ELOG testbeam-SPS09

APVDAQ standalone 40 MHz hit mode

4 Belle DUTs
HV=80V, 40 MHz, 6 sample, 120 GeV

beam position: p-side: APV2 of Origami, n-side: between APV1 and 2 of Origami (center of sensors)
table position y (height): 94.3

zero supressed w/o bad strip definition of origami module

JP-module is hit at APV3, module seems to be on a higher position than in past beam test (eventuelly flipped)

Fri Aug 21 12:06:06 2009

APVDAQ standalone 40 MHz

4 Belle DUTs
HV=80V, 40 MHz, 6 sample, 120 GeV

beam position: p-side: APV2 of Origami, n-side: between APV1 and 2 of Origami (center of sensors)

JP-module is hit at APV3, module seems to be on a higher position than in past beam test (eventuelly flipped)

zero supressed w bad strip definition of origami module, but reverse readout order of APV 2 and 3 on p-side

103

Tue Aug 25 20:21:31 2009

APVDAQ + telescope 40 MHz transparent mode

Belle DUT, HV=80V, 40 MHz, 120 GeV
6 samples, transparent mode
no cooling
after realignement of modules
new beam spot:

APV #	n-side	p-side
JP	1/2	1/2
Origami	2/3	1/2
Flex	1/2	1/2
Micron	0/1	1/2

Thu Aug 20 12:50:59 2009

bottom right on sensor, point 4

alignment_beam

2 alignement modules

location in beam direction: h04-h03

beam in center of sensor

HV=70V, 40MHz, 6 samples

beam on, 120 GeV

module 1 (h03) is used w inverter off and higher base line

XY coordinates: X:43 y:155 (bottom right on sensor in beam direction)

Fri Aug 21 06:31:29 2009

4 Belle DUTs
HV=80V, 40 MHz, 6 sample, 120 GeV

beam position: p-side: APV2 of Origami, n-side: between APV1 and 2 of Origami (center of sensors)

JP-module is hit at APV3, module seems to be on a higher position than in past beam test (eventuelly flipped)

run interrupted after 80173 --> bad timing, peak was at 4 th or 5 th sample

Sat Aug 22 03:27:13 2009

APVDAQ + telescope 31,8 MHz transparent mode (cooling?)

HV=80V, 31.8 MHz, beam on, 120 GeV

6 samples

chiller set to 13 deg.

f=31.8 MHz

config file: cern09_belle_31.8mhz_multi6.cfg

there was probably no water flow throught the pipe of the origami module during this run --> must be repeated

Sat Aug 22 08:32:02 2009

APVDAQ + telescope 31,8 MHz hit mode (cooling?)

HV=80V, 31.8 MHz, beam on, 120 GeV

6 samples, hit mode, hitcut=4

chiller set to 13 deg.

f=31.8 MHz

config file: cern09_belle_31.8mhz_hit_multi6.cfg

there was probably no water flow throught the pipe of the origami module during this run --> must be repeated

Sat Aug 22 09:44:50 2009

APVDAQ + telescope 31,8 MHz hit mode (cooling?)

HV=80V, 31.8 MHz, beam on, 120 GeV

6 samples, hit mode, hitcut=5

chiller set to 13 deg.

f=31.8 MHz

config file: cern09_belle_31.8mhz_hit_cut5_multi6.cfg

there was probably no water flow throught the pipe of the origami module during this run!

Sat Aug 22 10:28:50 2009

APVDAQ + telescope 40 MHz hit mode (cooling?)

HV=80V, 40 MHz, beam on, 120 GeV

6 samples, hit mode, hitcut=4

chiller set to 13 deg.

f=40 MHz

config file: cern09_belle_hit_multi6.cfg

there was probably no water flow throught the pipe of the origami module during this run!

Sat Aug 22 11:26:00 2009

APVDAQ + telescope 40 MHz hit mode (cooling?)

HV=80V, 40 MHz, beam on, 120 GeV

6 samples, hit mode, hitcut=5

chiller set to 13 deg.

f=40 MHz

config file: cern09_belle_hit_cut5_multi6.cfg

trigger rate about 3500 ev / spill

there was probably no water flow throught the pipe of the origami module during this run!

