Telescope in combination with SVD3

room temp, FIRRun002, pedestalrun003, taget FW

update pedestal values for room temp sixlet runs.
 

FIR filer and ADC delay with all sensor and telescope.
Telescope alignment

room temp
pedestalrun 008
FIRRun004

max frame pos = 0. frame

[six]
lvl = 20, 30
lat = 95
sam = 20
grp = 8

firrun003, room temp
 

CE. pedestal run 003. Fir run 002. Room temp

lat = 98

room temp

pedestalrun 003

room temp
FIRRun002,
pedestalrun006;
pedestalrun007
 

room temp, FIRRun001, pedestal run 003

lat = 97 to a greater range of lat scan

Cooled!
FIRRun002, pedestalrun006; temp see attachment in pedestalrun006
 

FIR filer and ADC delay with all sensor and telescope.
telescope n-side switched.

FirRun001, room temp
telescope n-side switched.

PedestalRun001, FIRRun001, room temp
telescope n-side switched.
In order to correct the position change the

room temp max subevent at 2. with lat = 96

Information concerning the SVD3 setup during a beam test

In the beam area setup the whole crate and the power supply with the usual spider cable and the two Keithly 2410 high voltage supplies. Monitoring of the 2410 happens via a NI MAX interface that connects to the GPIB-Ethernet interface and needs to be configured there. The IP and password are noted on the device. The software can be found on heros in medialib/LONGTERM/longterm R3.1_doubleSided as a normal *.vi file. 

Default adresses 16 and 17 as defined in labview, need to figure out on site which is which, if the voltage selected (e.g. 100V) is applied as +50/-50 or if it is applied as +100/-100 before connecting the cables. 

Take a run without dut as well to check the telescope integrity. Without dut in beamline!!!!!

WLAN Router:

SSID: Hephy

password: 20supersecret14

DHCP Range: 192.168.0.200 to 239

Netmask: /24

DNS Server: 192.168.0.254

Gateway: 192.168.0.254

external IP: 128.141.174.109 (für diverse Port Forwardings)

Manuell vergebene IP Adressen bitte unbedingt Benni mitteilen oder/und in der folgenden Tabelle eintragen! 

IP/MAC Zuweisung:

Admin Zugang Wlan Router:

IP: 192.168.0.254

Username: admin

password: Hephy2014

x-Achse: positiv Richtung Saleve (counting room)

y-Achse: positiv Richtung UNTEN!!

position of laddertestbox xy stages:

Rev. Pos (BWD Sensor, BWD, Oben) x= 82.3, y=110.6

Mitte Sensor:

Pos 1: (mitte BWD sensor): x=144.74, y=80.8

Pos 2: (mitte Origami -z): x=269.62, y=80.8

Pos 3: (mitte Origami ce): x=394.42, y=80.8

Pos 4 (mitte FWD Micron Sensor): x=517, y=80.8

Ecke:

Pos 5 (Ecke BWD sensor): x=92.3, y=105.6

Pos 6 (Ecke Origami -z): x=217.18, y=105.6

Pos 7 (Ecke Origami ce): x=342.06, y=105.6

Pos 8 (Ecke FWD sensor): x=467,62, y=56,3 

Pos 9 (Ecke FWD sensor): x=568,33 y=64,48