Home CMS Production Clean room MedAustron HEPHY testbeams old
testbeam-RD50-DESY-Jul2023 testbeam-RD50-CERN-Oct2022 testbeam-DESY-Oct2017 testbeam-DESY-April2017 testbeam-SPS2015 testbeam-SPS2014 testbeam-DESY14 testbeam-SPS12 testbeam-SPS11 testbeam-SPS10 testbeam-SPS09 testbeam-SPS08 LP-TPC
  Belle testbeam at SPS in June 2015, Page 3 of 6  Not logged in ELOG logo
Entry  Wed Jun 10 18:52:34 2015, Hao Yin, Belle II FADC (H6A), Pedestal, 009, 10000, , Yes, Good temperature.PNG
temp: in -22 out -18,
FIRRun004,
Entry  Wed Jun 10 19:07:42 2015, Hao Yin, Belle II FADC (H6A), Hardware, 021, , 5, Yes, Good 
temp: in -23 out -20

FIRRun002,
PedestalRun010,
Entry  Thu Jun 11 11:41:50 2015, Hao Yin, Belle II FADC (H6A), Sixlet Calibration, 011, , , Yes, Good 
cooled
pedestalrun 008
FIRRun004
Entry  Thu Jun 11 11:42:39 2015, Hao Yin, Belle II FADC (H6A), Sixlet Calibration, 012, , , Yes, Good 
cooled until about 400k after that room temp
pedestalrun 009
FIRRun005
Entry  Thu Jun 11 16:35:14 2015, Hao Yin, Belle II FADC (H6A), Hardware, 022, , 5, Yes, Good 
temp: in -23 out -20

FIRRun002,
PedestalRun010,
Entry  Thu Jun 11 16:38:17 2015, Hao Yin, Belle II FADC (H6A), Hardware, 023, , 7, Yes, Good Pos7.PNG
temp: attachment (in 1st col, out 2nd col)

FIRRun002,
PedestalRun010,
Entry  Thu Jun 11 18:01:54 2015, Hao Yin, Belle II FADC (H6A), Hardware, 024, , 6, Yes, Good Pos6.PNG
temp: attachment (in 1st col, out 2nd col)

FIRRun002,
PedestalRun010,
Entry  Thu Jun 11 18:37:11 2015, Hao Yin, Belle II FADC (H6A), Hardware, 025, , 6, Yes, Good pos3.PNG
temp: attachment (in 1st col, out 2nd col)

FIRRun002,
PedestalRun010,
Entry  Fri Jun 12 09:31:58 2015, Hao Yin, Belle II FADC (H6A), FIR, 005, , , Yes, Good 
FIR filer and ADC delay for long sixlet cal run.
Entry  Fri Jun 12 17:00:18 2015, Hao Yin, Belle II FADC (H6A), Pedestal, 011, 10000, , No, Good 
cooled pedestal vaules for long sixlet cal
Entry  Fri Jun 12 17:03:02 2015, Hao Yin, Belle II FADC (H6A), Pedestal, 012, 10000, , No, Good 
room temp
FIRRun002
 
Entry  Fri Jun 12 17:11:45 2015, Hao Yin, Belle II FADC (H6A), Hardware, 026, 50k, 1, No, Good 
room temp

FIRRun002,
PedestalRun012,
Entry  Sat Jun 13 09:09:37 2015, Hao Yin, Belle II FADC (H6A), Hardware, 027, ~200k, 2, No, Good 
room temp

FIRRun002,
PedestalRun012,
Entry  Sat Jun 13 10:07:36 2015, Hao Yin, Belle II FADC (H6A), Hardware, 028, 50k, 4, No, Good 
room temp

FIRRun002,
PedestalRun012,
Entry  Sat Jun 13 13:01:39 2015, Hao Yin, Belle II FADC (H6A), Hardware, 029, , 3, No, Good 
room temp

FIRRun002,
PedestalRun012,
Entry  Sat Jun 13 19:26:26 2015, Hao Yin, Belle II FADC (H6A), Hardware, 030, , 3, No, Good 
room temp

FIRRun002,
PedestalRun012,
Entry  Sat Jun 13 19:29:50 2015, Hao Yin, Belle II FADC (H6A), Hardware, 030, , 1, No, Good 
room temp

FIRRun002,
PedestalRun012,
Entry  Tue May 12 10:27:39 2015, Benedikt Würkner, SVD3 (H6B), Setup information, , , , , Unknown spider-config.jpg
Information concerning the SVD3 setup during a beam test

In the beam area setup the whole crate and the power supply with the usual spider cable and the two Keithly 2410 high voltage supplies.
Monitoring of the 2410 happens via a NI MAX interface that connects to the GPIB-Ethernet interface and needs to be configured there. The IP and password
Entry  Thu Jun 4 18:49:03 2015, Benedikt Würkner, SVD3 (H6B), Setup, , , , , Unknown IMG_20150604_184442.jpgIMG_20150604_184451.jpgIMG_20150604_184516.jpg
 
Entry  Sat Jun 6 16:14:36 2015, Benedikt Würkner, SVD3 (H6B), calibration run and setup information, cal01, , , , Unknown 
Calibration Run with +- 50V Bias with higher compliance since the p-side draws more current than expected (23muA by the MAMBO)

 
ELOG V3.1.5-fc6679b