Sat Aug 22 15:52:33 2009

APVDAQ + telescope 31.8 MHz transparent mode + cooling

Belle DUT, HV=80V, 31.8 MHz, 120 GeV
6 samples, transparent mode
chiller set to 13 deg, 2900 rpm

water flow checked befor start of run

Sat Aug 22 19:19:20 2009

APVDAQ + telescope 40 MHz transparent mode + cooling

Belle DUT, HV=80V, 40 MHz, 120 GeV
6 samples, transparent mode
chiller set to 13 deg, 2900 rpm

water flow checked befor start of run

Fri Aug 21 06:34:39 2009

APVDAQ + telescope 40 MHz

was originally run004, renamed after run was stopped to avoid duplicate names
4 Belle DUTs
HV=80V, 40 MHz, 6 sample, 120 GeV
beam position: p-side: APV2 of Origami, n-side: between APV1 and 2 of Origami (center of sensors)
table position y (height): 94.3

JP-module is hit at APV3, module seems to be on a higher position than in past beam test (eventuelly flipped)

same as run6873, but w improved timing --> peak is now at sample 2 or 3

since eudetmac was not reachable by VNC, the telescope has not been restarted !

Fri Aug 21 12:06:29 2009

APVDAQ standalone hit mode 40 MHz

4 Belle DUTs
HV=80V, 40 MHz, 6 sample, 120 GeV

beam position: p-side: APV2 of Origami, n-side: between APV1 and 2 of Origami (center of sensors)

JP-module is hit at APV3, module seems to be on a higher position than in past beam test (eventuelly flipped)

same as run6873, but w improved timing --> peak is now at sample 2 or 3

since eudetmac was not reachable by VNC, the telescope has not been restarted !

zero supressed w bad strip definition of origami module, but natural readout order of APV 2 and 3 on p-side

hit cut = 4

Fri Aug 21 12:06:39 2009

APVDAQ standalone hit mode 40 MHz

4 Belle DUTs
HV=80V, 40 MHz, 6 sample, 120 GeV

beam position: p-side: APV2 of Origami, n-side: between APV1 and 2 of Origami (center of sensors)

JP-module is hit at APV3, module seems to be on a higher position than in past beam test (eventuelly flipped)

same as run6873, but w improved timing --> peak is now at sample 2 or 3

since eudetmac was not reachable by VNC, the telescope has not been restarted !

zero supressed w bad strip definition of origami module, but natural readout order of APV 2 and 3 on p-side

hit cut = 5

Fri Aug 21 12:22:43 2009

APVDAQ standalone 31.8 MHz hit mode

4 Belle DUTs
HV=80V, 31.8 MHz, 6 sample, 120 GeV
switched to external clock source
processed mode, hit cut = 4
beam position: p-side: APV2 of Origami, n-side: between APV1 and 2 of Origami (center of sensors)

JP-module is hit at APV3, module seems to be on a higher position than in past beam test (eventuelly flipped)

Fri Aug 21 13:38:20 2009

APVDAQ standalone 31.8 MHz hit mode

run011

75000

21.08.2009 13:35:25

4 Belle DUTs
HV=80V, 31.8 MHz, 6 sample, 120 GeV
external clock source
processed mode, hit cut = 5
beam position: p-side: APV2 of Origami, n-side: between APV1 and 2 of Origami (center of sensors)

JP-module is hit at APV3, module seems to be on a higher position than in past beam test (eventuelly flipped)

Sat Aug 22 01:06:34 2009

APVDAQ + telescope 40 MHz transparent mode (cooling?)

Belle DUT, tranparent mode
HV=80V, 40 MHz, beam on, 120 GeV
6 samples
chiller set to 13 deg.

beam position: p-side: APV2 of Origami, n-side: between APV1 and 2 of Origami (center of sensors), beam spot: 9x9 mm
JP-module is hit at APV3, module seems to be on a higher position than in past beam test (eventuelly flipped)

APVDAQ and telescope runs are not synchronized

trigger rate: about 300 - 500 ev / spill

there was probably no water flow throught the pipe of the origami module during this run --> must be repeated

Thu Aug 20 15:15:33 2009

bottom center on sensor, point 6

alignment_beam

run6869

615 (beam manipulation by students)

20.08.2009 14:56:16

20.08.2009 15:14:11

2 alignment modules

location in beam direction: h04-h03

beam in center of sensor

HV=70V, 40MHz, 6 samples

beam on, 120 GeV

module 1 (h03) is used w inverter off and higher base line

XY coordinates: X:50 y:155 (bottom center on sensor in beam direction)

Fri Aug 21 18:35:13 2009