| ID |
Date |
Author |
Subject |
Run Number |
DUT |
Beam Energy |
Rate Setting |
Particle Type |
Events |
Data |
t-Start |
t-Stop |
Duration_min |
Frontend |
|
180
|
Sat Oct 14 22:32:07 2023 |
tb crew | RD50-MPW3 | 17 | RD50-MPW3 | 800 | Low Flux Low | Proton | | Unknown | 14.10.2023 22:26:10 | 14.10.2023 22:32:31 | 6 | Normal | automatic log for run 17
Comment: |
| Attachment 1: peary.cfg
|
#This config file was generated with the "MPW3_gui - Config Creator"
#Do not change comment lines like "SEC::xxx" !
#They are needed for parsing
[RD50_MPW3]
inj_t0 = 0
this_config_file = config_piggy_new.cfg
#SEC::MISC
accept_tlu_trigger = 0
enable_readout = 1
calib_file_base = calib_base.txt
config_si5345 = clock_config.txt
execute_file = execute.txt
i2c_addr_base = 0x41
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_base.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 0
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
#SEC::POWER
# voltages with suffix "__u", currents with "__i"
bl__u = 0.9
bl__i = 3
del_hi__u = 0.7
del_hi__i = 3
del_lo__u = 0.9
del_lo__i = 3
p1v3_vssa__u = 1.3
p1v3_vssa__i = 3
p1v8_nw_ring__u = 1.8
p1v8_nw_ring__i = 3
p1v8_vdd!__u = 1.8
p1v8_vdd!__i = 3
p1v8_vdda__u = 1.8
p1v8_vdda__i = 3
p1v8_vddc__u = 1.8
p1v8_vddc__i = 3
p1v8_vsensbus__u = 1.8
p1v8_vsensbus__i = 3
p2v5d__u = 2.5
p2v5d__i = 3
th__u = 1.2
th__i = 3
[RD50_MPW3_Piggy]
this_config_file = config_piggy_new.cfg
#SEC::MISC
calib_file = calib_piggy.txt
execute_file = execute.txt
i2c_addr = 0x47
i2c_dev = /dev/i2c-9
matrix_config = matrix_config_piggy.txt
#SEC::REGISTERS
conf_reg_ts_ctrl = 0
conf_reg_ts_ini = 0
cu_ctrl = 0
en_ext_ctrl = 0
en_ser_out_dcol = 0
en_sfout_dcol = 0
idle0 = 251
idle1 = 247
idle2 = 247
idle3 = 247
tx_ctrl = 0
vbfb = 38
vblr = 38
vn = 21
vnfb = 18
vnsensbias = 50
vnsf = 45
vpbias = 37
vpcomp = 19
vptrim = 36
|
| Attachment 2: matrix_config_base.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 1 0 0 0 -1
00 01 1 0 0 0 -1
00 02 1 0 0 0 -1
00 03 1 0 0 0 -1
00 04 1 0 0 0 -1
00 05 1 0 0 0 -1
00 06 1 0 0 0 -1
