ-Monopix2-Power/Log/testbeam_prep"
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
8
|
Fri Mar 14 20:40:06 2025 |
elog-producer | validating setup | 112 | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | 14.03.2025 20:07:47 | 14.03.2025 20:40:32 | 32 | HV | None | | automatic log for run 112
Comment:
still testing nonsense |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 6 # 0
in0_DEL = 0 # 18
in1_STR = 6 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 10 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x3F #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN="/home/silicon/TJ-Monopix2/testbeam_03_2025/tlu/tlu_run$6R.raw"
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_W02R01]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W02R01_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.10.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W02R01"
chip_sn="W02R01"
online_monitor_port="5500"
[Producer.tjmonopix2_W14R18]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W14R18_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.12.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W14R18"
chip_sn="W14R18"
online_monitor_port="5700"
[Producer.HamegProducer]
hv=20
power_cycle_at_stop=1 #0=False 1=True
logging=1 #0=False 1=True
log_interval=10
logging_directory="/home/silicon/TJ-Monopix2/TJ-Monopix2-Power/Log/testbeam_prep"
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
7
|
Fri Mar 14 20:04:41 2025 |
elog-producer | validating setup | 111 | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | 14.03.2025 20:03:34 | 14.03.2025 20:05:07 | 1 | HV | None | | automatic log for run 111
Comment:
bla |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 6 # 0
in0_DEL = 0 # 18
in1_STR = 6 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 10 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x3F #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN="/home/silicon/TJ-Monopix2/testbeam_03_2025/tlu/tlu_run$6R.raw"
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_W02R01]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W02R01_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.10.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W02R01"
chip_sn="W02R01"
online_monitor_port="5500"
[Producer.tjmonopix2_W14R18]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W14R18_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.12.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W14R18"
chip_sn="W14R18"
online_monitor_port="5700"
[Producer.HamegProducer]
hv=20
power_cycle_at_stop=1 #0=False 1=True
logging=1 #0=False 1=True
log_interval=10
logging_directory="/home/silicon/TJ-Monopix2/TJ-Monopix2-Power/Log/testbeam_prep"
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
6
|
Fri Mar 14 19:57:28 2025 |
elog-producer | validating setup | 110 | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | 14.03.2025 19:51:51 | 14.03.2025 19:57:54 | 6 | HV | None | | automatic log for run 110
Comment:
bla |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 6 # 0
in0_DEL = 0 # 18
in1_STR = 6 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 10 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x3F #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN="/home/silicon/TJ-Monopix2/testbeam_03_2025/tlu/tlu_run$6R.raw"
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_W02R01]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W02R01_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.10.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W02R01"
chip_sn="W02R01"
online_monitor_port="5500"
[Producer.tjmonopix2_W14R18]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W14R18_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.12.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W14R18"
chip_sn="W14R18"
online_monitor_port="5700"
[Producer.HamegProducer]
hv=20
power_cycle_at_stop=1 #0=False 1=True
logging=1 #0=False 1=True
log_interval=10
logging_directory="/home/silicon/TJ-Monopix2/TJ-Monopix2-Power/Log/testbeam_prep"
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
71
|
Sat Mar 15 18:37:36 2025 |
RD50 Generic User | Slab Test Water 3cm | 11 | Sandwich-iCT setup(GSI)+RaMon | 205.2 MeV/u | Low Flux Medium | Helium | | 18:41 | 19:28 | 47 | | Plastic Water Slabs | 3cm | RaMon Rate 1.5MHz |
|
85
|
Sat Jun 21 19:54:12 2025 |
Julia Müllner | 124.4 MeV systemtest | 11 | TOF-Cal GSI | 124.4 MeV/u | Low Flux High | Helium | Good | 19:54 | 20:05 | 11 | | | | 16GB collected |
|
258
|
Sat Dec 6 18:08:39 2025 |
Felix Ulrich-Pur | 800MeV systemtest | 11 | TOF-Cal GSI (TRB)+DOGMA setup(diamond+LGAD)+RaMon | 800 MeV | Low Flux High | Proton | Good | 18:16 | 18:23 | 7 | | None | | adjusted threshold for double-sided LGAD (accounted for polarity of signal) |
|
342
|
Sat Dec 13 13:00:26 2025 |
elog_producer | energy calibration | 11 | Sandwich-iCT setup(GSI)+RaMon | 205.2 MeV/u | Low Flux High | Helium | Good | 13.12.2025 12:52:23 | 13.12.2025 13:00:52 | 8 | Normal | None | | automatic log for run 11
Comment:
alignment run 205.2 MeV |
