Home CMS Production Clean room MedAustron HEPHY testbeams old
testbeam-RD50-DESY-Jul2023 testbeam-RD50-CERN-Oct2022 testbeam-DESY-Oct2017 testbeam-DESY-April2017 testbeam-SPS2015 testbeam-SPS2014 testbeam-DESY14 testbeam-SPS12 testbeam-SPS11 testbeam-SPS10 testbeam-SPS09 testbeam-SPS08 LP-TPC
  Belle testbeam at SPS in June 2015, Page 1 of 6  Not logged in ELOG logo
New entries since:Thu Jan 1 01:00:00 1970
Entry  Tue May 12 10:27:39 2015, Benedikt Würkner, SVD3 (H6B), Setup information, , , , , Unknown spider-config.jpg
Information concerning the SVD3 setup during a beam test

In the beam area setup the whole crate and the power supply with the usual spider cable and the two Keithly 2410 high voltage supplies.
Monitoring of the 2410 happens via a NI MAX interface that connects to the GPIB-Ethernet interface and needs to be configured there. The IP and password
Entry  Wed Jun 3 10:48:42 2015, Benedikt Würkner, common, Networking, , , , , Unknown 
WLAN Router:

SSID: Hephy

password: 20supersecret14

DHCP Range: 192.168.0.200 to 239
Entry  Wed Jun 3 17:23:07 2015, Thomas Bergauer, Belle II FADC (H6A), XY stage positions, , , , , Unknown L5_Class_B-.PNG
x-Achse: positiv Richtung Saleve (counting room)

y-Achse: positiv Richtung UNTEN!!
Entry  Thu Jun 4 14:15:50 2015, Hao Yin, Belle II FADC (H6A), FIR, 001, , , , Good 
FIR filer and ADC delay with all sensor and telescope.
telescope n-side switched.
Entry  Thu Jun 4 14:16:20 2015, Hao Yin, Belle II FADC (H6A), Pedestal, 001, 10000, , , Good 
FirRun001, room temp
telescope n-side switched.
Entry  Thu Jun 4 15:12:41 2015, Hao Yin, Belle II FADC (H6A), Hardware, 001, 50000, 1, No, Good 20x
PedestalRun001, FIRRun001, room temp
telescope n-side switched.
In order to correct the position change the
Entry  Thu Jun 4 18:44:50 2015, Hao Yin, Belle II FADC (H6A), Hardware, 002, 50000, 2, No, Good 19x
room temp, FIRRun001, pedestal run 003
Entry  Thu Jun 4 18:45:42 2015, Hao Yin, Belle II FADC (H6A), Pedestal, 003, 10000, , , Good 
firrun003, room temp
 
Entry  Thu Jun 4 18:49:03 2015, Benedikt Würkner, SVD3 (H6B), Setup, , , , , Unknown IMG_20150604_184442.jpgIMG_20150604_184451.jpgIMG_20150604_184516.jpg
 
Entry  Thu Jun 4 22:07:16 2015, Hao Yin, Belle II FADC (H6A), Hardware, 003, 189k, 3, No, Good 21x
CE. pedestal run 003. Fir run 002. Room temp
Entry  Fri Jun 5 08:20:27 2015, Hao Yin, Belle II FADC (H6A), Hardware, 004, 50000, 4, No, Good 16x
room temp, FIRRun002, pedestalrun003, taget FW
Entry  Fri Jun 5 12:02:29 2015, Hao Yin, Belle II FADC (H6A), Sixlet Calibration, 001, , , , Good 
room temp max subevent at 2. with lat = 96
Entry  Fri Jun 5 12:03:34 2015, Hao Yin, Belle II FADC (H6A), Sixlet Calibration, 002, , , , Good 
lat = 97 to a greater range of lat scan
Entry  Fri Jun 5 19:55:00 2015, Hao Yin, Belle II FADC (H6A), Sixlet Calibration, 003, , , , Unknown 
lat = 98

room temp

pedestalrun 003
Entry  Fri Jun 5 19:59:44 2015, Hao Yin, Belle II FADC (H6A), Pedestal, 004, 10000, , , Good 
update pedestal values for room temp sixlet runs.
 
Entry  Fri Jun 5 23:38:51 2015, Hao Yin, Belle II FADC (H6A), Pedestal, 005, 10000, , , Unknown 
Readjust after cooling box.

room temp, firrun002
 
Entry  Fri Jun 5 23:39:49 2015, Hao Yin, Belle II FADC (H6A), Hardware, 005, ~200k, 5, No, Good 21x
FIRRun002, pedestalrun005, room temp
Target BW: beam spot at ~ (0 p, 0 n)
Entry  Sat Jun 6 12:43:55 2015, Hao Yin, Belle II FADC (H6A), Hardware, 006, 50000, 6, No, Good 20x
FIRRun002, room temp, pedestalrun005,
layout: same as HW 005
target: -z, pos 6 (strip: p-0, n-0);
Entry  Sat Jun 6 14:28:28 2015, Hao Yin, Belle II FADC (H6A), Harware, 007, 50000, 7, No, Good 20x
room temp, FIRRun002, PedestalRun005, room temp

target: CE, pos 7 (p-0, n-0)
Entry  Sat Jun 6 16:14:36 2015, Benedikt Würkner, SVD3 (H6B), calibration run and setup information, cal01, , , , Unknown 
Calibration Run with +- 50V Bias with higher compliance since the p-side draws more current than expected (23muA by the MAMBO)

 
ELOG V3.1.5-fc6679b