00 07 1 0 0 0 -1
00 08 1 0 0 0 -1
00 09 1 0 0 0 -1
00 10 1 0 0 0 -1
00 11 1 0 0 0 -1
00 12 1 0 0 0 -1
00 13 1 0 0 0 -1
00 14 1 0 0 0 -1
00 15 1 0 0 0 -1
00 16 1 0 0 0 -1
00 17 1 0 0 0 -1
00 18 1 0 0 0 -1
00 19 1 0 0 0 -1
00 20 1 0 0 0 -1
00 21 1 0 0 0 -1
00 22 1 0 0 0 -1
00 23 1 0 0 0 -1
00 24 1 0 0 0 -1
00 25 1 0 0 0 -1
00 26 1 0 0 0 -1
00 27 1 0 0 0 -1
00 28 1 0 0 0 -1
00 29 1 0 0 0 -1
00 30 1 0 0 0 -1
00 31 1 0 0 0 -1
00 32 1 0 0 0 -1
00 33 1 0 0 0 -1
00 34 1 0 0 0 -1
00 35 1 0 0 0 -1
00 36 1 0 0 0 -1
00 37 1 0 0 0 -1
00 38 1 0 0 0 -1
00 39 1 0 0 0 -1
00 40 1 0 0 0 -1
00 41 1 0 0 0 -1
00 42 1 0 0 0 -1
00 43 1 0 0 0 -1
00 44 1 0 0 0 -1
00 45 1 0 0 0 -1
00 46 1 0 0 0 -1
00 47 1 0 0 0 -1
00 48 1 0 0 0 -1
00 49 1 0 0 0 -1
00 50 1 0 0 0 -1
00 51 1 0 0 0 -1
00 52 1 0 0 0 -1
00 53 1 0 0 0 -1
00 54 1 0 0 0 -1
00 55 1 0 0 0 -1
00 56 1 0 0 0 -1
00 57 1 0 0 0 -1
00 58 1 0 0 0 -1
00 59 1 0 0 0 -1
00 60 1 0 0 0 -1
00 61 1 0 0 0 -1
00 62 1 0 0 0 -1
00 63 1 0 0 0 -1
01 00 1 0 0 0 -1
01 01 1 0 0 0 -1
01 02 1 0 0 0 -1
01 03 1 0 0 0 -1
01 04 1 0 0 0 -1
01 05 1 0 0 0 -1
01 06 1 0 0 0 -1
01 07 1 0 0 0 -1
01 08 1 0 0 0 -1
01 09 1 0 0 0 -1
01 10 1 0 0 0 -1
01 11 1 0 0 0 -1
01 12 1 0 0 0 -1
01 13 1 0 0 0 -1
01 14 1 0 0 0 -1
01 15 1 0 0 0 -1
01 16 1 0 0 0 -1
01 17 1 0 0 0 -1
01 18 1 0 0 0 -1
01 19 1 0 0 0 -1
01 20 1 0 0 0 -1
01 21 1 0 0 0 -1
01 22 1 0 0 0 -1
01 23 1 0 0 0 -1
01 24 1 0 0 0 -1
01 25 1 0 0 0 -1
01 26 1 0 0 0 -1
01 27 1 0 0 0 -1
01 28 1 0 0 0 -1
01 29 1 0 0 0 -1
01 30 1 0 0 0 -1
01 31 1 0 0 0 -1
01 32 1 0 0 0 -1
01 33 1 0 0 0 -1
01 34 1 0 0 0 -1
01 35 1 0 0 0 -1
01 36 1 0 0 0 -1
01 37 1 0 0 0 -1
01 38 1 0 0 0 -1
01 39 1 0 0 0 -1
01 40 1 0 0 0 -1
01 41 1 0 0 0 -1
01 42 1 0 0 0 -1
01 43 1 0 0 0 -1
01 44 1 0 0 0 -1
01 45 1 0 0 0 -1
01 46 1 0 0 0 -1
01 47 1 0 0 0 -1
01 48 1 0 0 0 -1
01 49 1 0 0 0 -1
01 50 1 0 0 0 -1
01 51 1 0 0 0 -1
01 52 1 0 0 0 -1
01 53 1 0 0 0 -1
01 54 1 0 0 0 -1
01 55 1 0 0 0 -1
01 56 1 0 0 0 -1
01 57 1 0 0 0 -1
01 58 1 0 0 0 -1
01 59 1 0 0 0 -1
01 60 1 0 0 0 -1
01 61 1 0 0 0 -1
01 62 1 0 0 0 -1
