| ID |
Date |
Author |
Subject |
Run Number |
DUT |
Beam Energy |
Rate Setting |
Particle Type |
Events |
Data |
t-Start |
t-Stop |
Duration_min |
Frontend |
|
48
|
Sun Feb 19 04:20:21 2023 |
BP_PS | beam | 39 | RD50-MPW3 | 800 | 200kHz | Proton | 4127604 | Unknown | 19.02.2023 04:10:54 | 19.02.2023 04:20:21 | | | | automatic log for run 39 |
| Attachment 1: mpw3.conf
|
# example config file: Ex0.conf
[RunControl]
pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
#DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
#DUTMaskMode= 0x0c
#DUTMaskMode= 0xFF
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[Producer.tracker_irgendwas]
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
#EUDAQ_FW_PATTERN= /home/silicon/work/mpw3/testbeam/maus_20230218/tlu_run$6R$X
EUDAQ_FW_PATTERN= /media/silicon/maus/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/mpw3/testbeam/maus_20230218/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/maus/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 10
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
|
|
133
|
Sat May 6 16:43:35 2023 |
TB crew | MPX2 MPW3 TB | 79 | RD50-MPW3 | 175.3 | Low Flux Medium | Proton | 4106269 | Good | 06.05.2023 16:37:53 | 06.05.2023 16:42:43 | | Normal Casc | automatic log for run 79
Comment:
VCLIP 150 |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalCascFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 336
STOP_COLUMN = 448
WAIT_FOR_FPGA = 1
#chip register config
VCLIP = 150
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
132
|
Sat May 6 16:37:40 2023 |
TB crew | MPX2 MPW3 TB | 78 | RD50-MPW3 | 175.3 | Low Flux Medium | Proton | 4053764 | Good | 06.05.2023 16:31:33 | 06.05.2023 16:36:48 | | Normal Casc | automatic log for run 78
Comment: |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalCascFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 336
STOP_COLUMN = 448
WAIT_FOR_FPGA = 1
#chip register config
#VCLIP = 255
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
127
|
Sat May 6 15:58:49 2023 |
TB crew | MPX2 MPW3 TB | 73 | RD50-MPW3 | 800 | 200kHz | Proton | 3897223 | Good | 06.05.2023 15:52:19 | 06.05.2023 15:57:58 | | Normal Casc | automatic log for run 73
Comment: |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalCascFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 336
STOP_COLUMN = 448
WAIT_FOR_FPGA = 1
#chip register config
VCLIP = 50
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
144
|
Sat May 6 18:52:10 2023 |
| | 90 | common | 800 | Low Flux Low | Proton | 36435245 | Good | 06.05.2023 18:01:47 | 06.05.2023 18:51:18 | | Normal | automatic log for run 90
Comment: |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
VCLIP = 250
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
29
|
Sun Feb 19 01:31:35 2023 |
BP_PS | beam | 22 | common | 800 | 5kHz | Proton | 3527769 | Unknown | 19.02.2023 01:23:58 | 19.02.2023 01:31:34 | | | | automatic log for run 22 |
| Attachment 1: mpw3.conf
|
# example config file: Ex0.conf
[RunControl]
pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
#DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
#DUTMaskMode= 0x0c
#DUTMaskMode= 0xFF
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[Producer.tracker_irgendwas]
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/work/mpw3/testbeam/maus_20230218/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/work/mpw3/testbeam/maus_20230218/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
|
|
168
|
Sat May 6 21:04:50 2023 |
| | 114 | common | 800 | 200kHz | Proton | 349320 | Good | 06.05.2023 21:03:24 | 06.05.2023 21:03:58 | | Normal | automatic log for run 114
Comment:
VCLIP 200 |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
VCLIP = 200
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
45
|
Sun Feb 19 04:07:11 2023 |
BP_PS | beam | 36 | RD50-MPW3 | 800 | 200kHz | Proton | 342134 | Unknown | 19.02.2023 04:05:44 | 19.02.2023 04:07:11 | | | | automatic log for run 36 |
| Attachment 1: mpw3.conf
|
# example config file: Ex0.conf
[RunControl]
pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
#DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
#DUTMaskMode= 0x0c
#DUTMaskMode= 0xFF
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[Producer.tracker_irgendwas]
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
#EUDAQ_FW_PATTERN= /home/silicon/work/mpw3/testbeam/maus_20230218/tlu_run$6R$X
EUDAQ_FW_PATTERN= /media/silicon/maus/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/mpw3/testbeam/maus_20230218/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/maus/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
|
|
21
|
Sun Feb 19 00:32:49 2023 |
BP_PS | beam | 14 | common | 800 | 5kHz | Proton | 3313269 | Unknown | 19.02.2023 00:26:08 | 19.02.2023 00:32:49 | | | | automatic log for run 14 |
| Attachment 1: mpw3.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
#DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
#DUTMaskMode= 0x0c
#DUTMaskMode= 0xFF
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[Producer.tracker_irgendwas]
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/work/mpw3/testbeam/maus_20230218/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/work/mpw3/testbeam/maus_20230218/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
|
|
137
|
Sat May 6 17:08:40 2023 |
TB crew | MPX2 MPW3 TB | 83 | RD50-MPW3 | 100.4 | Low Flux Medium | Proton | 3272369 | Good | 06.05.2023 17:02:29 | 06.05.2023 17:07:49 | | Normal Casc | automatic log for run 83
Comment: |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalCascFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 336
STOP_COLUMN = 448
WAIT_FOR_FPGA = 1
#chip register config
VCLIP = 150
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
152
|
Sat May 6 19:42:31 2023 |
| | 98 | common | 800 | 200kHz | Proton | 314807 | Crap | 06.05.2023 19:20:43 | 06.05.2023 19:41:39 | | Normal | automatic log for run 98
Comment:
VCLIP 190 |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
VCLIP = 190
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
140
|
Sat May 6 17:28:18 2023 |
TB crew | MPX2 MPW3 TB | 86 | RD50-MPW3 | 83 | Low Flux Medium | Proton | 3144767 | Good | 06.05.2023 17:22:31 | 06.05.2023 17:27:26 | | Normal Casc | automatic log for run 86
Comment: |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalCascFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 336
STOP_COLUMN = 448
WAIT_FOR_FPGA = 1
#chip register config
#VCLIP = 150
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
164
|
Sat May 6 20:42:17 2023 |
| | 110 | common | 800 | 200kHz | Proton | 3100010 | Good | 06.05.2023 20:36:59 | 06.05.2023 20:41:24 | | Normal | automatic log for run 110
Comment:
VCLIP 135 |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
VCLIP = 130
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
178
|
Sat May 6 21:58:14 2023 |
| | 124 | common | 800 | 5kHz | Proton | 306082 | Good | 06.05.2023 21:50:04 | 06.05.2023 21:57:21 | | Normal | automatic log for run 124
Comment:
Alignment run low flux |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
#VCLIP = 190
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 20
VRESET = 140
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
177
|
Sat May 6 21:46:56 2023 |
| | 123 | common | 800 | 5kHz | Proton | 2987729 | Unknown | 06.05.2023 21:41:37 | 06.05.2023 21:46:04 | | Normal | automatic log for run 123
Comment: |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
#VCLIP = 190
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 20
VRESET = 140
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
139
|
Sat May 6 17:22:40 2023 |
TB crew | MPX2 MPW3 TB | 85 | RD50-MPW3 | 83 | Low Flux Medium | Proton | 2779147 | Good | 06.05.2023 17:16:25 | 06.05.2023 17:21:48 | | Normal Casc | automatic log for run 85
Comment:
VCLIP 150 |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalCascFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 336
STOP_COLUMN = 448
WAIT_FOR_FPGA = 1
#chip register config
#VCLIP = 150
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
175
|
Sat May 6 21:38:19 2023 |
| | 121 | common | 800 | 200kHz | Proton | 2732840 | Good | 06.05.2023 21:33:33 | 06.05.2023 21:37:27 | | Normal | automatic log for run 121