| Attachment 1: ramon.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.8
PMT4_V= 0.8
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 # 0x00000008 Koinzidenz 1+2 ; 0x00000040 Koinzidenz 2+3
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
#DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="LU_MedAustron"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.elog1]
|
|
5
|
Fri Mar 14 19:50:29 2025 |
elog-producer | validating setup | 109 | TJ-Monopix2 | 800 MeV | Low Flux Very Low | Proton | Unknown | 14.03.2025 19:49:10 | 14.03.2025 19:50:55 | 1 | HV | None | | automatic log for run 109
Comment:
system tests |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 6 # 0
in0_DEL = 0 # 18
in1_STR = 6 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 10 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x3F #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN="/home/silicon/TJ-Monopix2/testbeam_03_2025/tlu/tlu_run$6R.raw"
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.tjmonopix2_W02R01]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W02R01_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.10.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W02R01"
chip_sn="W02R01"
online_monitor_port="5500"
[Producer.tjmonopix2_W14R18]
start_column=448
stop_column=512
start_row=0
stop_row=512
scan_timeout=0
max_triggers=0
chip_config_file="/home/silicon/TJ-Monopix2/Tuning/2BDAQ_boards_test/HV_W14R18_threshold_scan_interpreted.h5"
VCLIP=255
daqboard_ip="192.168.12.23"
output_directory="/home/silicon/TJ-Monopix2/testbeam_03_2025/W14R18"
chip_sn="W14R18"
online_monitor_port="5700"
[Producer.HamegProducer]
hv=20
power_cycle_at_stop=1 #0=False 1=True
logging=1 #0=False 1=True
log_interval=10
logging_directory="/home/silicon/TJ-Monopix2/TJ-Monopix2-Power/Log/testbeam_prep"
[Producer.elog1]
#start_cmd = "./get_mpw4_configs.sh" # command (shell script) to execute before starting a run
#files2log = "peary_config.cfg, matrix_mpw4.txt" #files to attach to the auto Elog entries, EUDAQ config will be logged by default
|
|
196
|
Sat Aug 16 21:08:36 2025 |
elog_producer | Castid | 108 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Unknown | 16.08.2025 20:59:05 | 16.08.2025 21:08:39 | 9 | HV | None | | automatic log for run 108
Comment:
self.configure_rx(delay=2, rd_frz_dly=2) (20x) |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #Szinti 4x4cm
PMT2_V= 0.8 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
#InternalTriggerFreq= 5 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.012 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xFF #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|
195
|
Sat Aug 16 20:58:19 2025 |
elog_producer | Castid | 107 | TJ-Monopix2 | 800 MeV | Low Flux Medium | Proton | Unknown | 16.08.2025 20:47:55 | 16.08.2025 20:58:21 | 10 | HV | None | | automatic log for run 107
Comment:
self.configure_rx(delay=2, rd_frz_dly=2) (20x) |
| Attachment 1: tjmonopix2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #Szinti 4x4cm
PMT2_V= 0.8 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
#InternalTriggerFreq= 5 #1000 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.012 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 # bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xFF #0x00 # Full Monopix on all 4 DUTs
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="tjmonopix2"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/castid-TB_MAUS_Aug25/data/TLU/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.W02R01]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W02R01/20240222_174415_threshold_scan_interpreted.h5
chip_sn = W02R01
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W02R01
online_monitor_port="5500"
daqboard_ip = "192.168.10.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W08R19]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W08R19/20230708_095321_threshold_scan_interpreted.h5
chip_sn = W08R19
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W08R19
online_monitor_port="5510"
daqboard_ip = "192.168.11.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W14R12]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W14R12/20250804_172438_threshold_scan_interpreted.h5
chip_sn = W14R12
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W14R12
online_monitor_port="5520"
daqboard_ip = "192.168.12.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
[Producer.W18R03]
# connection to the data collector
chip_config_file = /home/silicon/castid-TB_MAUS_Aug25/config/tuning/W18R03/20240222_183330_threshold_scan_interpreted.h5
chip_sn = W18R03
output_directory = /home/silicon/castid-TB_MAUS_Aug25/data/W18R03
online_monitor_port="5530"
daqboard_ip = "192.168.13.23"
start_column=448
stop_column=512
start_row=0
stop_row=512
#[DataCollector.dc_monopix2]
#EUDAQ_MN = monopix2_mon
#EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 1000
#EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/TJ-Monopix2/test-data/raw/mpx2_run$3R_$12D$X
##EUDAQ_FW_PATTERN = /home/mx/Schule/Nosync/EUDAQ/test_corry/raw/mpx2_run$3R_$12D$X
#DISABLE_PRINT = 1
|
|