01 63 1 0 0 0 -1
02 00 1 0 0 0 -1
02 01 1 0 0 0 -1
02 02 1 0 0 0 -1
02 03 1 0 0 0 -1
02 04 1 0 0 0 -1
02 05 1 0 0 0 -1
02 06 1 0 0 0 -1
02 07 1 0 0 0 -1
02 08 1 0 0 0 -1
02 09 1 0 0 0 -1
02 10 1 0 0 0 -1
02 11 1 0 0 0 -1
02 12 1 0 0 0 -1
02 13 1 0 0 0 -1
02 14 1 0 0 0 -1
02 15 1 0 0 0 -1
02 16 1 0 0 0 -1
02 17 1 0 0 0 -1
02 18 1 0 0 0 -1
02 19 1 0 0 0 -1
02 20 1 0 0 0 -1
02 21 1 0 0 0 -1
02 22 1 0 0 0 -1
02 23 1 0 0 0 -1
02 24 1 0 0 0 -1
02 25 1 0 0 0 -1
02 26 1 0 0 0 -1
02 27 1 0 0 0 -1
02 28 1 0 0 0 -1
02 29 1 0 0 0 -1
02 30 1 0 0 0 -1
02 31 1 0 0 0 -1
02 32 1 0 0 0 -1
02 33 1 0 0 0 -1
02 34 1 0 0 0 -1
02 35 1 0 0 0 -1
02 36 1 0 0 0 -1
02 37 1 0 0 0 -1
02 38 1 0 0 0 -1
02 39 1 0 0 0 -1
02 40 1 0 0 0 -1
02 41 1 0 0 0 -1
02 42 1 0 0 0 -1
02 43 1 0 0 0 -1
02 44 1 0 0 0 -1
02 45 1 0 0 0 -1
02 46 1 0 0 0 -1
02 47 1 0 0 0 -1
02 48 1 0 0 0 -1
02 49 1 0 0 0 -1
02 50 1 0 0 0 -1
02 51 1 0 0 0 -1
02 52 1 0 0 0 -1
02 53 1 0 0 0 -1
02 54 1 0 0 0 -1
02 55 1 0 0 0 -1
02 56 1 0 0 0 -1
02 57 1 0 0 0 -1
02 58 1 0 0 0 -1
02 59 1 0 0 0 -1
02 60 1 0 0 0 -1
02 61 1 0 0 0 -1
02 62 1 0 0 0 -1
02 63 1 0 0 0 -1
03 00 1 0 0 0 -1
03 01 1 0 0 0 -1
03 02 1 0 0 0 -1
03 03 1 0 0 0 -1
03 04 1 0 0 0 -1
03 05 1 0 0 0 -1
03 06 1 0 0 0 -1
03 07 1 0 0 0 -1
03 08 1 0 0 0 -1
03 09 1 0 0 0 -1
03 10 1 0 0 0 -1
03 11 1 0 0 0 -1
03 12 1 0 0 0 -1
03 13 1 0 0 0 -1
03 14 1 0 0 0 -1
03 15 1 0 0 0 -1
03 16 1 0 0 0 -1
03 17 1 0 0 0 -1
03 18 1 0 0 0 -1
03 19 1 0 0 0 -1
03 20 1 0 0 0 -1
03 21 1 0 0 0 -1
03 22 1 0 0 0 -1
03 23 1 0 0 0 -1
03 24 1 0 0 0 -1
03 25 1 0 0 0 -1
03 26 1 0 0 0 -1
03 27 1 0 0 0 -1
03 28 1 0 0 0 -1
03 29 1 0 0 0 -1
03 30 1 0 0 0 -1
03 31 1 0 0 0 -1
03 32 1 0 0 0 -1
03 33 1 0 0 0 -1
03 34 1 0 0 0 -1
03 35 1 0 0 0 -1
03 36 1 0 0 0 -1
03 37 1 0 0 0 -1
03 38 1 0 0 0 -1
03 39 1 0 0 0 -1
03 40 1 0 0 0 -1
03 41 1 0 0 0 -1
03 42 1 0 0 0 -1
03 43 1 0 0 0 -1
03 44 1 0 0 0 -1
03 45 1 0 0 0 -1
03 46 1 0 0 0 -1
03 47 1 0 0 0 -1
03 48 1 0 0 0 -1
03 49 1 0 0 0 -1
03 50 1 0 0 0 -1
03 51 1 0 0 0 -1
03 52 1 0 0 0 -1
03 53 1 0 0 0 -1
03 54 1 0 0 0 -1
03 55 1 0 0 0 -1