Comment:
VCLIP? |
| Attachment 1: mpw3_mpx2.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
pCT_STOP_RUN_AFTER_N_SECONDS = 120
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[Producer.tracker_irgendwas]
################################### TLU #####################################
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 0
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 0
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
DUTMask= 0xE #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #DUT3 in AIDA mode, rest in EUDET mode
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
EnableRecordData = 1
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
################################### MPW3 #####################################
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/testbeam/maus_230505/test/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
SYNC_MODE = 1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
################################### MPX2 #####################################
[Producer.monopix2]
# connection to the data collector
EUDAQ_DC = mpx2_dc
ENABLE_BDAQ_RECORD = 1
ENABLE_HITOR = 1
CHIP_CONFIG_FILE = /home/rd50/tjmonopix2/ChipSettings/THR26_NormalFE.h5
CHIP_SN = W8R19
CHIP_CMD_CLK = 86.8 # 160.0
#overriding values in "scan_configuration"
#when none given default ones are being used
START_ROW = 0
STOP_ROW = 512
START_COLUMN = 0
STOP_COLUMN = 158
WAIT_FOR_FPGA = 1
#chip register config
#VCLIP = 190
#VL = 30
#VH = 150
#ITHR = 30
#IBIAS = 60
#VCASP = 40
#ICASN = 8
#VRESET = 95
#IDB = 250
#MASKED_PIXELS_FILE = /mnt/data/monopix2/tj-monopix2-daq/tjmonopix2/scans/masked_pixels.yaml
[Producer.hameg]
#HV = 5
BIAS = 6
SERIAL_PORT = /dev/ttyUSB0
[Monitor.monopix2_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
[DataCollector.mpx2_dc]
# connection to the monitor
EUDAQ_MN = monopix2_mon
EUDAQ_FW = native
#path to store .raw file to, $3R is replaced by 3 digit run number, $12D -> 12 character date, $X -> .raw
EUDAQ_FW_PATTERN = /media/silicon/15cb8462-c19d-408a-9e21-4154280cb15a/maus_230507/mpx2_run$6R$X
#fraction of events being sent to the monitor
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
#disable output of event to bash, is spamming terminal otherwise
DISABLE_PRINT = 1
|
|
15
|
Sat Feb 18 23:38:40 2023 |
BP_PS | beam | 9 | common | 800 | 5kHz | Proton | 2714936 | Unknown | 18.02.2023 23:33:15 | 18.02.2023 23:38:40 | | | | automatic log for run 9 |
| Attachment 1: mpw3.conf
|
# example config file: Ex0.conf
[RunControl]
#pCT_STOP_RUN_AFTER_N_SECONDS = 3000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
#DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
#DUTMaskMode= 0x0c
#DUTMaskMode= 0xFF
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[Producer.tracker_irgendwas]
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/work/mpw3/testbeam/maus_20230218/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/work/mpw3/testbeam/maus_20230218/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
|
|
26
|
Sun Feb 19 00:47:46 2023 |
BP_PS | beam | 19 | common | 800 | 5kHz | Proton | 2516208 | Unknown | 19.02.2023 00:42:43 | 19.02.2023 00:47:46 | | | | automatic log for run 19 |
| Attachment 1: mpw3.conf
|
# example config file: Ex0.conf
[RunControl]
pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
#DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
#DUTMaskMode= 0x0c
#DUTMaskMode= 0xFF
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[Producer.tracker_irgendwas]
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
EUDAQ_FW_PATTERN= /home/silicon/work/mpw3/testbeam/maus_20230218/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
EUDAQ_FW_PATTERN = /home/silicon/work/mpw3/testbeam/maus_20230218/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
|
|
43
|
Sun Feb 19 03:35:01 2023 |
| beam | 34 | RD50-MPW3 | 800 | 200kHz | Proton | 2514361 | Unknown | 19.02.2023 03:29:00 | 19.02.2023 03:35:01 | | | | automatic log for run 34 |
| Attachment 1: mpw3.conf
|
# example config file: Ex0.conf
[RunControl]
