| ID |
Date |
Author |
Subject |
Run Number |
DUT |
Beam Energy |
Rate Setting |
Particle Type |
Data |
t-Start |
t-Stop |
Duration_min |
Frontend |
Phantom |
Phantom thickness |
|
259
|
Sat Dec 6 18:36:14 2025 |
Felix Ulrich-Pur | 800MeV systemtest | 13 | TOF-Cal GSI (TRB)+DOGMA setup(diamond+LGAD)+RaMon | 800 MeV | Low Flux Very Low | Proton | Good | 18:53 | 19:18 | 25 | | None | |
Run nr. 12 wasn't recorded.
new calib from this run on |
|
260
|
Sat Dec 6 19:20:24 2025 |
Felix Ulrich-Pur | 800MeV systemtest | 14 | TOF-Cal GSI (TRB)+DOGMA setup(diamond+LGAD)+RaMon | 800 MeV | Low Flux High | Proton | Good | 19:30 | 19:45 | 15 | | None | |
3360ns PreTriggerWindow and 640ns PostTriggerWindow
Had to restart eventbuilder at 19:39 due to high rejected rate
60Mb/s Events and 10-15Mb/s rejected |
|
261
|
Sat Dec 6 19:47:32 2025 |
Felix Ulrich-Pur | 800MeV systemtest | 15 | TOF-Cal GSI (TRB)+DOGMA setup(diamond+LGAD)+RaMon | 800 MeV | Low Flux High | Proton | Good | 19:48 | 19:57 | 9 | | None | |
PreTriggerWindow: 640ns and PostTriggerWindow: 3.36µs
25Mb/s Events and 25Mb/s rejected |
|
262
|
Sat Dec 6 19:59:15 2025 |
Felix Ulrich-Pur | 800MeV systemtest | 16 | TOF-Cal GSI (TRB)+DOGMA setup(diamond+LGAD)+RaMon | 800 MeV | Low Flux High | Helium | Good | 19:59 | 20:09 | 10 | | None | |
40Mb/s Events and 4 Mb/s rejected
PreTriggerWindow: 1360ns and PostTriggerWindow: 640ns |
|
82
|
Sat Jun 21 18:22:28 2025 |
Julia Müllner | 73.2 MeV systemtest | 8 | TOF-Cal GSI | 73.2 MeV/u | Low Flux High | Helium | Crap | 19:10 | 19:21 | 11 | | | |
new callibration was done, dimanond detector connected to readout
Threshold = 4000
thresholds were too low -> run was canceled |
|
83
|
Sat Jun 21 19:22:45 2025 |
Julia Müllner | 73.2 MeV systemtest | 9 | TOF-Cal GSI | 73.2 MeV/u | Low Flux High | Helium | Good | 19:23 | 19:35 | 12 | | | |
Threshold change from 50 to 500
10GB collected |
|
273
|
Sat Dec 6 23:50:07 2025 |
Felix Ulrich-Pur | 73.2 MeV/u systemtest | 27 | TOF-Cal GSI (TRB)+DOGMA setup(diamond+LGAD)+RaMon | 73.2 MeV/u | Low Flux High | Helium | Good | 23:50 | 0:08 | 18 | | None | |
20 Mb/s Events and max 50 kB/s rejected
PreTriggerWindow 640ns and PostTriggerWindow 85ns |
|
347
|
Sat Dec 13 14:00:52 2025 |
elog_producer | energy calibration | 16 | Sandwich-iCT setup(GSI)+RaMon | 73.2 MeV/u | Low Flux High | Helium | Good | 13.12.2025 13:47:23 | 13.12.2025 14:01:18 | 13 | Normal | None | |
automatic log for run 16
Comment:
calibration run 73.2 MeV |
| Attachment 1: ramon.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.8
PMT4_V= 0.8
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 # 0x00000008 Koinzidenz 1+2 ; 0x00000040 Koinzidenz 2+3
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
#DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="LU_MedAustron"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.elog1]
|
|
84
|
Sat Jun 21 19:35:59 2025 |
Julia Müllner | 63.3 MeV systemtest | 10 | TOF-Cal GSI | 63.3 MeV/u | Low Flux High | Helium | Good | 19:37 | 19:53 | 16 | | | |
|
|
274
|
Sun Dec 7 00:08:52 2025 |
Felix Ulrich-Pur | 63.3 MeV/u systemtest | 28 | TOF-Cal GSI (TRB)+DOGMA setup(diamond+LGAD)+RaMon | 63.3 MeV/u | Low Flux High | Helium | Good | 0:09 | 00:37 | 28 | | None | |