03 56 1 0 0 0 -1
03 57 1 0 0 0 -1
03 58 1 0 0 0 -1
03 59 1 0 0 0 -1
03 60 1 0 0 0 -1
03 61 1 0 0 0 -1
03 62 1 0 0 0 -1
03 63 1 0 0 0 -1
04 00 1 0 0 0 -1
04 01 1 0 0 0 -1
04 02 1 0 0 0 -1
04 03 1 0 0 0 -1
04 04 1 0 0 0 -1
04 05 1 0 0 0 -1
04 06 1 0 0 0 -1
04 07 1 0 0 0 -1
04 08 1 0 0 0 -1
04 09 1 0 0 0 -1
04 10 1 0 0 0 -1
04 11 1 0 0 0 -1
04 12 1 0 0 0 -1
04 13 1 0 0 0 -1
04 14 1 0 0 0 -1
04 15 1 0 0 0 -1
04 16 1 0 0 0 -1
04 17 1 0 0 0 -1
04 18 1 0 0 0 -1
04 19 1 0 0 0 -1
04 20 1 0 0 0 -1
04 21 1 0 0 0 -1
04 22 1 0 0 0 -1
04 23 1 0 0 0 -1
04 24 1 0 0 0 -1
04 25 1 0 0 0 -1
04 26 1 0 0 0 -1
04 27 1 0 0 0 -1
04 28 1 0 0 0 -1
04 29 1 0 0 0 -1
04 30 1 0 0 0 -1
04 31 1 0 0 0 -1
04 32 1 0 0 0 -1
04 33 1 0 0 0 -1
04 34 1 0 0 0 -1
04 35 1 0 0 0 -1
04 36 1 0 0 0 -1
04 37 1 0 0 0 -1
... 1627 more lines ...
|
| Attachment 3: matrix_config_piggy.txt
|
# Config-File of the Pixel-Matrix; generated by MPW3-Config-Creator
# each line represents the configuration of an individual pixel
# format: {row} {col} {mask} {en_inj} {hb_en} {en_sfout} {TDAC}
# default values (which are not printed) are:
# {row} {col} 0 0 0 0 -1
00 00 1 0 0 0 -1
00 01 1 0 0 0 -1
00 02 1 0 0 0 -1
00 03 1 0 0 0 -1
00 04 1 0 0 0 -1
00 05 1 0 0 0 -1
00 06 1 0 0 0 -1
00 07 1 0 0 0 -1
00 08 1 0 0 0 -1
00 09 1 0 0 0 -1
00 10 1 0 0 0 -1
00 11 1 0 0 0 -1
00 12 1 0 0 0 -1
00 13 1 0 0 0 -1
00 14 1 0 0 0 -1
00 15 1 0 0 0 -1
00 16 1 0 0 0 -1
00 17 1 0 0 0 -1
00 18 1 0 0 0 -1
00 19 1 0 0 0 -1
00 20 1 0 0 0 -1
00 21 1 0 0 0 -1
00 22 1 0 0 0 -1
00 23 1 0 0 0 -1
00 24 1 0 0 0 -1
00 25 1 0 0 0 -1
00 26 1 0 0 0 -1
00 27 1 0 0 0 -1
00 28 1 0 0 0 -1
00 29 1 0 0 0 -1
00 30 1 0 0 0 -1
00 31 1 0 0 0 -1
00 32 1 0 0 0 -1
00 33 1 0 0 0 -1
00 34 1 0 0 0 -1
00 35 1 0 0 0 -1
00 36 1 0 0 0 -1
00 37 1 0 0 0 -1
00 38 1 0 0 0 -1
00 39 1 0 0 0 -1
00 40 1 0 0 0 -1
00 41 1 0 0 0 -1
00 42 1 0 0 0 -1
00 43 1 0 0 0 -1
00 44 1 0 0 0 -1
00 45 1 0 0 0 -1
00 46 1 0 0 0 -1
00 47 1 0 0 0 -1
00 48 1 0 0 0 -1
00 49 1 0 0 0 -1
00 50 1 0 0 0 -1
00 51 1 0 0 0 -1
00 52 1 0 0 0 -1
00 53 1 0 0 0 -1