pCT_STOP_RUN_AFTER_N_SECONDS = 10000000000000
# from the base RunControl.cc
#EUDAQ_CTRL_PRODUCER_LAST_START = my_pd0
#EUDAQ_CTRL_PRODUCER_FIRST_STOP = my_pd0
# Steer which values to display in the GUI: producerName and displayed value are seperated by a ",".
ADDITIONAL_DISPLAY_NUMBERS = "log,_SERVER"
[Producer.aida_tlu]
## GENERAL PARAMETERS
verbose= 1
skipconf= 0
confid= 20201311
delayStart= 200
## HDMI CONFIGURATION
# 4-bits to determine direction of HDMI pins
HDMI1_set= 0x7 #1= output (driven by TLU), 0 = input. bit 0=CONT, 1=SPARE, 2=TRIG, 3=BUSY for eudet, Busy needs to be 0. (0b0111 = 0x7)
HDMI2_set= 0x7
HDMI3_set= 0x7
HDMI4_set= 0x7
# Clock source (0= no clock, 1= Si5345, 2= FPGA)
HDMI1_clk = 1
HDMI2_clk = 1
HDMI3_clk = 1
HDMI4_clk = 1
# Enable/Disable clock on differential LEMO
LEMOclk = 0
## PMT POWER CONFIGURATION
PMT1_V= 0.6363 #Szinti 4x4cm
PMT2_V= 0.6363 #Szinti 4x4cm
PMT3_V= 0.0
PMT4_V= 0.0
## TRIGGER CONFIGURATION
trigMaskHi = 0x00000000
trigMaskLo = 0x00000008 #0x00010002 #0x00000001 #8 coinc1+2
in0_STR = 0 # 0
in0_DEL = 0 # 18
in1_STR = 0 # 0
in1_DEL = 0 # 18
in2_STR = 0 # 0
in2_DEL = 0 # 0
in3_STR = 0
in3_DEL = 0
in4_STR = 0
in4_DEL = 0
in5_STR = 0 #streches pulse from 6.25ns (at 0) to 12.5ns
in5_DEL = 0
# Generate internal triggers (in Hz, 0= no triggers)
InternalTriggerFreq= 0 #4000 #00
## DISCRIMINATOR THRESHOLDS
DACThreshold0 = -0.025 #-0.012
DACThreshold1 = -0.025 #-0.012
DACThreshold2 = -0.12
DACThreshold3 = -0.12
DACThreshold4 = -0.12 #-0.0066
DACThreshold5 = -0.12
## DUT CONFIGURATION
# DUTMask Which DUTs are on
#DUTMask= 0x3 #6 bit 0= DUT1, bit 1= DUT2, bit 2= DUT3, bit 3= DUT4
DUTMask= 0x6
#DUTMask= 0xF
# DUTMaskMode Define AIDA (11) or EUDET (00) mode (2 bits per DUT)
DUTMaskMode= 0x30 #0x00
#DUTMaskMode= 0x0c
#DUTMaskMode= 0xFF
# In EUDET mode: 0 = standard trigger/busy mode, 1 = raising BUSY outside handshake vetoes triggers (2 bits per DUT, 0x03= DUT 4! -backwards!)
DUTMaskModeModifier= 0x30 #0x30 #0xC0 PS: Check what this does! 0x0 würde ich hier eingeben
# Ignore the BUSY signal for a DUT (0xF)
#DUTIgnoreBusy= 0x4 #ignores triggers
DUTIgnoreBusy= 0x0
DUTIgnoreShutterVeto= 0x0
EnableRecordData= 1
# EnableShutterMode: 0x0. If 1, shutter mode is enabled. If 0, shutter mode is disabled.
EnableShutterMode= 0x0
# Define which input is used for shutter source [0 - 5]
ShutterSource = 5
# 32-bit counter of clocks. Set to 0 to not use internal shutter generator.
InternalShutterInterval = 0
# 32-bit counter of clocks
ShutterOnTime = 0 #start of shutter after trigger
# 32-bit counter of clocks
ShutterVetoOffTime = 0 #time after input-trigger, until first trigger is sent to output
# 32-bit counter of clocks
ShutterOffTime = 200000000 #end of shutter after trigger #200000000 = 5s (multiples of 25ns)
## DATA COLLECTOR
EUDAQ_DC= tlu_dc
## TLU MONITOR PARAMETER
FileComment="mpw3"
PlotWindowSizeinns=40e9
MinSpillTimeOnins=4.5
MinSpilldownTimeins=0.5
ThreshEvBegin=1
ThreshEvEnd=1
ThreshPartBegin=1
ThreshPartEnd=1
[Producer.tracker_irgendwas]
[LogCollector.log]
# Currently, all LogCollectors have a hardcoded runtime name: log
# nothing
[DataCollector.tlu_dc]
EUDAQ_FW=native
# the format of data file
#EUDAQ_FW_PATTERN= /home/silicon/work/mpw3/testbeam/maus_20230218/tlu_run$6R$X
EUDAQ_FW_PATTERN= /media/silicon/maus/tlu_run$6R$X
# the name pattern of data file
# the $12D will be converted a data/time string with 12 digits.
# the $6R will be converted a run number string with 6 digits.
# the $X will be converted the suffix name of data file.
DISABLE_PRINT = 1
[Producer.RD50_MPW3]
[DataCollector.mpw3_dc]
# connection to the monitor
EUDAQ_MN = mpw3_mon
EUDAQ_FW = native
#EUDAQ_FW_PATTERN = /home/silicon/work/mpw3/testbeam/maus_20230218/mpw3_run$6R$X
EUDAQ_FW_PATTERN = /media/silicon/maus/mpw3_run$6R$X
EUDAQ_DATACOL_SEND_MONITOR_FRACTION = 100
# config-parameters
DISABLE_PRINT = 1
XILINX_IP = 192.168.201.1
[Monitor.mpw3_mon]
ENABLE_PRINT = 0
ENABLE_STD_PRINT = 0
ENABLE_STD_CONVERTER = 1
FORWARD2GUI = 1
|
|