 Mon May 25 20:27:23 2015, Hao Yin, Belle II, system, Caen PS base line measurements, 
|
Baseline noise measurements wo injection.
measure noise in both HV and LV.
wings of APV25 using cmc with 128 strip are visible wo injection. (folder CAEN_PS, run name Noise_xxx.dat). |
|
Wed May 27 09:30:54 2015, Hao Yin, Belle II, system, CAEN PS Primary side,
|
Measured Primary side of caen wo load (setup attachment 2 and prelimilary res. attachment 1. )
and with load (attachment 3: Load, att. 4 corresponding circuit scheme) |
|
Mon Nov 30 17:13:47 2015, Hao Yin, Belle II, system, PedestalRun,
|
ADC Hot, FIRRun001
room temp pedrun |
|
Mon Nov 30 17:23:51 2015, Hao Yin, Belle II, system, HardwareRun001,
|
ADC Hot, FIRRun001, PedestalRun001
room temp pedrun
target: BW |
|
Mon Nov 30 17:47:54 2015, Hao Yin, Belle II, system, HardwareRun002,
|
ADC Hot, FIRRun001, PedestalRun001
target: -Z
room temp pedrun |
|
Mon Nov 30 18:32:13 2015, Hao Yin, Belle II, system, ADC Delay Scan Cold,
|
| ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns) |
|
Mon Nov 30 18:44:04 2015, Hao Yin, Belle II, system, FIRRun_Cold,
|
ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns)
|
|
Mon Nov 30 18:45:49 2015, Hao Yin, Belle II, system, PedestalRun_Cold,
|
ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns), FIRRun_Cold_001
|
|
Mon Nov 30 18:49:23 2015, Hao Yin, Belle II, system, Hardware_Cold,
|
ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns), FIRRun_Cold_001
target: -Z
|
|
Mon Nov 30 19:01:54 2015, Hao Yin, Belle II, system, Hardware_Cold,
|
ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns), FIRRun_Cold_001
Temp = 0°C
target: CE |
|
Mon Nov 30 19:48:05 2015, Hao Yin, Belle II, system, Hardware_Room_With_Cold_I2C,
|
ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns), FIRRun_Cold_001
with room temp i2c config
Temp = 0°C |
|
Mon Nov 30 20:06:15 2015, Hao Yin, Belle II, system, Hardware_Room_With_Cold_I2C,
|
ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns), FIRRun_Cold_001
with room temp i2c config
Temp = room |
|
Mon Nov 30 20:16:37 2015, Hao Yin, Belle II, system, Hardware_Room_With_Cold_I2C,
|
ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns), FIRRun_Cold_001
ADC delay shifted by 3 (1.5ns) all sensors
with room temp i2c config |
|
Mon Nov 30 20:27:42 2015, Hao Yin, Belle II, system, Hardware_Room_With_Cold_I2C,
|
ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns), FIRRun_Cold_001
ADC shifted by 5 (2.5ns) all sensors
with room temp i2c config |
|
Mon Nov 30 22:35:41 2015, Hao Yin, Belle II, system, Hardware_Room_With_Cold_I2C,
|
ADC Cold diff to hot: 1-3 adc delay config (max 1.5 ns), FIRRun_Cold_001
ADC shifted by 9 (4.5ns) all sensors
with room temp i2c config |
|
Mon Nov 30 15:18:12 2015, Hao Yin, Belle II, module, ADC_DELAY_HOT, ADC delay hot
|
ADC delay scan at room temp and 20 min after APV I2C config.
measured values at display in the FIR_HOT cfg file.
17:06 first run 20 min after i2c config. |
|
Fri May 22 12:01:32 2015, Hao Yin, , , , CMC injection LV 10V
|
Comparison w/o filter (LC) connected to -z_n side.
Mateo has the results. |
|
Tue May 19 13:23:16 2015, Hao Yin, Belle II, system, Calibration, CalibrationRun001
|
PedestalRun001, FIRRun001,
room temperature,
no noise injection |
|
Mon May 25 10:38:03 2015, Hao Yin, Belle II, system, L5 Ladder Emission Test, Emission
|
(TestNr: 16)
base line noise measurement are saved in SYSTEM_CHECK_AFTER_WE.
(noise wings at fw n side decreased !!!) |
|
Tue May 19 10:08:53 2015, Hao Yin, , , , FADC system setup success
|
3 FADC. All Channel/APV25 running (except L3 n first and last -> not connected (bonding))
n-side: all connectors
p-side: 0x01: 1, 2, 4 and 0x02, 1 with L3 p and L4 p (Telescope) |
|