00 54 1 0 0 0 -1
00 55 1 0 0 0 -1
00 56 1 0 0 0 -1
00 57 1 0 0 0 -1
00 58 1 0 0 0 -1
00 59 1 0 0 0 -1
00 60 1 0 0 0 -1
00 61 1 0 0 0 -1
00 62 1 0 0 0 -1
00 63 1 0 0 0 -1
01 00 1 0 0 0 -1
01 01 1 0 0 0 -1
01 02 1 0 0 0 -1
01 03 1 0 0 0 -1
01 04 1 0 0 0 -1
01 05 1 0 0 0 -1
01 06 1 0 0 0 -1
01 07 1 0 0 0 -1
01 08 1 0 0 0 -1
01 09 1 0 0 0 -1
01 10 1 0 0 0 -1
01 11 1 0 0 0 -1
01 12 1 0 0 0 -1
01 13 1 0 0 0 -1
01 14 1 0 0 0 -1
01 15 1 0 0 0 -1
01 16 1 0 0 0 -1
01 17 1 0 0 0 -1
01 18 1 0 0 0 -1
01 19 1 0 0 0 -1
01 20 1 0 0 0 -1
01 21 1 0 0 0 -1
01 22 1 0 0 0 -1
01 23 1 0 0 0 -1
01 24 1 0 0 0 -1
01 25 1 0 0 0 -1
01 26 1 0 0 0 -1
01 27 1 0 0 0 -1
01 28 1 0 0 0 -1
01 29 1 0 0 0 -1
01 30 1 0 0 0 -1
01 31 1 0 0 0 -1
01 32 1 0 0 0 -1
01 33 1 0 0 0 -1
01 34 1 0 0 0 -1
01 35 1 0 0 0 -1
01 36 1 0 0 0 -1
01 37 1 0 0 0 -1
01 38 1 0 0 0 -1
01 39 1 0 0 0 -1
01 40 1 0 0 0 -1
01 41 1 0 0 0 -1
01 42 1 0 0 0 -1
01 43 1 0 0 0 -1
01 44 1 0 0 0 -1
01 45 1 0 0 0 -1
01 46 1 0 0 0 -1
01 47 1 0 0 0 -1
01 48 1 0 0 0 -1
01 49 1 0 0 0 -1
01 50 1 0 0 0 -1
01 51 1 0 0 0 -1
01 52 1 0 0 0 -1
01 53 1 0 0 0 -1
01 54 1 0 0 0 -1
01 55 1 0 0 0 -1
01 56 1 0 0 0 -1
01 57 1 0 0 0 -1
01 58 1 0 0 0 -1
01 59 1 0 0 0 -1
01 60 1 0 0 0 -1
01 61 1 0 0 0 -1
01 62 1 0 0 0 -1
01 63 1 0 0 0 -1
02 00 1 0 0 0 -1
02 01 1 0 0 0 -1
02 02 1 0 0 0 -1
02 03 1 0 0 0 -1
02 04 1 0 0 0 -1
02 05 1 0 0 0 -1
02 06 1 0 0 0 -1
02 07 1 0 0 0 -1
02 08 1 0 0 0 -1
02 09 1 0 0 0 -1
02 10 1 0 0 0 -1
02 11 1 0 0 0 -1
02 12 1 0 0 0 -1
02 13 1 0 0 0 -1
02 14 1 0 0 0 -1
02 15 1 0 0 0 -1
02 16 1 0 0 0 -1
02 17 1 0 0 0 -1
02 18 1 0 0 0 -1
02 19 1 0 0 0 -1
02 20 1 0 0 0 -1
02 21 1 0 0 0 -1
02 22 1 0 0 0 -1
02 23 1 0 0 0 -1
02 24 1 0 0 0 -1
02 25 1 0 0 0 -1
02 26 1 0 0 0 -1
02 27 1 0 0 0 -1
02 28 1 0 0 0 -1
02 29 1 0 0 0 -1
02 30 1 0 0 0 -1
02 31 1 0 0 0 -1
02 32 1 0 0 0 -1
02 33 1 0 0 0 -1
02 34 1 0 0 0 -1
02 35 1 0 0 0 -1
02 36 1 0 0 0 -1
02 37 1 0 0 0 -1
02 38 1 0 0 0 -1
02 39 1 0 0 0 -1
02 40 1 0 0 0 -1
02 41 1 0 0 0 -1
02 42 1 0 0 0 -1
02 43 1 0 0 0 -1
02 44 1 0 0 0 -1
02 45 1 0 0 0 -1
02 46 1 0 0 0 -1
