Home CMS Production Clean room MedAustron HEPHY testbeams old
testbeam-RD50-DESY-Jul2023 testbeam-RD50-CERN-Oct2022 testbeam-DESY-Oct2017 testbeam-DESY-April2017 testbeam-SPS2015 testbeam-SPS2014 testbeam-DESY14 testbeam-SPS12 testbeam-SPS11 testbeam-SPS10 testbeam-SPS09 testbeam-SPS08 LP-TPC
  Belle testbeam at SPS in June 2015, Page 3 of 6  Not logged in ELOG logo
New entries since:Thu Jan 1 01:00:00 1970
ID Date Author Projectdown Subject Run Number Events XYPosition Cooling Data
  84   Wed Jun 10 20:54:36 2015 Benedikt WürknerSVD3 (H6B)Residuals FE-I4 (Upstream)59 10NoGood
  85   Wed Jun 10 21:36:25 2015 Benedikt WürknerSVD3 (H6B)Horizontal Beam Profile Run72500001NoGood

Trying to get a nice plot of the beam profile by only using the and 3 (horizontal)  see http://elog.hephy.at/testbeam-SPS2015/66 for details. 

Pos 1: x=100 mm, y=79 mm (Hits in APV 3 und 8-9 in p-Seite und 14 und 17 in n-Seite )

Producer.TLU Config Change:

  • AndMask=0x8 
  88   Thu Jun 11 15:56:32 2015 Benedikt WürknerSVD3 (H6B)Hardware FEI473200007NoUnknown

RUN WITH SVD3, telescope and FEI4

EUDET Run 73

Mimosa Threshold 6

Pos 7: x= 30.5 mm, y= 79 mm (wide side center)

Upstream FEI4 used, checking if alignment change helped

  91   Thu Jun 11 17:11:40 2015 Benedikt WürknerSVD3 (H6B)Hardware FEI474200008NoUnknown

RUN WITH SVD3, telescope and FEI4

EUDET Run 74

Mimosa Threshold 6

Pos 8: x=136.08 mm, y= 79 mm (narrow side center)

Upstream FEI4 used

  95   Fri Jun 12 16:52:52 2015 Benedikt WürknerSVD3 (H6B)Telescope without DUT76~30k NoGood

Threshold 6

Testrun to see how the telescope behaves without a DUT to test if there is an increased amount of multiple scattering after the aluminum planes of the FW and BW module. 

 

  98   Fri Jun 12 17:08:23 2015 Benedikt WürknerSVD3 (H6B)Telescope with FEI480~30k NoGood

Threshold 6

Testrun to see how the telescope behaves without a DUT to test if there is an increased amount of multiple scattering after the aluminum planes of the FW and BW module. 

This time with the upstream FEI4 plane

  103   Sat Jun 13 16:47:28 2015 Benedikt WürknerSVD3 (H6B)Mimosa threshold with FEI48212000 NoGood

Set mimosa threshold to 5 and recorded with FEI4 upstream

L3 already in sensor but not yet configured. 

Probably to noisy to help much

  104   Sat Jun 13 17:05:35 2015 Benedikt WürknerSVD3 (H6B)L3 with FEI484300001NoGood

L3 sensor at position x: 105, y: 47 hitting apvs: 2&3 on p-side and apv 3 on n-side

  105   Sat Jun 13 18:02:04 2015 Benedikt WürknerSVD3 (H6B)L3 with FEI485700002NoGood

L3 sensor at position x: 115, y: 47 hitting apvs: 2&3 on p-side and apv 3&4 on n-side

  106   Sat Jun 13 19:14:41 2015 Benedikt WürknerSVD3 (H6B)L3 with FEI4867320003NoGood

L3 sensor at position x: 115, y: 57 hitting apvs: 1&2 on p-side and apv 3&4 on n-side

  3   Wed Jun 3 17:23:07 2015 Thomas BergauerBelle II FADC (H6A)XY stage positions    Unknown

x-Achse: positiv Richtung Saleve (counting room)

y-Achse: positiv Richtung UNTEN!!

 

position of laddertestbox xy stages:

Rev. Pos (BWD Sensor, BWD, Oben) x= 82.3, y=110.6

Mitte Sensor:

Pos 1: (mitte BWD sensor): x=144.74, y=80.8

Pos 2: (mitte Origami -z): x=269.62, y=80.8

Pos 3: (mitte Origami ce): x=394.42, y=80.8

Pos 4 (mitte FWD Micron Sensor): x=517, y=80.8

Ecke:

Pos 5 (Ecke BWD sensor): x=92.3, y=105.6

Pos 6 (Ecke Origami -z): x=217.18, y=105.6

Pos 7 (Ecke Origami ce): x=342.06, y=105.6

Pos 8 (Ecke FWD sensor): x=467,62, y=56,3 

Pos 9 (Ecke FWD sensor): x=568,33 y=64,48

  4   Thu Jun 4 14:15:50 2015 Hao YinBelle II FADC (H6A)FIR001   Good

FIR filer and ADC delay with all sensor and telescope.
telescope n-side switched.

  5   Thu Jun 4 14:16:20 2015 Hao YinBelle II FADC (H6A)Pedestal00110000  Good

FirRun001, room temp
telescope n-side switched.

  6   Thu Jun 4 15:12:41 2015 Hao YinBelle II FADC (H6A)Hardware001500001NoGood

PedestalRun001, FIRRun001, room temp
telescope n-side switched.
In order to correct the position change the

  7   Thu Jun 4 18:44:50 2015 Hao YinBelle II FADC (H6A)Hardware002500002NoGood

room temp, FIRRun001, pedestal run 003

  8   Thu Jun 4 18:45:42 2015 Hao YinBelle II FADC (H6A)Pedestal00310000  Good

firrun003, room temp
 

  10   Thu Jun 4 22:07:16 2015 Hao YinBelle II FADC (H6A)Hardware003189k3NoGood

CE. pedestal run 003. Fir run 002. Room temp

  11   Fri Jun 5 08:20:27 2015 Hao YinBelle II FADC (H6A)Hardware004500004NoGood

room temp, FIRRun002, pedestalrun003, taget FW

  12   Fri Jun 5 12:02:29 2015 Hao YinBelle II FADC (H6A)Sixlet Calibration001   Good

room temp max subevent at 2. with lat = 96

  13   Fri Jun 5 12:03:34 2015 Hao YinBelle II FADC (H6A)Sixlet Calibration002   Good

lat = 97 to a greater range of lat scan

ELOG V3.1.5-fc6679b