15 Mb/s Events and 30kb/s rejected
PreTriggerWindow 640ns and PostTriggerWindow 85ns |
|
348
|
Sat Dec 13 14:18:49 2025 |
elog_producer | energy calibration | 17 | Sandwich-iCT setup(GSI)+RaMon | 63.3 MeV/u | Low Flux High | Helium | Good | 13.12.2025 14:02:30 | 13.12.2025 14:19:14 | 16 | Normal | None | |
automatic log for run 17
Comment:
calibration run 63.3 MeV |
| Attachment 1: ramon.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.8 #0.6363 #Szinti 4x4cm
PMT2_V= 0.8 #0.6363 #Szinti 4x4cm
PMT3_V= 0.8
PMT4_V= 0.8
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 # 0x00000008 Koinzidenz 1+2 ; 0x00000040 Koinzidenz 2+3
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.025 #-0.025 #-0.012
DACThreshold2 = -0.012
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
#DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="LU_MedAustron"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.elog1]
|
|
89
|
Sat Jun 21 20:32:58 2025 |
Julia Müllner | 402MeV systemtest | 15 | TOF-Cal GSI | 402MeV/u | Low Flux High | Helium | Good | 20:35 | 20:47 | 12 | | | |
rejected roughly 10-20%, 8MHz beam
rejected quite a lot of data later -> eventloader restarted |
|
132
|
Sun Jun 22 05:16:32 2025 |
Julia Müllner | 402 MeV mouse | 58 | TOF-Cal GSI | 402MeV/u | Low Flux High | Carbon | Good | 5:29 | 6:00 | 31 | | | |
axis 1: 5
axis 2: 2
degrader 10, mouse is still inside |
|
249
|
Sat Dec 6 16:14:11 2025 |
Felix Ulrich-Pur | 402MeV/u systemtest | 2 | TOF-Cal GSI (TRB)+DOGMA setup(diamond+LGAD)+RaMon | 402MeV/u | Low Flux High | Helium | Unknown | 15:55 | 16:00 | 5 | | None | |
|
|
250
|
Sat Dec 6 16:15:17 2025 |
Felix Ulrich-Pur | 402MeV/u systemtest | 3 | TOF-Cal GSI (TRB)+DOGMA setup(diamond+LGAD)+RaMon | 402MeV/u | Low Flux High | Helium | Unknown | 16:05 | 16:23 | 18 | | None | |
|
|
251
|
Sat Dec 6 16:25:24 2025 |
Felix Ulrich-Pur | 402MeV/u systemtest | 4 | TOF-Cal GSI (TRB)+DOGMA setup(diamond+LGAD)+RaMon | 402MeV/u | Low Flux High | Helium | Good | 16:23 | 16:24 | 1 | | None | |
just to check if the beam was there |
|
252
|
Sat Dec 6 16:27:41 2025 |
Felix Ulrich-Pur | 402MeV/u systemtest | 5 | TOF-Cal GSI (TRB)+DOGMA setup(diamond+LGAD)+RaMon | 402MeV/u | Low Flux High | Helium | Good | 16:27 | 16:34 | 7 | | None | |
interupted to get inside the room |
|
253
|
Sat Dec 6 16:41:57 2025 |
Felix Ulrich-Pur | 402MeV/u systemtest | 6 | TOF-Cal GSI (TRB)+DOGMA setup(diamond+LGAD)+RaMon | 402MeV/u | Low Flux High | Helium | Good | 16:42 | 16:47 | 5 | | None | |
setup was moved, stopped to move setup again
threshold = 4000 |
|
254
|
Sat Dec 6 16:53:28 2025 |
Felix Ulrich-Pur | 402MeV/u systemtest | 7 | TOF-Cal GSI (TRB)+DOGMA setup(diamond+LGAD)+RaMon | 402MeV/u | Low Flux High | Helium | Good | 16:53 | 17:08 | 15 | | None | |
Setup wurde verschoben: 5mm vorne nach links und hinten 4mm, in Beamrichtung
threshold = 4000 |
|
255
|
Sat Dec 6 17:12:41 2025 |
Felix Ulrich-Pur | 402MeV/u systemtest | 8 | TOF-Cal GSI (TRB)+DOGMA setup(diamond+LGAD)+RaMon | 402MeV/u | Low Flux High | Helium | Good | 17:15 | 17:22 | 7 | | None | |
threshold = 2000
PreTriggerWindow 640ns und PostTriggerWindow 85ns |