02 47 1 0 0 0 -1
02 48 1 0 0 0 -1
02 49 1 0 0 0 -1
02 50 1 0 0 0 -1
02 51 1 0 0 0 -1
02 52 1 0 0 0 -1
02 53 1 0 0 0 -1
02 54 1 0 0 0 -1
02 55 1 0 0 0 -1
02 56 1 0 0 0 -1
02 57 1 0 0 0 -1
02 58 1 0 0 0 -1
02 59 1 0 0 0 -1
02 60 1 0 0 0 -1
02 61 1 0 0 0 -1
02 62 1 0 0 0 -1
02 63 1 0 0 0 -1
03 00 1 0 0 0 -1
03 01 1 0 0 0 -1
03 02 1 0 0 0 -1
03 03 1 0 0 0 -1
03 04 1 0 0 0 -1
03 05 1 0 0 0 -1
03 06 1 0 0 0 -1
03 07 1 0 0 0 -1
03 08 1 0 0 0 -1
03 09 1 0 0 0 -1
03 10 1 0 0 0 -1
03 11 1 0 0 0 -1
03 12 1 0 0 0 -1
03 13 1 0 0 0 -1
03 14 1 0 0 0 -1
03 15 1 0 0 0 -1
03 16 1 0 0 0 -1
03 17 1 0 0 0 -1
03 18 1 0 0 0 -1
03 19 1 0 0 0 -1
03 20 1 0 0 0 -1
03 21 1 0 0 0 -1
03 22 1 0 0 0 -1
03 23 1 0 0 0 -1
03 24 1 0 0 0 -1
03 25 1 0 0 0 -1
03 26 1 0 0 0 -1
03 27 1 0 0 0 -1
03 28 1 0 0 0 -1
03 29 1 0 0 0 -1
03 30 1 0 0 0 -1
03 31 1 0 0 0 -1
03 32 1 0 0 0 -1
03 33 1 0 0 0 -1
03 34 1 0 0 0 -1
03 35 1 0 0 0 -1
03 36 1 0 0 0 -1
03 37 1 0 0 0 -1
03 38 1 0 0 0 -1
03 39 1 0 0 0 -1
03 40 1 0 0 0 -1
03 41 1 0 0 0 -1
03 42 1 0 0 0 -1
03 43 1 0 0 0 -1
03 44 1 0 0 0 -1
03 45 1 0 0 0 -1
03 46 1 0 0 0 -1
03 47 1 0 0 0 -1
03 48 1 0 0 0 -1
03 49 1 0 0 0 -1
03 50 1 0 0 0 -1
03 51 1 0 0 0 -1
03 52 1 0 0 0 -1
03 53 1 0 0 0 -1
03 54 1 0 0 0 -1
03 55 1 0 0 0 -1
03 56 1 0 0 0 -1
03 57 1 0 0 0 -1
03 58 1 0 0 0 -1
03 59 1 0 0 0 -1
03 60 1 0 0 0 -1
03 61 1 0 0 0 -1
03 62 1 0 0 0 -1
03 63 1 0 0 0 -1
04 00 1 0 0 0 -1
04 01 1 0 0 0 -1
04 02 1 0 0 0 -1
04 03 1 0 0 0 -1
04 04 1 0 0 0 -1
04 05 1 0 0 0 -1
04 06 1 0 0 0 -1
04 07 1 0 0 0 -1
04 08 1 0 0 0 -1
04 09 1 0 0 0 -1
04 10 1 0 0 0 -1
04 11 1 0 0 0 -1
04 12 1 0 0 0 -1
04 13 1 0 0 0 -1
04 14 1 0 0 0 -1
04 15 1 0 0 0 -1
04 16 1 0 0 0 -1
04 17 1 0 0 0 -1
04 18 1 0 0 0 -1
04 19 1 0 0 0 -1
04 20 1 0 0 0 -1
04 21 1 0 0 0 -1
04 22 1 0 0 0 -1
04 23 1 0 0 0 -1
04 24 1 0 0 0 -1
04 25 1 0 0 0 -1
04 26 1 0 0 0 -1
04 27 1 0 0 0 -1
04 28 1 0 0 0 -1
04 29 1 0 0 0 -1
04 30 1 0 0 0 -1
04 31 1 0 0 0 -1
04 32 1 0 0 0 -1
04 33 1 0 0 0 -1
04 34 1 0 0 0 -1
04 35 1 0 0 0 -1
04 36 1 0 0 0 -1
04 37 1 0 0 0 -1
... 1628 more lines ...
|
| Attachment 4: mpw3.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000010 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DDACThreshold0 = -0.025 #-0.025 #-0.012
DACThreshold1 = -0.012 #-0.025 #-0.012
DACThreshold2 = +0.5
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0xC0 #0x00
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x3= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
DUTIgnoreBusy= 0xF #ignores triggers
DUTIgnoreShutterVeto= 0x0
EnableRecordData = 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/testbeam_data/maus_231014/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW3_0]
[Producer.elog1]
start_cmd = ./scp_configs.sh
files2log = peary.cfg, matrix_config_base.txt, matrix_config_piggy.txt, mpw3.conf
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /media/silicon/testbeam_data/maus_231014/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
|
|
23
|
Sun Feb 19 00:38:25 2023 |
BP_PS | beam | 16 | common | 800 | 5kHz | Proton | 1180283 | Unknown | 19.02.2023 00:35:51 | 19.02.2023 00:38:25 | | | | automatic log for run 16 |
| Attachment 1: mpw3.conf
|
# example config file: Ex0.conf
[RunControl]
pCT_STOP_RUN_AFTER_N_SECONDS = 100
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
#DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
#DUTMaskMode= 0x0c
#DUTMaskMode= 0xFF
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[Producer.tracker_irgendwas]
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/work/mpw3/testbeam/maus_20230218/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/work/mpw3/testbeam/maus_20230218/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
|
|
22
|
Sun Feb 19 00:35:07 2023 |
BP_PS | beam | 15 | common | 800 | 5kHz | Proton | 965511 | Unknown | 19.02.2023 00:32:58 | 19.02.2023 00:35:07 | | | | automatic log for run 15 |
| Attachment 1: mpw3.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
#DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
#DUTMaskMode= 0x0c
#DUTMaskMode= 0xFF
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[Producer.tracker_irgendwas]
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/work/mpw3/testbeam/maus_20230218/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/work/mpw3/testbeam/maus_20230218/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
|
|
21
|
Sun Feb 19 00:32:49 2023 |
BP_PS | beam | 14 | common | 800 | 5kHz | Proton | 3313269 | Unknown | 19.02.2023 00:26:08 | 19.02.2023 00:32:49 | | | | automatic log for run 14 |
| Attachment 1: mpw3.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
#DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
#DUTMaskMode= 0x0c
#DUTMaskMode= 0xFF
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[Producer.tracker_irgendwas]
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/work/mpw3/testbeam/maus_20230218/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/work/mpw3/testbeam/maus_20230218/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
|
|
20
|
Sun Feb 19 00:25:54 2023 |
BP_PS | beam | 13 | common | 800 | 5kHz | Proton | 798582 | Unknown | 19.02.2023 00:24:06 | 19.02.2023 00:25:54 | | | | automatic log for run 13 |
| Attachment 1: mpw3.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
#DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
#DUTMaskMode= 0x0c
#DUTMaskMode= 0xFF
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[Producer.tracker_irgendwas]
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/work/mpw3/testbeam/maus_20230218/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/work/mpw3/testbeam/maus_20230218/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
|
|
178
|
Sat May 6 21:58:14 2023 |
| | 124 | common | 800 | 5kHz | Proton | 306082 | Good | 06.05.2023 21:50:04 | 06.05.2023 21:57:21 | | Normal | automatic log for run 124
Comment:
Alignment run low flux |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
#VCLIP = 190
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 20
VRESET = 140
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
177
|
Sat May 6 21:46:56 2023 |
| | 123 | common | 800 | 5kHz | Proton | 2987729 | Unknown | 06.05.2023 21:41:37 | 06.05.2023 21:46:04 | | Normal | automatic log for run 123
Comment: |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
#VCLIP = 190
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 20
VRESET = 140
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
176
|
Sat May 6 21:39:32 2023 |
| | 122 | common | 800 | 200kHz | Proton | 121791 | Crap | 06.05.2023 21:38:22 | 06.05.2023 21:38:40 | | Normal | automatic log for run 122
Comment:
ICAN 20 |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
#VCLIP = 190
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
ICASN = 20
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
175
|
Sat May 6 21:38:19 2023 |
| | 121 | common | 800 | 200kHz | Proton | 2732840 | Good | 06.05.2023 21:33:33 | 06.05.2023 21:37:27 | | Normal | automatic log for run 121
Comment:
VCLIP? |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
#VCLIP = 190
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
174
|
Sat May 6 21:33:17 2023 |
| | 120 | common | 800 | 200kHz | Proton | 1543284 | Good | 06.05.2023 21:30:08 | 06.05.2023 21:32:25 | | Normal | automatic log for run 120
Comment:
VCLIP 220 |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
VCLIP = 175
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
19
|
Sun Feb 19 00:23:30 2023 |
BP_PS | beam | 12 | common | 800 | 5kHz | Proton | 786240 | Unknown | 19.02.2023 00:21:45 | 19.02.2023 00:23:30 | | | | automatic log for run 12 |
| Attachment 1: mpw3.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
#DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
#DUTMaskMode= 0x0c
#DUTMaskMode= 0xFF
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[Producer.tracker_irgendwas]
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/work/mpw3/testbeam/maus_20230218/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/work/mpw3/testbeam/maus_20230218/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
|
|
173
|
Sat May 6 21:30:02 2023 |
| | 119 | common | 800 | 200kHz | Proton | 7663968 | Good | 06.05.2023 21:18:32 | 06.05.2023 21:29:09 | | Normal | automatic log for run 119
Comment:
Alignment run with default settings |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
VCLIP = 220
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
172
|
Sat May 6 21:17:01 2023 |
| | 118 | common | 800 | 200kHz | Proton | 1379570 | Good | 06.05.2023 21:14:09 | 06.05.2023 21:16:09 | | Normal | automatic log for run 118
Comment:
VCLIP 180 |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
#CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
#CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
#VCLIP = 220
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
171
|
Sat May 6 21:13:46 2023 |
| | 117 | common | 800 | 200kHz | Proton | 1670098 | Good | 06.05.2023 21:10:32 | 06.05.2023 21:12:54 | | Normal | automatic log for run 117
Comment:
VCLIP 170 |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
VCLIP = 180
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
170
|
Sat May 6 21:10:23 2023 |
| | 116 | common | 800 | 200kHz | Proton | 145044 | Good | 06.05.2023 21:09:10 | 06.05.2023 21:09:31 | | Normal | automatic log for run 116
Comment:
VCLIP 200 |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
VCLIP = 170
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
169
|
Sat May 6 21:09:10 2023 |
| | 115 | common | 800 | 200kHz | Proton | 1634138 | Good | 06.05.2023 21:06:04 | 06.05.2023 21:08:17 | | Normal | automatic log for run 115
Comment:
VCLIP 200 |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
VCLIP = 170
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
168
|
Sat May 6 21:04:50 2023 |
| | 114 | common | 800 | 200kHz | Proton | 349320 | Good | 06.05.2023 21:03:24 | 06.05.2023 21:03:58 | | Normal | automatic log for run 114
Comment:
VCLIP 200 |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
VCLIP = 200
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
167
|
Sat May 6 21:01:39 2023 |
| | 113 | common | 800 | 200kHz | Proton | 999866 | Good | 06.05.2023 20:59:22 | 06.05.2023 21:00:47 | | Normal | automatic log for run 113
Comment:
VCLIP 110 |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
VCLIP = 120
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
166
|
Sat May 6 20:59:29 2023 |
| | 112 | common | 800 | 200kHz | Proton | 1176044 | Good | 06.05.2023 20:56:59 | 06.05.2023 20:58:36 | | Normal | automatic log for run 112
Comment:
VCLIP 100 |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
VCLIP = 110
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
165
|
Sat May 6 20:56:58 2023 |
| | 111 | common | 800 | Low Flux Low | Proton | 7293463 | Unknown | 06.05.2023 20:46:13 | 06.05.2023 20:56:06 | | Normal | automatic log for run 111
Comment:
VCLIP 130 (first one run with data since a while ago, also longer for alignment) |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
VCLIP = 100
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|